NuAire IAQ-PURGE Installation And Maintenance

NuAire IAQ-PURGE Installation And Maintenance

Purge ventilation unit

Advertisement

Quick Links

1.0 SAFETY INFORMATION

The provision of the electrical supply and the connection of the unit to the mains
must be carried out by a qualified electrician.
Isolate from power supply before removing any covers. During installation /
Maintenance ensure all covers are fitted before switching on the mains supply.
All-pole disconnection from the mains as shown in the wiring diagram must be
incorporated within the fixed wiring and shall have a minimum contact separation of
3mm in accordance with latest edition of the wiring regulations.
This unit must be earthed.
Ducting must be securely fixed with screws to the spigot to prevent access to live
parts. Duct runs terminating close to the fan must be adequately protected by
suitable guards.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
Precautions must be taken to avoid the back-flow of gases into the room from the
open flue of gas or other fuel-burning appliances.
This appliance should not be used by children or persons with reduced physical,
sensory or mental capabilities or lack of experience and knowledge, unless they
have been given supervision or instruction concerning the safe use of the appliance
by a person responsible for their safety. Children shall not play with the appliance.
Cleaning and user maintenance shall not be carried out by children.

2.0 INTRODUCTION

The IAQ-PURGE is designed to provide manually controlled purge
ventilation to rapidly dilute pollutants and/or water vapour. It may also
be used to improve thermal comfort.
The unit may be used for supply or extract, however, the different
applications will require variations to the completed installation e.g.
filtration, insulation. Contact Nuaire to discuss the full system design
requirements.
nuaire.co.uk
029 2085 8400
IAQ-PURGE
Purge Ventilation Unit
Installation and Maintenance
IMPORTANT
This appliance should not be used by children or persons with
reduced physical, sensory or mental capabilities or lack of
experience and knowledge, unless they have been given super-
vision or instruction concerning the safe use of the appliance
by a person responsible for their safety. Children shall not play
with the appliance. Cleaning and user maintenance shall not
be carried out by children.
01. 05. 19. Document Number 671874
The EMC Directive
2014/30/EU
The Low Voltage
Directive
2014/35/EU
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IAQ-PURGE and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for NuAire IAQ-PURGE

  • Page 1 Cleaning and user maintenance shall not be carried out by children. 2.0 INTRODUCTION IMPORTANT The IAQ-PURGE is designed to provide manually controlled purge This appliance should not be used by children or persons with ventilation to rapidly dilute pollutants and/or water vapour. It may also reduced physical, sensory or mental capabilities or lack of be used to improve thermal comfort.
  • Page 2 These should be integrated into the system design where The provision of the electrical supply and the connection of the unit appropriate and can be purchased from Nuaire if required. If to the mains must be carried out by a qualified electrician. All-pole...
  • Page 3 Installation and Maintenance IAQ-PURGE - Purge Ventilation Unit 5.2 Mounting Hole Dimensions Figure 2. Mounting Hole Dimensions 5.0 ELECTRICAL CONNECTION Figure 3. PCB IMPORTANT For good EMC practice, any sensor cable or switched live cables should not be placed within 50mm of, or on, the same metal cable tray as other cables.
  • Page 4 Installation and Maintenance IAQ-PURGE - Purge Ventilation Unit 5.2.1 Single Speed Wiring Figure 4. Prewired Connections Green / Yellow MAINS Blue 230 V 50 Hz Brown 2 Pole Fuse 2 A ON / OFF Isolator Switch 5.2.4 Single Speed Wiring with Mains Activated Back-draught Damper Figure 5.
  • Page 5 A calibrated moving vane anemometer and hood will be required to with Clause 14 of our Conditions of Sale. Customers purchasing from carry out commissioning. outside of the UK should contact Nuaire International Sales office for further details. Adjustment valves should be locked in place to prevent further adjustment.

Table of Contents