Kaiterra Sensedge Mini Installation Manual
Electrical box mount
Hide thumbs
Also See for Sensedge Mini:
- Installation manual (26 pages) ,
- User manual (13 pages) ,
- Manual (13 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for Kaiterra Sensedge Mini
Summary of Contents for Kaiterra Sensedge Mini
- Page 1 Sensedge Mini Installation Guide Electrical Box Mount (EU)
-
Page 2: What You Will Need
What you will need Pa ts Sensedge Mini Sensedge Mini Electrical box Electrical box Fastening USB cable & Charger sensor modules x 2 mount screws (EU) x 2 screws x 2 (Power via USB-C only) Tools Cross screwdriver... - Page 3 Where to place your Sensedge Mini 1.7m Install your device in occupied space at 1.1-1.7m (3.6-5.6 ft) 5.6ft above the floor (away from doors, windows, air supply and zones where occupants may exhale directly into the sensor). Please make sure that your desired mounting location is close to a power source.
-
Page 4: Know Your Device
Air intake On/Off switch Air is drawn into the Sensedge Mini from the lower side, as well as the air intake on the upper side.It is vital that neither side of the device is covered. Any changes in airflow may affect the readings and accuracy. - Page 5 Install the Electrical Box Mount Find the Electrical Box Mount (rectangular shaped) included in the packaging. Line up the plate with your in-wall electrical box and mount it in place using provided Electrical Box Screws and the two screw holes indicated below. Electrical box screws (EU) x 2...
- Page 6 Choose your power option The Sensedge Mini supports both USB-C and direct wiring power options. Choose the power option best suited for your project and follow the instructions accordingly. A. Power the device with USB-C cable and adapter Power the Sensedge Mini by connecting the device to a charging port using the USB-C cable and adapter.
- Page 7 B. Power the device via direct wiring IMPORTANT SAFEGUARDS · Please use a power source within the range in the product specification. Please contact the facility manager or other responsible personnel if the power source specification is not clear. · The device must be installed by certified electricians or other authorized personnel ONLY.
- Page 8 Turn on the device and check for power connection Move the ON/OFF switch to turn on the device. The STATUS light will go on briefly to indicate the device has been powered on.
- Page 9 Choose your connectivity option The Sensedge Mini supports Wi-Fi, ethernet, and Modbus via RS-485 for connectivity. Choose the connectivity option best suited for your project and follow the instructions accordingly. A. Set up Wi-Fi Prepare for Configuration Download the Kaiterra Configuration Tool and install it on your computer.
- Page 10 Connect to Wi-Fi Open network settings on your computer and look for the Wi-Fi network that starts with “Kaiterra”. Connect your computer to that network. On the Configuration Tool, you can enter a name for the device (e.g. the location of the device or the serial number) and a project tag.
- Page 11 Check for Connectivity The STATUS light will flash in green during the pairing process, and eventually go off when the connection is successfully completed.
- Page 12 B. Set up ethernet Run your Ethernet cable through the opening on the plate, and into the Ethernet port on the back side of the device. You should hear a click sound and see a green light on the cable port. If DHCP mode is used, your connection should be completed.
- Page 13 Manual Mode - Prepare for Configuration If you choose to set up manual mode, please download the Kaiterra Configuration Tool and install it on your computer. After the device has been turned on, it will automatically enter the configuration mode for 15 minutes. The STATUS light will flash in yellow.
- Page 14 · · Subnet mask · Gateway Click save and disconnect your computer from the “Kaiterra” network. Check for Connectivity The STATUS light will flash in green during the pairing process, and eventually go off when the connection is successfully completed.
- Page 15 Run the cables through the opening on the plate, and plug the 4-pin Phoenix pin plug into the corresponding terminals on the back of the device. The default Modbus address is set as 1, and can be changed later via the Kaiterra Configuration Tool.
- Page 16 Configure Modbus Settings - Connect to network Open network settings on your computer and look for the Wi-Fi network that starts with “Kaiterra”. Connect your computer to that network. On the Configuration Tool, you can enter a name for the device (e.g. the location of the device or the serial number) and a project tag.
- Page 17 Secure the device in place You will find three slots on the plate and three corresponding protrusions on the back of the device. Line the device up with the plate such that the protrusions are inside the corresponding slots. Rotate gently to secure the device and lock it in place, and use the two fastening screws to fasten the device to the plate.
-
Page 18: Install The Modules
Install the modules To install the sensor module, simply align it with the bay and press it in, ensuring the Kaiterra logo on the plastic tab is facing outwards. When inserted correctly, the module will click into place, and an LED light above the bay will briefly flash red if the device is powered on. - Page 19 Complete Electrical Box Mount Installation! You have completed the installation process. Now follow our to set up your Kaiterra dashboard account and connect your device to the dashboard.
- Page 20 For additional support, please contact your sales representative or contact us at the following email address: support@kaiterra.com...