allen MSP450A Operations & Parts Manual
  1. Manuals
  2. Brands
  3. allen Manuals
  4. Trowels
  5. MSP450A
  6. Operations & parts manual

allen MSP450A Operations & Parts Manual

Riding trowel
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATIONS-PARTS
MANUAL
ALSO INCLUDES 450C
05/2016
Riding Trowel
061090 - 12/2013

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MSP450A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for allen MSP450A

Summary of Contents for allen MSP450A

  • Page 1 OPERATIONS-PARTS MANUAL ALSO INCLUDES 450C 05/2016 Riding Trowel 061090 - 12/2013...
  • Page 2 This manual, or a copy of it, must be kept with the machine at all times. There is a manual storage container located on the machine for your convenience. 061090 - 12/2013...
  • Page 3 Allen Engineering Corporation (AEC). AEC assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual.
  • Page 4 Allen reserves the choice to repair or replace. 2. If Allen chooses to replace the part, it will be at no cost to the customer and will be made available to the Allen Distributor, Dealer, or Rental Center from whom the End User purchased the product.

  • Page 5: Table Of Contents

    Table of Contents Title Page Limited Warranty Table of Contents Information Contained In This Manual Dealer Information Ordering Parts Model Number - Serial Number Codes viii Unit Identifi cation Technical specifi cations Engine Specifi cations Machine Dimensional Specifi cations Section 1 - Safety State Regulations Federal Regulations Safety Information...

  • Page 6: Table Of Contents

    Table of Contents - Continued Title Page Parts Factory Service Information Replacement Part Procedure Seat Frame Assembly Right Rotor Assembly Left Rotor Assembly 4-10 Right Spider Assembly 4-12 Left Spider Assembly 4-13 Right Gearbox Assembly 4-14 Left Gearbox Assembly 4-16 Pitch Control Assembly 4-18 Kill Switch Pedal Assembly...

  • Page 7: Information Contained In This Manual

    Complete any warranty requirements as specifi ed by the engine manufacturer in their instructions found inside the manual box located on the operator’s control panel. Your engine is not manufactured by Allen Engineering Corporation, Inc, and therefore is not covered under Allen Engineering Corporation, Inc warranty.

  • Page 8: Dealer Information

    Dealer Information Your Dealer has Allen Engineering Corporation trained mechanics and original Allen replacement parts. Always contact the Allen Dealer who sold you this machine for Allen Certifi ed repairs and replacement parts. Place Allen Dealer information below for future reference.

  • Page 9: Ordering Parts

    Ordering Parts Section 4.0 contains illustrated parts lists for help in ordering replacement parts for your machine. Fol- low the instructions below when ordering parts to insure prompt and accurate delivery: All orders for service parts - include the serial number for the machine. Shipment will be delayed if this information is not available.

  • Page 10: Model Number - Serial Number Codes

    Model Number - Serial Number Codes Manufacturer’s Codes: When ordering parts or requesting service information, you will always be asked to specify the model and serial numbers of the machine. The legends below specifi cally defi nes each signifi cant character or group of characters of the Model Number and Serial Number codes.

  • Page 11: Unit Identifi Cation

    Unit Identifi cation Unit Identifi cation Plate Location: An identifi cation plate listing the model number and the serial number is attached to each unit and is located on the bottom left hand corner of the operator control panel. See image below for serial number plate number location.

  • Page 12: Technical Specifi Cations

    The MSP450 is our newest model in our popular MSP Series. The powerful diesel engine, Super Heavy-Duty Gearboxes and Spiders provide a great weight-to-horsepower performer for larger con- tractors. The newly designed Allen power transmission system (patent pending) is incorporated into this machine to provide exceptional performance from the engine to the concrete surface.

  • Page 13: Engine Specifi Cations

    Engine Specifi cations 44 HP Kubota Model V1505-T-E4B Emission Regulation Tier 4 / Stage IIIA Type Vertical 4-cycle liquid cooled Diesel Number of Cylinders Bore mm (in) 78.0 (3.07) mm (in) 78.4 (3.09) Stroke Displacement L (cu.in) 1.498 (91.41) Combustion System Intake System Turbocharged Maximum Speed...
  • Page 14 Dimensional Specifi cations 061090 - 12/2013 Page xii...
  • Page 15 CE Documentation The Technical Construction fi le is maintained at: Allen Engineering Corporation 819 South 5th St. Paragould, AR 72450 Telephone: 800-643-0095 Facsimile: 800-643-0097 The authorized representative is: ab lin-pro Mr. Thomas Voeler Femvägsskälet 3 421 50 Västra Frölunda Sweden...
  • Page 16 INTENTIONALLY BLANK 061090 - 12/2013 Page xiv...

  • Page 17: Section 1 - Safety

    SECTION 1 SAFETY Section 1 SAFETY Page 1-1 061090 - 12/2013...

  • Page 18: State Regulations

    State Regulations SECTION 1 Proposition 65 Warning SAFETY Page 1-2 061090 - 12/2013...

  • Page 19: Federal Regulations

    Federal Regulations SECTION 1 Respiratory Hazards SAFETY Page 1-3 061090 - 12/2013...

  • Page 20: Safety Information

    Safety Information SECTION 1 SAFETY Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the safety mes- sages and operating instructions could result in injury to yourself and others. SAFETY NOTES The four safety notes shown below will inform you about potential hazards that could injure you or oth- ers.
  • Page 21 Safety Symbols SECTION 1 SAFETY Potential hazards associated with the operation of this equipment will be referenced with hazard symbols which may appear throughout this manual in conjunction with safety notes. Page 1-5 061090 - 12/2013...

  • Page 22: General Safety

    General Safety SECTION 1 SAFETY ● NEVER operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices required by the job or city and state regulations. ● ALWAYS avoid wearing jewelry or loose fi tting clothes that may snag on the controls or moving parts as this can cause serious injury.
  • Page 23 General Safety (cont’d) SECTION 1 SAFETY ● ALWAYS know the location of the nearest phone or keep a phone on the job site. Also, know the phone numbers of the nearest ambulance, doctor and fi re department. This information will be invalu- able in the case of an emergency.
  • Page 24 General Safety (cont’d) SECTION 1 SAFETY ● ALWAYS keep the machine in proper running condition. ● Fix damage to machine and replace any broken parts immediately. ● ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel.
  • Page 25 General Safety (cont’d) SECTION 1 SAFETY ● DO NOT start the engine near spilled fuel or combustible fl uids. Fuel is extremely fl ammable and its vapors can cause an explosion if ignited. ● ALWAYS refuel in a well-ventilated area, away from sparks and open fl ames. ●...
  • Page 26 General Safety (cont’d) SECTION 1 SAFETY ● ALWAYS recharge the battery in a well-ventilated environment to avoid the risk of a dangerous con- centration of combustible gases. ● If the battery liquid (dilute sulfuric acid) comes into contact with clothing or skin, rinse skin or clothing immediately with plenty of water. ●...
  • Page 27 Safety Labels and Decals SECTION 1 SAFETY This decal notates special safety equipment that is required to operate this machine. This decal notates the pinch point locations on this machine. This decal notates the lifting points on this machine. This decal indicates that this machine can start fi...

  • Page 28: Safety Labels And Decals

    This decal notates that the thrust bearings must be greased daily. This decal notates that this product was made at the Allen Engineering Corporation manufacturing facilities in Paragould, Arkansas. This decal notates the location of the 12V accessory port.
  • Page 29 Safety Labels and Decals (cont’d) SECTION 1 SAFETY This decal notates that this product is covered under one or more patents. This decal notates the model number and series number of this machine. This decal notates the location of where to put hand tools on the machine.
  • Page 30 Safety Labels and Decals (cont’d) SECTION 1 SAFETY This decal notates the location of where the operations and parts manuals are. This decal illustrates Allen Concrete Equipment. Page 1-14 061090 - 12/2013...
  • Page 31 Transportation Safety SECTION 1 SAFETY ● When lifting the riding trowel, all personnel must be clear of the machine. ● DO NOT stand near or under the machine while it is being lifted. Lifting instructions using a hoist: ● Place slings, chains or hooks through each lifting eye on the machine. Use a sling or chains with a minimum length of 2 meters (5 feet) on each leg, connected to a central lifting device.

  • Page 32: Transportation Safety

    1.4 Transportation Safety (cont’d) SECTION 1 SAFETY ● Make sure the hitch and coupling of the towing vehicle are rated equal to, or greater than the trailer “gross vehicle weight rating.” ● ALWAYS inspect the hitch and coupling for wear. Never tow a trailer with defective hitches, couplings, chains, etc.

  • Page 33: Section 2 - Operations

    SECTION 2 OPERATIONS Section 2 OPERATIONS Page 2-1 061090 - 12/2013...

  • Page 34: Pre-Operating Instructions

    Pre-Operating Instructions SECTION 2 OPERATIONS Before operation each day ensure the following: • All guards, side screens and panels are in place. • All safety and information signs are in place and legible. • Engine oil levels are correct. • Check battery level •...
  • Page 35 Pre-Operating Instructions - cont’d SECTION 2 OPERATIONS Before starting riding trowel, locate and identify the operational and visual controls pertaining to the operation of the riding trowel. 1) Sit down correctly on the riding trowel seat. DO NOT attempt to start the riding trowel without an operator in the seat.

  • Page 36: Operating

    SECTION 2 OPERATIONS To utilize your Allen Engineering MSP450 Rider to its fullest capacity the machine should be driven in the direction the operator is facing. This will fi nish the widest possible area while giving the operator an excellent view of the slab surface about to be troweled. When the machine reaches the end of the slab make a 180 degree turn and repeat the straight line of direction to the other end of the slab.
  • Page 37 Operating Instructions SECTION 2 OPERATIONS With the operator in the seat, show them the functions of the joysticks [B] and [C] and how to start the machine. A hard level concrete slab with water on the surface is an ideal place for an operator to practice with the machine.
  • Page 38 Operating Instructions - cont’d SECTION 2 OPERATIONS Steering The Riding Trowel A slight “feathering motion” forward and backward with the left hand joystick is required to move the machine in a straight path to the left or right while operating the right hand joystick. Position Action Forward...
  • Page 39 Operating Instructions - cont’d SECTION 2 OPERATIONS Pitch Adjustment Different pitch angles are needed as you work the different stages of the concrete. Refer to fi gure be- low. When changing or setting pitch (angle of trowel blades), slow the machine down, set the desired degree of pitch on the left side of the machine and then adjust the right side to match.
  • Page 40 OUR QUALITY POLICY The Allen Engineering Team is fully committed to exceeding customer expectations for the quality of the products and services provided through the continuous improvement process of reducing waste, defects, and variability in everything we do.

  • Page 41: Section 3 - Service

    SECTION 3 SERVICE Section 3 SERVICE Page 3-1 061090 - 12/2013...

  • Page 42: Maintenance Instructions

    Maintenance Instructions SECTION 3 SERVICE Maintenance described in this section represents minimum requirements for continuous satisfactory operation of the machine. Because improperly maintained machines are hazardous, it is extremely important that only qualifi ed mechanics perform maintenance work. It is imperative that only genuine AEC parts are used if replacement is needed as substituted parts in critical areas may place the operator at risk and impeed correct machine performance.
  • Page 43 Air Filter Maintenance SECTION 3 SERVICE Pre-Cleaner Maintenance Procedure This machine is equipped with a large capacity, dual element air fi lter. When should you change an air fi lter? Many people believe that if a fi lter looks dirty it is no longer working and should be changed.
  • Page 44 Kubota Engine Maintenance Schedule SECTION 3 SERVICE Hour Meter Reading: After Purchase Check or Change Every Interval Shown Below 1000 Engine oil & fi lter change Transmission fl uid change Hyd. Oil fi lter cleaning Greasing ALL zerks Clean air cleaner element Clean radiator screen and check coolant level Fan belt tension...
  • Page 45 Kubota Engine Oil Maintenance SECTION 3 SERVICE Engine Oil Level Check • ALWAYS check the engine oil dipstick before using the riding trowel. At a minimum check engine oil once per day. Follow the Maintenance and Lubrication Chart contained herein. •...

  • Page 46: Maintenance Schedule

    Periodic Maintenance Schedule SECTION 3 SERVICE Maintenance Schedule Item Daily Weekly Monthly Annually 100 Hours  Check external hardware  Apply grease to thrust bearings  Check all operational controls  Tighten all bolts and nuts.  Grease steering assembly heim joints ...

  • Page 47: Filter Replacement

    Filter Replacement SECTION 3 SERVICE PRIMARY AIR CLEANER ELEMENT PART #: P822686 ENGINE OIL FILTER PART #: 16271-32090 ENGINE FUEL FILTER PART #: 24 050 13 Page 3-7 061090 - 12/2013...
  • Page 48 Engine Oil and Oil Filter SECTION 3 SERVICE 1. Refer to the chart on page 3-4 for engine oil change maintenance. 2. Remove the oil fi ller cap and fi ll engine crankcase with recommended type oil as listed in the table below.
  • Page 49 Engine Fuel Filter SECTION 3 SERVICE 70000-43081 Refer to the chart on page 3-4 for engine fuel fi lter change schedule. Refer to your engine manual for specifi c details to perform this operation. Check the oil and fuel lines and connections regularly for leaks or damage. Repair or replace as necessary.
  • Page 50 Battery and Charging System SECTION 3 SERVICE Mishandling of the battery shortens its service life and adds to maintenance cost. 1. Check and clean battery terminals for corrosion often. 2. Check the battery regularly and make sure that each electrolyte level is to the bottom of the vent well.
  • Page 51 Bearing Lubrication SECTION 3 SERVICE Driveline bearings require lubrication daily. Lubricate all bearing grease fi ttings with EP3 grease or equivalent. Failure to lubricate bearing grease fi ttings daily will cause rotation of driveshafts to stiffen. To prevent contamination of the bearing, always insert cap onto zerk fi...

  • Page 52: Troubleshooting

    Troubleshooting SECTION 3 SERVICE Possible Corrective Area Malfunction Ref. Cause Measure Battery is discharged - Add battery fl uid - Charge the battery - Replace the battery Battery cable is disconnected - Connect battery cable Blown fuse - Replace fuse Bad connection or breakage in the wiring - Contact your AEC dealer Engine does not start,...
  • Page 53 Troubleshooting - cont’d SECTION 3 SERVICE Possible Corrective Area Malfunction Ref. Cause Measure Bad fuel - Change fuel Clogged air cleaner - Clean or replace the air cleaner Black smoke comes out of exhaust Choke is not fully open - Open the choke fully Engine Other (other than above) - Contact your AEC dealer...
  • Page 54 Belt Tensioning SECTION 3 SERVICE These tolerances are for reference only. For fixed center drive applications Standard Belt Tensioning Procedure and special tolerances, contact Gates Power Transmission Product When installing a Gates belt: Application. A. Be sure it is tensioned adequately to prevent tooth jumping (ratcheting) under the most severe load conditions which the drive will encounter during operation.
  • Page 55 Belt Tensioning - cont’d SECTION 3 SERVICE Because of the high performance capabilities of PowerGrip belts, it is pos- STEP 3: Applying the tension. sible to design drives that have significantly greater load than are neces- sary to carry the actual design load. Consequently, Formula 14 can pro- Force deflection tension method vide Tst values less than are necessary for the belt to operate properly, A.
  • Page 56 OUR QUALITY POLICY The Allen Engineering Team is fully committed to exceeding customer expectations for the quality of the products and services provided through the continuous improvement process of reducing waste, defects, and variability in everything we do.

  • Page 57: Parts

    SECTION 4 PARTS Section 4 PARTS Page 4-1 061090 - 12/2013...

  • Page 58: Factory Service Information

    Factory Service Information SECTION 4 PARTS This section contains the illustrated drawings and parts list for help in identifying and/or ordering re- placement parts for your machine. Follow the instructions in the front section of this manual “Ordering Parts” when ordering replacement parts to insure prompt and accurate delivery. The FRONT and/or REAR orientations are defined from the operator’s view of sitting on machine (SOM).

  • Page 59: Replacement Part Procedure

    Replacement Parts Procedures SECTION 4 PARTS We recommend AEC quality replacement parts, available from the AEC Customer Service Department or your nearest AEC Dealer. Part numbers are subject to change without notice. Part numbers might be different outside of the United States of America.

  • Page 60: Seat Frame Assembly

    Seat Frame Assembly SECTION 4 Illustration PARTS Page 4-4 061090 - 12/2013...
  • Page 61 Seat Frame Assembly SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION 010081 FSTN, FW 1/4 010083 FSTN, FW 3/8 FSTN, NUT HEX 3/8-16 010102 PIN, Ø1/16 X 1 ZP STL COTTER 010131 FSTN, NUT NYLOK 3/8-16 010464 010572 FSTN, SCREW 8-32 X 3/8 SCR, 10-24x1/2 RDH PPH 013484 PIVOT, THROTTLE CABLE...
  • Page 62 Seat Frame Assembly (cont’d) SECTION 4 Illustration PARTS Page 4-6 061090 - 12/2013...
  • Page 63 DECAL, LIGHTS (SP) 053452 DECAL, 12V ACCESSORY (SP) 053454 DECAL, MANUALS (SP) 056338 DECAL AEC 1.5” X 3.25” WHITE/RED 056339 DECAL, 13.35” X 8” ALLEN OVAL 056920 MAGNETIC LATCH 060842 SEAT FRAME WMNT 060850 DOOR WMNT 060857 FRONT SCREEN ASSEMBLY...

  • Page 64: Right Rotor Assembly

    Right Rotor Assembly - 048957 SECTION 4 Illustration PARTS GREASE THRUST BEARING DAILY!!! TORQUE TO 85 Ft/lbs Page 4-8 061090 - 12/2013...
  • Page 65 Right Rotor Assembly - 048957 SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION FSTN, HHCS 5/16-18 X 2 GR 5 010024 FSTN, HHCS 3/8-16 X 1 010036 FSTN, LW 5/16 010090 010091 FSTN, LW 3/8 010095 FSTN, LW 5/8 010513 FITTING, 1/4-28 STR GREASE FSTN, NUT HEX NYLOCK 5/16-18...

  • Page 66: Left Rotor Assembly

    Left Rotor Assembly - 048956 SECTION 4 Illustration PARTS GREASE THRUST BEARING DAILY!!! TORQUE TO 85 Ft/lbs Page 4-10 061090 - 12/2013...
  • Page 67 Left Rotor Assembly - 048956 SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION FSTN, HHCS 5/16-18 X 2 GR 5 010024 FSTN, HHCS 3/8-16 X 1 010036 FSTN, LW 5/16 010090 010091 FSTN, LW 3/8 010095 FSTN, LW 5/8 010513 FITTING, 1/4-28 STR GREASE FSTN, NUT HEX NYLOCK 5/16-18...

  • Page 68: Right Spider Assembly

    Right Spider Assembly - 040795 SECTION 4 Illustration and Parts List PARTS ITEM PART NO. DESCRIPTION 010050 NUT, 1/2-13 JAM HEX 015682 WASHER, 3/8 EXT TOOTH LOCK 015683 BOLT, 3/8-16 X 7/8 DOG PT HEX HD CAP 015684 NUT, 3/8-16 JAM HEX 015686 FSTN, SQHSS 3/8-16 X 1 024755...
  • Page 69 Left Spider Assembly - 040794 SECTION 4 Illustration and Parts List PARTS ITEM PART NO. DESCRIPTION 010050 NUT, 1/2-13 JAM HEX 015682 WASHER, 3/8 EXT TOOTH LOCK 015683 BOLT, 3/8-16 X 7/8 DOG PT HEX HD CAP 015684 NUT, 3/8-16 JAM HEX 015686 FSTN, SQHSS 3/8-16 X 1 024755...

  • Page 70: Right Gearbox Assembly

    Right Gearbox Assembly - 037655 SECTION 4 Illustration PARTS Page 4-14 061090 - 12/2013...
  • Page 71 Right Gearbox Assembly - 037655 SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION OIL, MOBILE SHC 634 GEAR .75 GAL 001004 010037 FSTN, HHCS 3/8-16 X 1-1/4 GR 5 BOLT, 3/8-16x1-1/2 GR 5 HHCS 010038 WSHR, Ø3/8 ID Z-STL SPLIT LOCK 010091 SCR, 1/4-20x3/8 BO SKT SET 012869...

  • Page 72: Left Gearbox Assembly

    Left Gearbox Assembly - 037654 SECTION 4 Illustration PARTS Page 4-16 061090 - 12/2013...
  • Page 73 Left Gearbox Assembly - 037654 SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION OIL, MOBILE SHC 634 GEAR .75 GAL 001004 010037 FSTN, HHCS 3/8-16 X 1-1/4 GR 5 BOLT, 3/8-16x1-1/2 GR 5 HHCS 010038 WSHR, Ø3/8 ID Z-STL SPLIT LOCK 010091 SCR, 1/4-20x3/8 BO SKT SET 012869...

  • Page 74: Pitch Control Assembly

    Pitch Control Assembly SECTION 4 Illustrations PARTS Page 4-18 061090 - 12/2013...
  • Page 75 FSTN, NUT NYLOK 3/8-16 010464 032377 DECAL, F/ PITCH CONTROL TUBE 038174 RIDER MANUAL PITCH CONTROL ASSY 053442 DECAL, ALLEN VERTICAL BRUSHED CHROME ITEM PART NO. DESCRIPTION 015410 FSTN, RHMS 1/4-20 X 3/8 015747 PIN, ROLL 3/16 X 1-3/8 SPIROL...

  • Page 76: Kill Switch Pedal Assembly

    Kill Switch Pedal Assembly - 059535 SECTION 4 Illustration PARTS Page 4-20 061090 - 12/2013...
  • Page 77 Kill Switch Pedal Assembly - 059535 SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION FSTN, HHCS 1/4-20 X 3/4 010002 FSTN, FW 5/16 010082 SWITCH, KILL FOR RIDING TROWEL 033892 024840 PLATE, PEDAL FOOT SPEED 024851 THROTTLE HOUSING WMNT PIN, Ø3/32 X 3/4 ZP STL COTTER 026226 028895...

  • Page 78: Throttle Pedal Assembly

    Throttle Pedal Assembly - 059533 SECTION 4 Illustration PARTS Page 4-22 061090 - 12/2013...
  • Page 79 Throttle Pedal Assembly - 059533 SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION SCR, 5/16-18x1 HHC 010020 FSTN, NUT HEX 5/16-18 010100 PIN, Ø1/16 X 1 ZP STL COTTER 010131 PIN, Ø1/8 X 1 COTTER 012361 ASSY, FOOT SPEED PEDAL 024839 024851 THROTTLE HOUSING WMNT...

  • Page 80: Steering Assembly

    Steering Assembly SECTION 4 Illustration PARTS Page 4-24 061090 - 12/2013...
  • Page 81 Steering Assembly SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION 010005 BOLT, 1/4-20x1-1/2 GR 8 HHC 010051 FSTN, NUT HEX JAM 1/2-20 FINE FSTN, HHCS 1/2-13 X 1-1/2 010069 010093 FSTN, LW 1/2 FSTN, NUT NYLOK 3/8-16 010464 FSTN, NUT HEX NYLOK 1/2-13 011238 019900 ROD, END FEMALE 1/2”...
  • Page 82 Steering Assembly - cont’d SECTION 4 Illustration PARTS Showing the Versa steering linkage fixed rigid to frame. Showing the Versa steering linkage connected. Page 4-26 061090 - 12/2013...
  • Page 83 Steering Assembly - cont’d SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION 010005 BOLT, 1/4-20x1-1/2 GR 8 HHC 010051 FSTN, NUT HEX JAM 1/2-20 FINE FSTN, HHCS 1/2-13 X 1-1/2 010069 010093 FSTN, LW 1/2 FSTN, NUT NYLOK 3/8-16 010464 FSTN, NUT HEX NYLOK 1/2-13 011238...

  • Page 84: Spray System Assembly

    Spray System Assembly SECTION 4 Illustration PARTS Page 4-28 061090 - 12/2013...
  • Page 85 Spray System Assembly SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION 012702 TIP, 80°x0.10 GPM BRASS SPRAY 033735 PUMP, SPRAY SYSTEM FILTER, RETARDANT SPRAY SYSTEM 040209 040387 ELBOW, 3/8 BRASS 90° STREET FTG, 3/8X1/4 BRASS FM TO FM REDUCER 040388 BODY, NYLON CHECK VALVE NOZ 041604...

  • Page 86: Mainframe Assembly

    Mainframe Assembly SECTION 4 Illustration PARTS Page 4-30 061090 - 12/2013...
  • Page 87 Mainframe Assembly SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION FSTN, HHCS 5/16-18 X 3/4 GR 5 010019 010035 FSTN, HHCS 3/8-16 X 3/4 FSTN, HHCS 3/8-16 X 1 010036 010037 FSTN, HHCS 3/8-16 X 1-1/4 GR 5 010073 FSTN, HHCS 1/2-13 X 2-1/2 GR 5 010083 FSTN, FW 3/8...

  • Page 88: Fuel System Assembly

    Fuel System Assembly SECTION 4 Illustration PARTS Fuel Tank Vent Page 4-32 Fuel Supply 061090 - 12/2013...
  • Page 89 Fuel System Assembly SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION SCR, 5/16-18x1 HHC 010020 FSTN, LW 5/16 010090 FSTN, CLAMP SIZE 4 MINI 019430 037777 ASSY, FUEL FILTER PUMP, 12 V ELECTRONIC FUEL 040330 ENGINE, KUBOTA 44 TURBO V1505TEBB-1 043291A COVER, FUEL PUMP 046441...

  • Page 90: Power Drive Assembly

    Power Drive Assembly SECTION 4 Illustration PARTS Page 4-34 061090 - 12/2013...
  • Page 91 Power Drive Assembly SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION FSTN, HHCS 3/8-16 X 1 010036 010037 FSTN, HHCS 3/8-16 X 1-1/4 GR 5 010058 FSTN, HHCS 7/16-14 X 2 FSTN, HHCS 1/2-13 X 1-1/4 GR 5 010068 010083 FSTN, FW 3/8 FSTN, FW 7/16...
  • Page 92 Power Drive Assembly - cont’d SECTION 4 Illustration PARTS ENGINE AND MOTOR PLATE OMITTED FOR CLARITY Page 4-36 061090 - 12/2013...
  • Page 93 Power Drive Assembly - cont’d SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION 059763 FSTN, FW 1 1/4” GR 8 YELLOW ZINC BEARING SUPPORT WMNT, MIDDLE 060806 SPROCKET, POLYCHAIN, 8MX-67S-21 060809 SPROCKET, POLYCHAIN, 8mx-56s-21 060810 SPROCKET, POLYCHAIN, 8MX-33S-21 060811 BELT, POLYCHAIN, 8MGT-800-21 060812 BELT, POLYCHAIN,8MGT-1000-21...
  • Page 94 Power Drive Assembly - cont’d SECTION 4 Illustration PARTS Page 4-38 061090 - 12/2013...
  • Page 95 Power Drive Assembly - cont’d SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION FSTN, HHCS 3/8-16 X 1 010036 010037 FSTN, HHCS 3/8-16 X 1-1/4 GR 5 010058 FSTN, HHCS 7/16-14 X 2 FSTN, HHCS 1/2-13 X 1-1/4 GR 5 010068 010083 FSTN, FW 3/8...

  • Page 96: Engine Mounting Assembly

    Engine Mounting Assembly SECTION 4 Illustration PARTS Page 4-40 061090 - 12/2013...
  • Page 97 Engine Mounting Assembly SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION FSTN, HHCS 1/4-20 X 1/2 GR 5 010001 FSTN, HHCS 5/16-18 X 1-1/4 GR5 010021 FSTN, HHCS 3/8-16 X 1 010036 FSTN, HHCS 1/2-13 X 1-1/4 GR 5 010068 FSTN, FW 5/16 010082...
  • Page 98 Engine Mounting Assembly - cont’d SECTION 4 Illustration PARTS Page 4-42 061090 - 12/2013...
  • Page 99 Engine Mounting Assembly - cont’d SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION 048635 BRACKET, THROTTLE X1 BAR, BATTERY HOLD DOWN 048932 BRACKET, RAD SUPPORT MSP460 049028 ENGINE MOUNT 049633 049647 MUFFLER 055040 FSTN, NUT HEX 1/2-13 GR8 YELLOW ZINC BEARING SUPPORT WMNT, MIDDLE 060806 BEARING SUPPORT PLATE...

  • Page 100: Engine Assembly

    Engine Assembly - 450C SECTION 4 Illustration PARTS Page 4-44 061090 - 12/2013...
  • Page 101 Engine Assembly - 450C SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION FSTN, HHCS 1/4-20 X 1/2 GR 5 010001 FSTN, HHCS 5/16-18 X 1 010020 FSTN, HHCS 5/16-18 X 1-1/4 GR5 010021 FSTN, HHCS 3/8-16 X 1 010036 FSTN, HHCS 1/2-13 X 1-1/4 GR 5 010068 FSTN, FW 5/16...
  • Page 102 Engine Assembly - 450C (cont’d) SECTION 4 Illustration PARTS Page 4-46 061090 - 12/2013...
  • Page 103 Engine Assembly - 450C (cont’d) SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION 037798 FSTN, HHCS 1/2-13 X 1 1/2 GR8 038590 SPACER, CLUTCH FSTN, 1/2-13 STOVER NUT 040208 ENGINE, KUBOTA 44 TURBO V1505TEBB-1 043291A SCR, 10MMx1.25x30 HHC 043443 COVER, FUEL PUMP 046441 047273...

  • Page 104: Electrical Schematic

    Electrical Schematic SECTION 4 Illustration PARTS Page 4-48 061090 - 12/2013...
  • Page 105 Electrical Schematic SECTION 4 Illustration PARTS Page 4-49 061090 - 12/2013...

  • Page 106: Front Dolly Jack Assembly

    Front Dolly Jack Assembly SECTION 4 Illustration PARTS 027684 Page 4-50 061090 - 12/2013...
  • Page 107 Front Dolly Jack Assembly SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION PIN, 3/16 X 2 COTTER 010133 FSTN, NUT NYLOK 3/8-16 010464 015692 CAP, Ø1/4 RED GREASE 017751 FSTN, FW HARD A325 3/8 (p) SPACER, DOLLY JACK 024628 026729 LIFT, FRONT DOLLY JACK JACK, SP DOLLY...

  • Page 108: Rear Dolly Jack Assembly

    Rear Dolly Jack Assembly SECTION 4 Illustration PARTS 027684 Page 4-52 061090 - 12/2013...
  • Page 109 Rear Dolly Jack Assembly SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION PIN, 3/16 X 2 COTTER 010133 FSTN, NUT NYLOK 3/8-16 010464 015692 CAP, Ø1/4 RED GREASE 017751 FSTN, FW HARD A325 3/8 (p) SPACER, DOLLY JACK 024628 026728 LIFT, REAR DOLLY JACK JACK, SP DOLLY...

  • Page 110: Trowel Arm Alignment Jig Assembly

    Trowel Arm Alignment Jig Assembly SECTION 4 Illustration PARTS 016863 Page 4-54 061090 - 12/2013...
  • Page 111 Trowel Arm Alignment Jig Assembly SECTION 4 Parts List PARTS ITEM PART NO. DESCRIPTION 015884 SCREW, 3/8-16x1 SCKT CAP 016877 FSTN, SHCS 3/8-16 X 1-1/2 028076 SCREW, 3/8-16x2 SCKT CAP BASE 028981 CLAMP, BLOCK 028982 028983 SPACER, 2.600 HGT ADJUSTING 028984 028985 WASHER...

  • Page 112: Accessories

    Accessories SECTION 4 PARTS 051552 - CLIP-ON PAN 051553 - SAFETY CATCH PAN 042779 - LIFT BRIDLE, 2500# 6’ SLING Page 4-56 061090 - 12/2013...
  • Page 113 INTENTIONALLY BLANK 061090 - 12/2013...
  • Page 114 YOUR TOTAL SOURCE FOR CONCRETE EQUIPMENT 800-643-0095 or 870-236-7751 FAX: 800-643-0097 or 870-236-3934 P.O. Box 819 Paragould, Arkansas 72451 USA www.alleneng.com 061090 - 12/2013...

This manual is also suitable for:

Msp450c060800065150

Table of Contents