B.E.G. LUXOMAT PD5-M-1C-Clip Installation And Operating Instruction

LUXOMAT
Installation and Operating Instruction
1. Mounting preparations
Work on the 230 V mains supply
may only be carried out by qualified
professionals or by instructed persons
under the direction and supervision of
qualified skilled electrical personnel
in accordance with electrotechnical
regulations.
Disconnect supply before installing!
When in Master/Slave mode of
operation, the Master-appliance must
always be installed at the location
where there is least daylight.
4. Self test cycle
2000
1200
600
200
40
The product enters an initial 60-second
self-test cycle, when the supply is first
connected. The occupancy detector is
ready for operation.
Option:
IR-PD
Wall bracket for remote
control IR-PD
IR-PD-Mini
®
2. Installation
The LUXOMAT PD5-M-1C-Clip is supplied
®
with a 90 cm long, 5 x 0.75, colour-coded
cable and is pre-wired.
120 60 50
A
40
30
5. Putting into operation / Settings 15
5
10
120 60 50
A
40
Follow-up time for light control
30
16 10
15
5 The time can be set infinitely variably at between
5 10
2
15 sec. and 16 min.
1
TEST
30
15
Symbol TEST: test mode (every movement switches on
16 10
5
the light for a period of 1 second, switching it off for a
2
period of 2 seconds after that regardless of the level of
2000 1
TEST
30
15
1200
brightness)
600
200
40
Twilight-switch for light control (relay 1)
2000
1200
The switch-on value for the light can be set at between 10
600
and 2000 Lux. Using the rotary control, the luminance set
200
40
points can be set as desired.
Symbol : Night-time operation
Symbol : Daytime /Night-time operation
Settings for master with remote control
Settings for relay
Channel 1:
Reset when open:
Deletes all values
��
set with the or
��� ����
���
50
1500
remote control;
Lux Lux
the settings on
the potentiometer
max
apply
or
ON
OFF
t < 5 s
50
Note: The buttons for channel 2 (R2) have
Lux
no function for the PD5-M-1C-Clip.
max
ON
OFF
PD5-M-1C-Clip
The detector has been specially developed
for clipping onto fluorescent lamps of size
T5+T8.
It is particularly suitable for use with
suspended light-strips or for ceiling appli-
cations where holes caused by installation
are to be avoided. Two clip sizes of the
type required are enclosed. Carry out the
clipping-on procedure as follows:
The height-adjustable clip can be inserted
in the housing easily as long as the mark-
ings on the clip-shaft and the housing are
in line with each other. Once the correct
distance to the light has been established,
lock the shaft by rotating through 90° in
an anti-clockwise direction.
Unlocking device
��
��� ��
���
Fully automatic/semi automatic
mode (see page 2, point 5)
Lock device
Permanent tamper protection
max
ON
1500
Lux
OFF
3. Detection area
Mounting Range (circular detection) T=18°C
height
seated
2.00 m r = 2.00 m
2.50 m r = 2.50 m
3.00 m r = 3.00 m
3.50 m –
4.00 m –
4.50 m –
5.00 m –
6. Settings carried out using remote control (optional)
Remote control LUXOMAT IR-PD
®
120 60 50
A
40
1. Check Battery:
30
15
5 10
open battery compartment by pressing the
plastic springs together and removing the
16 10
5
battery-holder.
2
1
TEST 30
15
1 2
2. IMPORTANT
25 22
30 2000
18
1200 Please pay attention, that the setting is Potentio-
R1 16
600
10 meter 1 at "TEST" and Potentiometer 2 not at
200
6 40
TEST
3
1
"SUN". All values which have been program-
med using the remote control will be deleted in
the event of power failure in the position "TEST /
1 2
SUN". Please switch Potentiometer 2 over to
25 22
2000 "MOON" or any other value.
30
18
1200
R1 16
600
10
6 200
TEST 3
1 40
Caution:
Settings with remote control supersede the
settings by courtesy of potentiometers.
Explanation of button functions
�� ����
Target value for brightness
��� ���
Automatic reading in of the current light value
as a new target light value
�� ��
Lag times for channel 1
��� ���
Pulse function for channel 1, 1s every 9 s on motion detection
The pulse function can only be selected in fully automatic mode.
Activate test mode when closed
To deactivate: press reset
Resetting when closed
The lighting relay is switched off, i.e.
opened and the follow-up times reset.
Permanent protection against sabotage
This function blocks the unit permanently (green LED is
illuminated). This operating mode can only be activated
t < 5 s during the period of 5 seconds after pressing the "lock"
button. This status will only permit actuating the function
"Light on/Light off". The procedure for leaving this mode is as
follows:
1. Switch off the current
2. Apply current for 31 - 59 seconds (green LED flashes)
3. Switch of the current again
4. Apply current, wait for selftest cycle
50
1500
Lux
Lux
5. Open detector
Light on/off when closed
The light will remain switched on/ off for as long as move-
ments are detected in the areas of coverage. Once the last
movement has been detected, the light will remain on for the
duration of the follow-up time as per setting.
The appliance will then return independently to the mode
selected (Fully or Semi-automatic).
GB
walking walking
across towards
r = 4.00 m r = 2.00 m
r = 5.00 m r = 3.00m
r = 6.00 m r = 3.70 m
r = 7.00 m r = 4.30 m
r = 8.00 m r = 4.80 m
r = 9.00 m r = 4.50 m
r = 10.00 m r = 6.00 m