Advertisement
Quick Links
CLASSIC
GT357
KOLD-DRAFT
®
Installation & Operation Instructions
KOLD-DRAFT
®
Ice Machine Products
1525 East Lake Road, Erie, PA 16511-1088, U.S.A.
Phone: 814-453-6761
A Tradition of Excellence In Ice Equipment.
FAX: 814-455-6336
©2004 KDIndustries, Inc., Erie, PA, U.S.A.
Printed in U.S.A.
3/04
508 1015 02 English with SI Units
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Kold-Draft GT357 Classic
Summary of Contents for Kold-Draft GT357 Classic
- Page 1 CLASSIC GT357 KOLD-DRAFT ® Installation & Operation Instructions KOLD-DRAFT ® Ice Machine Products 1525 East Lake Road, Erie, PA 16511-1088, U.S.A. Phone: 814-453-6761 A Tradition of Excellence In Ice Equipment. FAX: 814-455-6336 ©2004 KDIndustries, Inc., Erie, PA, U.S.A. Printed in U.S.A.
- Page 2 INSTALLATION AND OPERATION INSTRUCTIONS FOR KOLD-DRAFT GT300 SERIES ICE CUBERS ® CLASSIC ® CHECK FOR FREIGHT DAMAGE BEFORE PROCEEDING: Even though damage to the carton may not have been evident, check for hidden damage and contact freight carrier immediately if necessary to file a claim.
- Page 3 CAUTION: RISK OF PERSONAL INJURY OR EQUIPMENT DAMAGE. Use a suitable lifting means and be careful of sharp edges. 1. Remove the cabinet panels. NOTE: When re-installing the panels, be sure that the screws engage the TOP panel. 2. Remove the ice chute/drain pan. Drain tube assembly is packed with the drain pan as shown below .
- Page 4 7. Purge the potable water supply line. 8. Remove the water plate shipping strap. 9. Route the bin thermostat capillary tube through the grommet in the right end frame wall and under the ice chute. See the diagram below: 508101502 Rev: 10-5-98 - 4 -...
- Page 5 INSTALLATION SPECIFICATIONS READ THE FOLLOWING NOTES CAREFULLY PRIOR TO MAKING CONNECTIONS CAUTION: RISK OF PROPERTY DAMAGE, EQUIPMENT FAILURE, OR FIRE. Failure to comply with all installation specifications and instructions may cause erratic operation and the risk of damage or fire. REQUIREMENTS Electrical: THE INSTALLER MUST PROVIDE REQUIRED BRANCH CIRCUIT OVERCURRENT...
- Page 6 START-UP INSTRUCTIONS WATER LEVELS, CYCLE TIMES, AND REFRIGERANT CHARGES MODEL NUMBER GT357 C/HK Water fill level (Top of tank to level in control tube,cm) Approximate cycle time, min. Approximate harvest weight, kg. Refrigerant Charge, grams (R-404a) Air cooled: Liq. cooled: CAUTION: REFRIGERANT CHARGES MUST BE ACCURATELY WEIGHED.
-
Page 7: Preventative Maintenance
the bottom edge, replace the TOP panel, and finally secure all the panels with (2) screws in the TOP-SIDES of the machine. 8. Discard ice from start-up cycles, then clean and sanitize the bin following the instructions provided with the bin. 9. - Page 8 Clean up splashes or spillage immediately. Follow these instructions exactly. 1. Mix 1/2 bag of KOLD-DRAFT ice machine cleaner (55R-01000) in one (1) liter of clean, warm water (82°C. MAX.). 2. If the cuber is operating, wait until a harvest cycle occurs then trip the "ICE-OFF-WASH"...
- Page 9 ICE BIN CLEANING INSTRUCTIONS The bin should be cleaned periodically. If bin drain has any horizontal run, remove ice around the drain fitting and flush with two liters of hot water monthly. (Long drain lines should be flushed weekly.) CAUTION: RISK PERSONAL INJURY,...
- Page 10 508101502 Rev: 10-5-98 - 10 -...
Need help?
Do you have a question about the GT357 Classic and is the answer not in the manual?
Questions and answers