Maintenance - Bosch DAS 3000 S20 Original Instructions Manual

(3) Recess in spacer
(4) Spirit level
---
6.

Maintenance

6.1 ---Separator--- Cleaning
Coarse workshop rags and abrasive cleaning
agents may damage the DAS 3000 S20 .
 Use only neutral cleaning agents and soft cloths to
clean the DAS 3000 S20.
---Separator---
6.2 Spare parts
Denomination
<)
Rubber buffer (2x) on brake
Star knob screws (2x) for attaching the "Multi-
<)
Target-Shop" box
Hammer nuts (2x) for the top camera's
<)
mount
Camera beam (without cameras)
Yellow protective caps (2x) for the camera
beam
Indicator bar with slide
Left slide (as viewed from the front) on the
<)
indicator bar
Right slide (as viewed from the front) on the
<)
indicator bar
Yellow protective caps (2x) for the indicator
<)
bar
End caps (2x) for the slide guide on the indi‐
<)
cator bar
<)
Retaining cable
Rubber magnets on the indicator bar
Spirit level on the indicator bar
Left positioning bar (as viewed from the
front)
Right positioning bar (as viewed from the
front)
Slider (2x) for the positioning bar
Star handles (5x) suitable for vertical posi‐
tions A, B, C, D, radar position R, R position,
<)
Z position
Star handles (2x) suitable for securing the po‐
<)
sitioning bar
Star handle (1x) suitable for securing at the R
<)
position and Z position
<)
T slot nut (2x) for the slider
Left tape measure for the height of the indica‐
tor bar (as viewed from the front)
Right tape measure for the height of the indi‐
cator bar (as viewed from the front)
<)
Cable carrier
Calibration board CTA 300-1 for front camera
systems and front radar systems
<)
Mounting adapter 1 (2x)
Robert Bosch GmbH
Order number
1 688 990 086
1 686 621 080
3 842 530 283
1 682 391 559
1 683 212 042
1 682 329 109
1 688 030 217
1 688 030 215
1 683 212 041
1 683 212 040
1 684 712 028
1 688 120 188
1 687 233 114
1 688 040 326
1 688 040 323
<) 3 842 552 424
1 686 621 078
1 686 621 077
1 686 621 081
3 842 528 735
1 687 233 119
<)
1 687 233 117
<)
3 842 555 180
1 681 098 011
1 685 720 380
Denomination
<)
Mounting adapter R (1x)
Wheel holder CTA 100-1
<)
Reference board CTA 400-1
Wheel holder CTA 100-1 star handle
Wheel holder CTA 100-1 spacers (2x)
Wheel holder CTA 100-1 prongs (2x)
Wheel holder CTA 100-1 top bracket parts set
Reference board CTA 400-1 fastening parts
set
Contact plate CTA 104-1
Contact plate CTA 104-1 edge protection
Left offset ruler (as viewed from the front)
Right offset ruler (as viewed from the front)
Rubber grommets (4x) for the parked position
<)
of wheel holder CTA 400-x
Rubber buffers (2x) for the parked position of
<)
wheel holder CTA 400-x
---
<)
Wearing parts
---
6.3 Replacing the positioning bar
(1)
1. Remove the front cover
(1) Front cover
2. Loosen the knurled screws
height of the positioning unit (2).
3. Push the positioning unit
protection frame.
DAS 3000 S20 | 33 | en
Order number
1 685 720 384
1 688 120 190
1 681 098 013
1 686 621 083
1 687 016 229
1 687 016 230
1 687 016 228
1 687 010 635
1 681 320 090
1 687 010 742
<)
1 688 132 049
1 688 132 050
1 680 212 064
1 688 990 087
on the frame.
1
(3)
for adjusting the
(2)
up and out of the edge
1 689 989 485 | 2020-08-01