Table of Contents
Advertisement
Quick Links
HD200 Series Ice Dispenser
Installation & Operation Manual
Kold-Draft International, LLC
1525 East Lake Road
Erie, PA 16511-1088 U.S.A.
Phone: (800) 840-9577
Fax: (800) 548-9392
www.kold-draft.com
This manual is updated periodically. Visit http://www.kold-draft.com/resources/literature.php for the latest version.
Advertisement
Table of Contents
Related Manuals for Kold-Draft HD200 Series
Summary of Contents for Kold-Draft HD200 Series
- Page 1 HD200 Series Ice Dispenser Installation & Operation Manual Kold-Draft International, LLC 1525 East Lake Road Erie, PA 16511-1088 U.S.A. Phone: (800) 840-9577 Fax: (800) 548-9392 www.kold-draft.com This manual is updated periodically. Visit http://www.kold-draft.com/resources/literature.php for the latest version.
- Page 2 KOLD-DRAFT INTERNATIONAL, LLC A DIVISION OF THE LEGACY COMPANIES, LLC Installation & Operation Manual HD200 Series Ice Dispenser Copyright 2017 KOLD-DRAFT INTERNATIONAL, LLC Unauthorized reproduction of this manual is freely permitted for all purposes except for monetary gain. It is not guaranteed that this service manual is up to date, technically correct, complete, or free from writing problems or that the product is free from minor flaws or that it meets the needs of the customer.
-
Page 3: Safety Warnings And Information
Contact the freight carrier immediately to report any damage and file a claim. Have carrier note the damage on the bill of lading. Call Kold-Draft with your claim number to arrange replacement or repair. Read the entire manual before installing, operating or servicing the machine. - Page 4 Ice Dispenser Identification Model Number Key Electrical Characteristics 1 = 115 volt-60 hz.-1ph. (2-wire plus ground) 4 = 208/230 volt-60 hz.-1ph. (2-wire plus ground) 7 = 220/240 volt-50 hz.-1ph. (2-wire plus ground) Modification Code 0 = No Modifications Series 2 = 200 Series Model Family Date Code Key HD = Ice Dispenser...
-
Page 5: Installation Information
Placing equipment in these locations will result in increased ice meltage. Unpacking Unpacking a KOLD-DRAFT ice dispenser can be done by prying off the boards that are holding the cardboard box to the shipping pallet. The box can then be lifted vertically to expose the machine. -
Page 6: Installation Requirements
Installation Requirements The ice dispenser must be installed indoors and the location should be free of airborne contaminates including any corrosive elements. Note: Consult ice machine instructions for proper installation requirements, before determining the location of the ice dispenser. Installation site ambient temperatures below 90°F (32°C) are recommended for proper operation. - Page 7 WARNING: Always disconnect power before servicing. • All KOLD-DRAFT models are intended to be installed with a permanent connection to the field electrical supply. See rating plate on the back of the machine for power supply requirements.
- Page 8 Dispenser Construction and Operation The HD200 series dispenser consists of an ice storage bin with an outlet spout, a motorized stirring bar to keep the ice from bridging in the bin and to move ice to the outlet spout when dispensing and an operating ice stop in the spout opening to deflect ice past the spout during agitation cycles and allow ice out when dispensing.
- Page 9 Wiring Diagram HD200 ICE DISPENSER 507 1092 01 REV. D...
-
Page 10: Maintenance And Service Information
Maintenance and Service Information Ice Dispenser Cleaning Procedure It is recommended to perform this cleaning procedure a minimum of twice per year Note: The frequency of the need for cleaning is determined by the supply water characteristics. The dispenser should be cleaned no less than once every 6 months and it may require more frequent cleaning. -
Page 11: Storage And Winterization
Storage and Winterization Remove all ice from the dispenser, disconnect the electric power supply and clean and sanitize the dispenser. Removal from service When the ice dispenser is determined to be no longer useable, please be sure that it is rendered safe for storage or disposal. -
Page 12: Problems And Solutions
Problems and Solutions PROBLEM POSSIBLE CAUSE SOLUTION Dispenser not operating No Power to Dispenser Reset Circuit Breaker or Replace Fuse If the Agitation Motor Does Not Turn for a Few Seconds at the Initiation of Power to the Dispenser or Periodically Replace Agitation Timer Thereafter, But Does Turn When the Ice Button is Pushed, the Agitation Timer... - Page 13 DISPENSER PARTS LIST 302143201 HD200 FRONT COVER 511119601 HD200 DRIVE BEARING 302141801 HD200 TOP CAP 302141701 HDX200 FRONT COVER 301185701 HD200 REAR COVER 207100101 HD200 STIRRING BAR ASSEM. 505119301 HD200 SINK 102103701 RELAY-PLUG IN 102103801 RELAY-PLUG IN 220V 102100701 RELAY SOCKET (EAGLES, GB 400R & 102124101 CAPACITOR 4MFD.
Need help?
Do you have a question about the HD200 Series and is the answer not in the manual?
Questions and answers