Suzuki GRAND VITARA 2005 Manual page 27

Standard Tightening Torque
Each fastener should be tightened to the torque specified in each section of this manual. If no description or
specification is provided, refer to the following tightening torque chart for the applicable torque for each fastener. When
a fastener of greater strength than the original one is used, however, use the torque specified for the original fastener.
NOTE
• For the flanged bolt, flanged nut and self-lock nut of 4T and 7T strength, add 10% to the tightening
torque given in the following chart.
• The following chart is applicable only where the fastened parts are made of steel light alloy.
Tightening torque chart
Strength
A equivalent of 4T strength fastener
A equivalent of 6.8 strength
fastener without flange
A equivalent of 6.8 strength
fastener with flange
*: Self-lock nut (6 strength)
A equivalent of 7T strength fastener
A equivalent of 8.8 strength bolt (8
strength nut) without flange
A equivalent of 8.8 strength bolt (8
strength nut) with flange
Unit
4
N⋅m 1.5
kgf-m 0.15
lb-ft 1.0
I1SQ01010004-01
N⋅m 2.4
kgf-m 0.24
lb-ft 2.0
I1SQ01010005-01
N⋅m 2.4
kgf-m 0.24
lb-ft 2.0
I1SQ01010006-01
N⋅m 2.3
kgf-m 0.23
lb-ft 2.0
I1SQ01010007-01
N⋅m 3.1
kgf-m 0.31
lb-ft 2.5
I1SQ01010008-01
N⋅m 3.2
kgf-m 0.32
lb-ft 2.5
I1SQ01010009-01
Thread Diameter (Nominal Diameter) (mm)
5 6 8 10
3.0 5.5 13 29
0.30 0.55 1.3 2.9
2.5 4.0 9.5 21.0
4.7 8.4 20 42
0.47 0.84 2.0 4.2
3.5 6.0 14.5 30.5
4.9 8.8 21 44
0.49 0.88 2.1 4.4
3.5 6.5 15.5 32.0
4.5 10 23 50
0.45 1.0 2.3 5.0
3.5 7.5 17.0 36.5
6.3 11 27 56
0.63 1.1 2.7 5.6
4.5 8.0 19.5 40.5
6.5 12 29 59
0.65 1.2 2.9 5.9
5.0 9.0 21.0 43.0
General Information:
12 14 16
45 65 105
4.5 6.5 10.5
32.5 47.0 76.0
80 125 193
8.0 12.5 19.3
58.0 90.5 139.5
84 133 203
8.4 13.3 20.3
61.0 96.5 147.0
85 135 210
8.5 13.5 21
61.5 98.0 152.0
105 168 258
10.5 16.8 25.8
76.0 121.5 187.0
113 175 270
11.3 17.5 27
82.0 126.5 195.5
0A-5
18
160
16.0
116.0
280
28.0
202.5
298
29.8
215.5
240
24
174.0
373
37.3
270.0
395
39.5
286.0