Saving A Scene (Scene); Saving The Tone Settings Of Each Part (Part1-4 Tone); Initializing The Scene (Scene Initialize); Initializing A Tone (Tone Initialize) - Roland Jupiter-Xm Reference Manual

Reference Manual Ver. 1.5 and later
6 .
To execute, press the [ENTER]
Saving a Scene
(SCENE)
Here's how to save the scene settings. If saving is needed, the screen
indicates "EDITED. "
If the PART 1–4 tones are indicated as
complete sound, save the tones first.
1 .
Press the [SCENE] button, and then press the
button .
2 .
Use the [1] knob to select
[ENTER] button .
3 .
Use the [2] knob to select the save-destination, and then
press the [ENTER] button .
If you want to rename the scene that you're saving, use the
[>] buttons to move the cursor, and use the
character.
4 .
Press the [ENTER] button .
A confirmation message appears.
If you decide to cancel, press the
5 .
To execute, press the [ENTER]
Saving the Tone Settings of Each Part
(PART1–4 TONE)
Here's how to save the tone settings of each part.
1 .
Press the [SCENE] button, and then press the
button .
2 .
Use the [1] knob to select
which the tone you're saving is assigned), and then press
the [ENTER] button .
3 .
Use the [1] knob or [2] knob
and then press the [ENTER]
If you want to rename the tone that you're saving, use the
[>] buttons to move the cursor, and use the
character.
4 .
Press the [ENTER] button .
A confirmation message appears.
If you decide to cancel, press the
5 .
To execute, press the [ENTER]
Initializing the Scene
Here's how to initialize the scene settings.
* Initializing the scene settings also initializes the tones of PART 1–4 at the same
time.
1 .
Press the [SCENE] button, and then press the
button .
2 .
Use the [1] knob to select
press the [ENTER] button .
42
button .
"EDITED, " and you want to save the
[WRITE]
"SCENE," and then press the
PAGE [<]
[2] knob to specify the
[EXIT] button.
button .
[WRITE]
"PART* TONE" (* is the part to
to select the save-destination,
button .
PAGE [<]
[2] knob to specify the
[EXIT] button.
button .
(SCENE INITIALIZE)
[WRITE]
"SCENE INITIALIZE," and then
Initializing a Tone
(TONE INITIALIZE)
Here's how to initialize the tone of the current part. The initialized state
differs depending on the model that is selected for that part.
You can't change the model later. You must first select a tone of the model
that you want to edit, and then execute Tone Initialize to initialize it.
1 .
Press the [SCENE] button, and then press the
button .
2 .
Use the [1] knob to select
the [ENTER] button .
Editing the System Settings
1 .
Press the [MENU] button .
2 .
Use the [1] knob to select
[ENTER] button .
You can also make this selection by using the
instead of the [1] knob.
3 .
Use the PAGE [<] [>] buttons
want to edit .
SYSTEM
Make basic device settings for the JUPITER-Xm.
&
"System Parameter List"
SYSTEM EFFECT: Cho
Choose whether the chorus effect settings are fixed at the system
settings, or are specified by each scene.
If "Source" is set to "SCENE, " use the scene effect parameters to edit the
effect.
&

"Editing the System Settings (System)"

SYSTEM EFFECT: Dly
Choose whether the delay effect settings are fixed at the system
settings, or are specified by each scene.
If "Source" is set to "SCENE, " use the scene effect parameters to edit the
effect.
&
"Editing the System Settings (System)"
SYSTEM EFFECT: Rev
Choose whether the reverb effect settings are fixed at the system
settings, or are specified by each scene.
If "Source" is set to "SCENE, " use the scene effect parameters to edit the
effect.
&
"Editing the System Settings (System)"
SYSTEM EQ / COMP
Edit the equalizer and compressor settings.
4 .
Use the [1] knob to select the parameter and use the
knob to change the setting .
For details, refer to "Parameter Guide"
5 .
If you want to save the settings, perform the system write
operation .
Saving the System Settings
Here's how to save the system settings.
1 .
In the SYSTEM screen, press the
The SYSTEM WRITE screen appears.
If you decide to cancel, press the
[WRITE]
"TONE INITIALIZE," and then press
(System)
"SYSTEM," and then press the
PAGE [ ] [ ] buttons
to select the page that you
(p. 43)
(p. 42)
(p. 42)
(p. 42)
(PDF).
(System Write)
[WRITE] button .
[EXIT] button.
[2]