Farm King 1342 Operator And Parts Manual
Farm King 1342 Operator And Parts Manual

Farm King 1342 Operator And Parts Manual

13” conventional auger mover
Hide thumbs Also See for 1342:

Advertisement

Quick Links

OPERATOR AND PARTS MANUAL
13" CONVENTIONAL AUGER MOVER
Models 1342, 1352, 1362
072020
FK432

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1342 and is the answer not in the manual?

Questions and answers

Summary of Contents for Farm King 1342

  • Page 1 OPERATOR AND PARTS MANUAL 13” CONVENTIONAL AUGER MOVER Models 1342, 1352, 1362 072020 FK432...
  • Page 3 C13 Conventional Auger Mover ECO CHANGE LOG DATE MANUAL MANUAL PRODUCT DESCRIPTION ISSUED AFFECTED UPDATED PRODUCT RELEASE...
  • Page 4 C13 Conventional Auger Mover...
  • Page 5: Table Of Contents

    C13 Conventional Auger Mover TABLE OF CONTENTS Manufacturer’s Statement: For technical reasons, Farm King reserves the right to modify machinery design and specifications provided herein without any preliminary notice. Information provided herein is of descriptive nature. Performance quality may depend on soil fertility, applied agricultural techniques, weather conditions, and other factors.
  • Page 6 C13 Conventional Auger Mover...
  • Page 7 Customer / Owner Signature: Remove this Warranty Registration Form from the Operator And Parts Manual. Make two copies of the form. Send original Warranty Registration Form to Farm King. Give one copy to the customer and the dealer will keep one copy.
  • Page 8 C13 Conventional Auger Mover...
  • Page 9: Introduction

    Farm King equipment. READ AND UNDERSTAND THIS OPERATOR AND PARTS MANUAL BEFORE OPERATING YOUR FARM KING EQUIPMENT. If you have any questions, see your Farm King dealer. This manual may illustrate options and accessories not installed on your Farm King equipment.
  • Page 10 Introduction - C13 Conventional Auger Mover...
  • Page 11 Serial Number: Farm King is continually working to improve its products. Farm King reserves the right to The serial number plate (Item 1) is located on the make any improvements or changes as deemed lift frame [Figure 1].
  • Page 12 Introduction - C13 Conventional Auger Mover EQUIPMENT IDENTIFICATION CONTROL CONSOLE HYDRAULIC CYLINDER HYDRAULIC OIL TANK STEERING LIFT ARMS WHEEL HYDRAULIC PUMP RELIEF VALVE GEARED HUB...
  • Page 13: Safety

    Safety - C13 Conventional Auger Mover SAFETY SAFETY INSTRUCTIONS Safe Operation is The Operator’s Responsibility Safe Operation Needs A Qualified Operator Use Safety Rules Safety Rules For Power Take-Off (PTO) Driven Equipment Machine Requirements And Capabilities Transport Safety FIRE PREVENTION Maintenance Operation Fire Extinguishers...
  • Page 14 Safety - C13 Conventional Auger Mover...
  • Page 15: Safety Instructions

    • The written instructions from Farm King include the result in minor or moderate injury. It may also Warranty Registration, Dealer Inspection Report, be used to alert against unsafe practices.
  • Page 16: Use Safety Rules

    Safety - C13 Conventional Auger Mover Use Safety Rules Safety Rules For Power Take-Off (PTO) Driven Equipment • Read and follow instructions in this manual and the tractor’s Operators Manual before operating. • Keep PTO shields and all guards in place. Replace damaged or missing shields and guards before •...
  • Page 17: Machine Requirements And Capabilities

    Safety - C13 Conventional Auger Mover Machine Requirements And Capabilities Transport Safety • Stop the machine and engage the parking brake. • Do not exceed 20 mph (32 kph). Reduce speed on Install blocks in front of and behind the rear tires of rough roads and surfaces.
  • Page 18: Fire Prevention

    Fueling Operation • The Farm King machine must be in good operating condition before use. • Check all of the items listed on the service schedule under the 8 hour column before operation. (See Maintenance section) •...
  • Page 19: Gas Engine Safety

    Safety - C13 Conventional Auger Mover GAS ENGINE SAFETY periodically and replace, if necessary. If engine is equipped with a muffler deflector, inspect periodically • Before starting engine, read and understand the and replace, if necessary with correct deflector. operating and maintenance instructions that came •...
  • Page 20: Operating Safety Zone

    Safety - C13 Conventional Auger Mover OPERATING SAFETY ZONE WARNING AVOID INJURY OR DEATH • Do not allow small children, bystanders or unauthorized persons in the work area during operation. • Never stand or work under the auger and undercarriage when in the raised position or during operation.
  • Page 21: Assembly

    Assembly - C13 Conventional Auger Mover ASSEMBLY GENERAL ASSEMBLY INFORMATION BASE FRAME LIFT ARMS HYDRAULIC PUMP OIL TANK CONSOLE HOSES Identification Routing ELECTRICAL...
  • Page 22 Assembly - C13 Conventional Auger Mover...
  • Page 23: General Assembly Information

    • Keep away from power lines when unloading replacement parts are required, contact your and assembling the auger. Farm King Dealer. • Electrocution can occur without direct contact. Assemble the auger mover in the following order: Undercarriage / lift arms WARNING 2.
  • Page 24: Base Frame

    Assembly - C13 Conventional Auger Mover BASE FRAME Figure 5 Figure 4 Position the LH and RH geared hub assemblies (Item 1) to the axle. The locking pin (Item 2) must be positioned facing upwards [Figure 5]. Attach the each geared hub assembly to the axle using eight 1/2”...
  • Page 25 Assembly - C13 Conventional Auger Mover Figure 7 Figure 8 Install the LH (Item 1) and RH (Item 2) hubs into the mover axle (Item 3). The RH hub is installed to the same side as the console mount (Item 4) [Figure 8].
  • Page 26 Assembly - C13 Conventional Auger Mover Figure 10 Figure 12 Position the LH and RH mover arms (Item 1) with Install one adjustable rod (Item 1) between the LH the brackets on the axle. Attach each arm using and RH hub brackets [Figure 12]. four 1/2”...
  • Page 27 Assembly - C13 Conventional Auger Mover Figure 14 Figure 15 Position the steering hydraulic cylinder (Item 1) Install the relief valve to the mount on the RH within the axle mounts [Figure 14]. side of the axle using two 5/16” x 2-1/2” hex bolts (Item 1) and two 5/16”...
  • Page 28: Lift Arms

    Assembly - C13 Conventional Auger Mover LIFT ARMS Figure 18 Figure 16 Position the upper lift arm (Item 1) on top of the lower lift arm. Align the holes and install one 1” x 8.82” pin (Item 2), two 1” flat washers (both Move the lower lift arm (Item 1) into position sides), and two cotter pins [Figure 18].
  • Page 29 Assembly - C13 Conventional Auger Mover Figure 20 WARNING AVOID INJURY OR DEATH Keep fingers and hands out of pinch points when assembling the equipment. Place the mover hydraulic cylinder (Item 1) between the upper and lower lift arms [Figure 20]. Attach the rod end to upper lift arm using one 5/8”...
  • Page 30: Hydraulic Pump

    Assembly - C13 Conventional Auger Mover HYDRAULIC PUMP Figure 22 Figure 21 Attach the handle (Item 1) to the pump mount plate (Item 2) using: • One 1/2” X 1-1/2” hex bolt and one 1/2” flat washer (before the handle) (Item 3) •...
  • Page 31 Assembly - C13 Conventional Auger Mover Figure 23 Figure 24 Position the pump arm (Item 1) on the inside of the mount plate. Attach the top hole of the pump arm to the mount plate using one 1/2” X 1-1/2” hex bolt (Item 2), Attach one belt guide (Item 1) to the inside of the two 1/2”...
  • Page 32 Assembly - C13 Conventional Auger Mover Figure 25 Figure 26 Install one -10 MORB x -8 MJIC elbow fitting (Item 1) to the pump port on same side as the belt guide (Item 2) [Figure 26]. Install one -16MORB x -12FORB adapter fitting (Item 3) to the remaining pump port [Figure 26].
  • Page 33 Assembly - C13 Conventional Auger Mover Figure 28 IMPORTANT Portions of the auger engine may be need to be disassembled in order to access the engine drive shaft. There are specific pump drive components that must be installed to engine shaft. Figure 27 Install one single sheave 4-1/2”OD pulley (Item 1) to the engine shaft [Figure 28].
  • Page 34 Assembly - C13 Conventional Auger Mover Figure 29 IMPORTANT Continue assembling the standard auger components once the pump drive, spacers, and pulley are installed. Position the pump motor assembly to the auger belt cover. Attach using four 3/8” x 1” hex bolts to the holes at the edge of the cover (Item 1) [Figure 29].
  • Page 35: Oil Tank

    Assembly - C13 Conventional Auger Mover OIL TANK Figure 31 Figure 30 Install one fill cap (Item 1) [Figure 31] to the tank. Install one -4 MPT plug (Item 2) [Figure 31] to the front port. Apply Teflon tape to threads. Figure 32 Bring the oil tank (Item 1) [Figure 30] to the assembly area.
  • Page 36: Console

    Assembly - C13 Conventional Auger Mover CONSOLE Figure 33 CONSOLE BOTTOM VIEW Install fittings and hoses to the valve block, ball valve, and bypass valve [Figure 33], see chart: ITEM PART NUMBER DESCRIPTION QTY. 937638 PLUG-8MORB 811414 ELBOW 90 3/4 MORB X 3/4 MJIC 811918 ELBOW 90 9/16SWMORB x 9/16MJIC 812080...
  • Page 37 Assembly - C13 Conventional Auger Mover Figure 34 Console top view [Figure 34]. Attach the ball valve and bypass valve using 5/16” x 1” carriage bolts (Item 1) and 5/16” lock nuts [Figure 34]. Attach the valve block using 5/16” x 2-1/2” hex bolts (Item 2) and 5/16”...
  • Page 38: Hoses

    Assembly - C13 Conventional Auger Mover HOSES Identification Figure 35 OIL TANK LH WHEEL MOTOR MOVER PUMP AUGER LIFT CYLINDER RELIEF VALVE RH WHEEL MOTOR...
  • Page 39 Assembly - C13 Conventional Auger Mover Figure 36 MOVER LIFT CYLINDER STEERING CYLINDER BALL VALVE CONSOLE VALVE BLOCK...
  • Page 40 Assembly - C13 Conventional Auger Mover Install hoses, depending on model [Figure 35], [Figure 36]. See chart: HOSES - C1342 ITEM DESCRIPTION LENGTH 936002 HOSE-6 X -6JIC X -6JIC 64” 936002 HOSE-6 X -6JIC X -6JIC 64” 913756 HOSE-8 X -8JIC X -8JIC 200”...
  • Page 41 Assembly - C13 Conventional Auger Mover Figure 37 LH WHEEL MOTOR RELIEF VALVE RH WHEEL MOTOR Install relief valve hoses (all models) [Figure 37]. See chart: ITEM DESCRIPTION LENGTH 913967 HOSE-6 X -6JIC X -6JIC 90 ELBOW 12” 913967 HOSE-6 X -6JIC X -6JIC 90 ELBOW 12”...
  • Page 42: Routing

    Assembly - C13 Conventional Auger Mover Routing Figure 38 THROUGH LH MOVER ARM TO PUMP OP HOSE ON AXLE ALONG AXLE, THROUGH GROMMETS OF DIESEL ENGINE MOUNT P-CLIPPED TO UPPER SCISSOR LIFT ARM RUN UNDERNEATH AXLE THROUGH RH LOWER SCISSOR LIFT ARM RUN OVER AXLE THROUGH RH MOVER ARM...
  • Page 43 Assembly - C13 Conventional Auger Mover Figure 39 UGH LH R ARM THROUGH LH MOVER ARM TIE WRAPPED TO LOWER MOVER SCISSOR LIFT ARM SADDLE CLAMPED ONTO MOVER AXLE SADDLE CLAMPED ONTO VERTICAL PORTION OF CONTROL CONSOLE, 2 PLCS THROUGH RH MOVER ARM CONNECT TO BALL VALVE...
  • Page 44 Assembly - C13 Conventional Auger Mover See hose routing [Figure 38], [Figure 39]. Figure 42 IMPORTANT HOSE ROUTING Hoses and wire harnesses are routed together through the mover arms and must be pulled LEAVE SLACK through at the SAME TIME. Cannot be done IN HOSE after or before.
  • Page 45: Electrical

    Assembly - C13 Conventional Auger Mover ELECTRICAL Figure 45 For mover models, route the electrical harness to the console instead of the intake of the auger. Route the electrical harness up inside the console. Install the E-stop (Item 1) and electric clutch (Item 2) connections [Figure 45].
  • Page 46 Assembly - C13 Conventional Auger Mover...
  • Page 47: Operation

    Operation - C13 Conventional Auger Mover OPERATION GENERAL INFORMATION Pre - Operation Checklist Break - In Checklist Engine Requirements ENTERING & LEAVING THE OPERATOR’S POSITION Entering The Operator’s Position Leaving The Operator’s Position ENGINE BELT DRIVE MOVING AUGER RAISING / LOWERING AUGER TRANSPORTING...
  • Page 48 Operation - C13 Conventional Auger Mover...
  • Page 49: General Information

    Operation - C13 Conventional Auger Mover GENERAL INFORMATION Note: Do not operate with hydraulic leaks. Pre - Operation Checklist 5. Check and tighten all wheel bolts to proper torque. Before operating the auger for the first time and 6. Check tire pressure. Inflate per manufacturer’s each time thereafter, check the following items: specification.
  • Page 50: Break - In Checklist

    Operation - C13 Conventional Auger Mover Break - In Checklist Engine Requirements There are no operational restrictions on the auger The C13 Conventional Auger Mover is designed to or auger mover when used for the first time. It be used with an engine of appropriate power. The is recommended that the following mechanical following engines are recommended.
  • Page 51: Entering & Leaving The Operator's Position

    Operation - C13 Conventional Auger Mover ENTERING & LEAVING THE ENGINE BELT DRIVE OPERATOR’S POSITION Engine model operation: Entering The Operator’s Position Disengage auger drive. Enter the operator’s position, start the engine, and 2. Move the throttle to its mid-range position. release the parking brake.
  • Page 52: Moving Auger

    Operation - C13 Conventional Auger Mover MOVING AUGER IMPORTANT Clear the area of bystanders, especially small children, before starting. Be sure there is enough clearance from overhead The locking pin (Item 2) must always be in obstructions and power lines or other equipment. place, whether wheel motors are engaged or disengaged [Figure 48].
  • Page 53 Operation - C13 Conventional Auger Mover WARNING Keep wheels of undercarriage level and on firm ground while moving the auger. Be aware of any obstructions in the line of travel of the auger. Adjust the bypass valve (Item 5) to change hydraulic flow to each drive motor [Figure 49].
  • Page 54: Raising / Lowering Auger

    Operation - C13 Conventional Auger Mover RAISING / LOWERING AUGER WARNING Clear the area of bystanders, especially small children, before starting. Be sure there is enough clearance from overhead Never attempt to raise or lower the auger obstructions and power lines or other equipment. during operation.
  • Page 55: Transporting

    Operation - C13 Conventional Auger Mover TRANSPORTING IMPORTANT Always comply with federal, state, local and provincial laws regarding the transport of farm equipment on pubic roadways. TRANSPORT STRAP Install the strap around the main tube and IMPORTANT to the mounts (Item 3) [Figure 52] during transport.
  • Page 56 Operation - C13 Conventional Auger Mover WARNING AVOID SERIOUS INJURY OR DEATH DO NOT transport loaded equipment on public roadways. Excess weight will greatly increase tractor stopping distance and may cause the operator to lose control of the tractor or tow vehicle.
  • Page 57: Maintenance

    Maintenance - C13 Conventional Auger Mover MAINTENANCE TROUBLESHOOTING SERVICE SCHEDULE LUBRICATION Recommendations PUMP BELT TENSION HYDRAULIC OIL FILTER WHEELS Torque Wheel Replacement Tire Pressure SAFETY SIGN (DECAL) INSTALLATION STORAGE AND RETURN TO SERVICE Storage Return To Service...
  • Page 58 Maintenance - C13 Conventional Auger Mover...
  • Page 59: Troubleshooting

    NOTE: If a problem is encountered that is difficult to solve, even after having read through this troubleshooting section, please call your local Farm King dealer. Before you call, please have this Operator And Parts Manual and the serial number of your machine at hand.
  • Page 60: Service Schedule

    Maintenance - C13 Conventional Auger Mover SERVICE SCHEDULE Maintenance work must be done at regular intervals. Failure to do so will result in excessive wear and early failures. The service schedule is a guide for correct maintenance of the equipment. WARNING Instructions are necessary before operating or servicing equipment.
  • Page 61: Lubrication

    Maintenance - C13 Conventional Auger Mover LUBRICATION PUMP BELT TENSION Recommendations Figure 55 Always use a good quality multi-purpose / lithium base grease when lubricating the equipment. • Always use a hand-held grease gun. • Clean fitting before greasing, to avoid injecting dirt and grit.
  • Page 62: Hydraulic Oil Filter

    Maintenance - C13 Conventional Auger Mover HYDRAULIC OIL FILTER WHEELS Figure 56 Torque IMPORTANT Check Wheel Nuts After: First 3 (three) hours of field operation. 2. First 10 (ten) hours of field operation. 3. First 50 (fifty) hours of field operation. REPEAT PROCEDURE IF A WHEEL IS REMOVED OR REINSTALLED Torque wheel bolts to proper torque.
  • Page 63: Tire Pressure

    Maintenance - C13 Conventional Auger Mover Tire Pressure WARNING CAUTION AVOID INJURY OR DEATH Always chock tires before performing any maintenance or service. Place chock blocks behind and in front of the opposite tire to be removed. Raise axle frame with jack until the tire / wheel is slightly off the ground.
  • Page 64: Safety Sign (Decal) Installation

    Maintenance - C13 Conventional Auger Mover SAFETY SIGN (DECAL) INSTALLATION • Lubricate all bushings to remove any water residue from washing. • Remove any material that has become entangled IMPORTANT around any moving part. • Inspect the hitch and all welds on the equipment for wear and damage.
  • Page 65: Parts Identification

    Parts Identification - C13 Conventional Auger Mover PARTS IDENTIFICATION GENERAL PARTS INFORMATION MAIN ASSEMBLY GEARED HUB OIL TANK LOWER LIFT ARM UPPER LIFT ARM MOVER BASE - C1342 MOVER BASE - C1352, C1362 STEERING CONSOLE PUMP - C1342 PUMP - C1352, C1362 HYDRAULIC CYLINDER - MOVER LIFT - C1342 HYDRAULIC CYLINDER - MOVER LIFT - C1352, C1362 RELIEF VALVE...
  • Page 66: General Parts Information

    Parts Identification - C13 Conventional Auger Mover GENERAL PARTS INFORMATION The parts identification section list descriptions, part numbers and quantities for all North America Base Model C13 series augers. Contact your Farm King dealer for additional parts information. MAIN ASSEMBLY TO SECURE HOSE...
  • Page 67 Parts Identification - C13 Conventional Auger Mover ITEM PART NUMBER DESCRIPTION QTY. 81546 5/16" FLAT WASHER (PL) 811791 1/2" X 2" HEX BOLT (PL) 812026 5/16" X 1" HEX BOLT (PL) 812362 5/16" LOCK NUT (PL) 812364 1/2" LOCK NUT (PL) 912832 7/16"...
  • Page 68: Geared Hub

    Parts Identification - C13 Conventional Auger Mover GEARED HUB SECTION A-A 17 24 25 11 12 LH HUB RH HUB 938325 938314 938325, 938314...
  • Page 69 Parts Identification - C13 Conventional Auger Mover ITEM PART NUMBER DESCRIPTION QTY. 81531 BOLT HEX 0.25NC X 2.00 GR5 PL 84039 WASHER - 3/8" SAE FLAT (PL) 84050 3/4" S.A.E. FLAT WASHER (PL) 86170 3/8" X 1" HEX BOLT GR.5 (PL) 810149 3/4"...
  • Page 70: Oil Tank

    Parts Identification - C13 Conventional Auger Mover OIL TANK 924094...
  • Page 71 Parts Identification - C13 Conventional Auger Mover ITEM PART NUMBER DESCRIPTION QTY. 811422 ADAPTER - 1/2 MNPT X 3/4 MJIC 812363 3/8" LOCK NUT (PL) 81587 3/8" X 4" HEX BOLT (PL) 910202 10 MICRON OIL FILTER 910212 FILTER HEAD 910442 REDUCER, 3/4"MNPT X 1/2"FNPT 913565...
  • Page 72: Lower Lift Arm

    Parts Identification - C13 Conventional Auger Mover LOWER LIFT ARM 935607 ITEM PART NUMBER DESCRIPTION QTY. 913312 PIN-1.00X8.82 935609 WELDT-LIFTING ARM MOVER 9812433 3/16" X 1 1/2" COTTER PIN 84522 1" ID SAE FLAT WASHER (PL)
  • Page 73: Upper Lift Arm

    Parts Identification - C13 Conventional Auger Mover UPPER LIFT ARM 935608 ITEM PART NUMBER DESCRIPTION QTY. 812639 WASHER 0.625 SAE FLAT BS PL 913300 PIN-0.625X5.51 913312 PIN-1.00X8.82 937534 WELDT-LIFTING ARM MOVER 9812433 3/16" X 1 1/2" COTTER PIN 84522 1" ID SAE FLAT WASHER (PL)
  • Page 74: Mover Base - C1342

    Parts Identification - C13 Conventional Auger Mover MOVER BASE - C1342 935938...
  • Page 75 Parts Identification - C13 Conventional Auger Mover ITEM PART NUMBER DESCRIPTION QTY. 81525 1/4" X 3/4" HEX BOLT (PL) 84048 1/2" SAE FLAT WASHER (PL) 84277 1/2" X 1 1/2" HEX BOLT (PL) 84467 3/4" X 2" HEX BOLT (PL) 84498 1/4"...
  • Page 76: Mover Base - C1352, C1362

    Parts Identification - C13 Conventional Auger Mover MOVER BASE - C1352, C1362 DETAIL B DETAIL A 935701, 933962...
  • Page 77 Parts Identification - C13 Conventional Auger Mover ITEM PART NUMBER DESCRIPTION QTY. 81525 1/4" X 3/4" HEX BOLT (PL) 84048 1/2" SAE FLAT WASHER (PL) 84277 1/2" X 1 1/2" HEX BOLT (PL) 84467 3/4" X 2" HEX BOLT (PL) 84498 1/4"...
  • Page 78: Steering

    Parts Identification - C13 Conventional Auger Mover STEERING USED DURING AUGER TRANSPORTATION 25 11 935937...
  • Page 79 Parts Identification - C13 Conventional Auger Mover ITEM PART NUMBER DESCRIPTION QTY. 81546 5/16" FLAT WASHER (PL) 81564 5/16" X 4.5" HEX BOLT (PL) 84039 WASHER - 3/8" SAE FLAT (PL) 84048 1/2" SAE FLAT WASHER (PL) 87553 1/2" X 1.75" HEX BOLT UNC GR5 (PL) 811795 3/8"...
  • Page 80: Console

    Parts Identification - C13 Conventional Auger Mover CONSOLE 937635...
  • Page 81 Parts Identification - C13 Conventional Auger Mover ITEM PART NUMBER DESCRIPTION QTY. 810761 5/16" X 2 1/2" HEX BOLT (PL) 811414 ELBOW 90 3/4 MORB X 3/4 MJIC 811918 ELBOW 90 9/16SWMORB x 9/16MJIC 812080 ADAPTOR STR 3/4MORB X 3/4MJIC 812107 ADAPTOR STR 3/4MORB X 9/16MJI 812320...
  • Page 82: Pump - C1342

    Parts Identification - C13 Conventional Auger Mover PUMP - C1342 11 10 23 20 19 DETAIL A 935011...
  • Page 83 Parts Identification - C13 Conventional Auger Mover ITEM PART NUMBER DESCRIPTION QTY. 811416 ELBOW-10 MORB X -8 MJIC, 90 DEG 812026 5/16" X 1" HEX BOLT (PL) 812362 5/16" LOCK NUT (PL) 812363 3/8" LOCK NUT (PL) 812364 1/2" LOCK NUT (PL) 812626 BOLT CARR 0.313NC X 1.00GR5PL 81546...
  • Page 84: Pump - C1352, C1362

    Parts Identification - C13 Conventional Auger Mover PUMP - C1352, C1362 11 10 18 19 DETAIL A 937042...
  • Page 85 Parts Identification - C13 Conventional Auger Mover ITEM PART NUMBER DESCRIPTION QTY. 811416 ELBOW-10 MORB X -8 MJIC, 90 DEG 812026 5/16" X 1" HEX BOLT (PL) 812362 5/16" LOCK NUT (PL) 812363 3/8" LOCK NUT (PL) 812364 1/2" LOCK NUT (PL) 812626 BOLT CARR 0.313NC X 1.00GR5PL 81546...
  • Page 86: Hydraulic Cylinder - Mover Lift - C1342

    Parts Identification - C13 Conventional Auger Mover HYDRAULIC CYLINDER - MOVER LIFT - C1342 938156 ITEM PART NUMBER DESCRIPTION QTY. 938157 CYLINDER-2.00” DIA, 36.75 TO 58.50 921099 ADAPTER-6MORB X -6MJIC R.047...
  • Page 87: Hydraulic Cylinder - Mover Lift - C1352, C1362

    Parts Identification - C13 Conventional Auger Mover HYDRAULIC CYLINDER - MOVER LIFT - C1352, C1362 929995 ITEM PART NUMBER DESCRIPTION QTY. 916438 CYLINDER-2.00” DIA, 36.75 TO 63.25 921099 ADAPTER-6MORB X -6MJIC R.047...
  • Page 88: Relief Valve

    Parts Identification - C13 Conventional Auger Mover RELIEF VALVE 935995...
  • Page 89 Parts Identification - C13 Conventional Auger Mover ITEM PART NUMBER DESCRIPTION QTY. 810761 5/16" X 2 1/2" HEX BOLT (PL) 812320 ADAPTER-8 MPT X -6 MJIC 812362 5/16" LOCK NUT (PL) 912909 VALVE-RELIEF , DOUBLE 913967 HOSE-6 X -6JIC X -6JIC 90 ELBOW - LENGTH = 12” 918981 ADAPTOR-08 FJIC X -06 MJIC 935678...
  • Page 90: Hoses

    Parts Identification - C13 Conventional Auger Mover HOSES OIL TANK LH WHEEL MOTOR MOVER PUMP AUGER LIFT CYLINDER RELIEF VALVE RH WHEEL MOTOR...
  • Page 91 Parts Identification - C13 Conventional Auger Mover MOVER LIFT CYLINDER STEERING CYLINDER BALL VALVE CONSOLE VALVE BLOCK...
  • Page 92 Parts Identification - C13 Conventional Auger Mover HOSES - C1342 ITEM DESCRIPTION LENGTH 936002 HOSE-6 X -6JIC X -6JIC 64” 936002 HOSE-6 X -6JIC X -6JIC 64” 913756 HOSE-8 X -8JIC X -8JIC 200” 913756 HOSE-8 X -8JIC X -8JIC 200”...
  • Page 93: Specifications

    Specifications - C13 Conventional Auger Mover SPECIFICATIONS PERFORMANCE DIMENSIONS HARDWARE TORQUE VALUES Metric Chart Imperial Chart HYDRAULIC CONNECTION SPECIFICATIONS O-Ring Fitting (Straight Thread) O-Ring Face Seal Connection Flare Fitting Port Seal (O-Ring Boss) Fitting Tube Lines And Hoses...
  • Page 94 Specifications - C13 Conventional Auger Mover...
  • Page 95 Specifications - C13 Conventional Auger Mover PERFORMANCE Model C1342 C1352 C1362 Engine Recommended CH980 Kohler 35 HP 3H50TIC Diesel Hatz Mover Wheel Wheel 15” X 4.5” Mover Hub Type 4-Bolt 4-Bolt 4-Bolt Mover Oil Tank Capacity Mover Oil Tank Filter DIMENSIONS Model C1342...
  • Page 96 Specifications - C13 Conventional Auger Mover HARDWARE TORQUE VALUES Metric Chart...
  • Page 97 Specifications - C13 Conventional Auger Mover Imperial Chart...
  • Page 98 Specifications - C13 Conventional Auger Mover HYDRAULIC CONNECTION Port Seal (O-Ring Boss) Fitting SPECIFICATIONS Port Seal And O-ring Boss Tightening Torque O-Ring Fitting (Straight Thread) Tube Line O.D. Thread Size N•m (ft-lb) 1/4” 7/16” - 20 13 (18) Lubricate the O-ring before installing the fitting. 3/8”...
  • Page 99: Warranty

    Warranty - C13 Conventional Auger Mover WARRANTY FARM KING BASE LIMITED WARRANTY Repair Parts Limited Warranty What Is Not Covered Authorized Dealer And Labor Costs Warranty Requirements...
  • Page 100 Warranty - C13 Conventional Auger Mover...
  • Page 101 If Farm King determines that it will pay labor costs for warranty work, it will do so by issuing a credit to the dealer’s or distributor’s account.
  • Page 102 Corrections of defects and improper workmanship in the manner, and for the applicable time periods, provided for herein shall constitute fulfillment of all responsibilities of Farm King to the purchaser, and Farm King shall not be liable in negligence, contract, or on any other basis with respect to the subject equipment.
  • Page 104 www.farm-king.com 301 Mountain Street South Morden, MB R6M 1X7 E-mail: info@buhler.com www.farm-king.com Equipment shown is subject to change without notice. ©2020 Buhler Trading Inc. Printed in Canada TSX:BUI a division of Buhler Industries Inc.

This manual is also suitable for:

13521362

Table of Contents