Download
Share
Print this page
BT TM-7 Owner's Manual
  1. Manuals
  2. Brands
  3. BT Manuals
  4. Paintball equipment
  5. TM-7
  6. Owner's manual

BT TM-7 Owner's Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
O W N E R ' S
M A N U A L
B T P A I N T B A L L . C O M

Advertisement

loading

Related Manuals for BT TM-7

Summary of Contents for BT TM-7

  • Page 1 O W N E R ’ S M A N U A L B T P A I N T B A L L . C O M...

  • Page 2: Table Of Contents

    14. Assembly/Disassembly Instructions 15. Storage and Transportation 16. Troubleshooting Guide 17. Diagram and Parts List ©2008 BT Paintball Designs, Inc. The BT Shield, “Battle Tested” and “TM-7” are trademarks of 18. Warranty Information BT Paintball Designs, Inc. All rights reserved.
  • Page 3 “low pressure” (350-450 psi) fixed-output sys- The use of long life batteries is recommended. The battery is installed by tem is utilized as an air source for your TM-7. Using a “high pressure” out- sliding the battery door open and replacing the 9 volt battery.
  • Page 4 Safety Position. To make the TM-7 Live, move the • Do not install compressed air or load paintballs into your TM-7 until you Selector Switch to the desired feel completely confident with your ability to handle your TM-7 safely.
  • Page 5 Fit TM-7 marker is OFF. Push the Power button and hold for 2 seconds until the loader directly into the feed elbow. It might be necessary to adjust the the LED light changes from Green to Red feed elbow pinch bolt to your loader.
  • Page 6 • Move the Selector switch to the safety position (0). The TM-7 regulator should be factory pre-set at 200 PSI as this is the best operating pressure for firing the marker. However, if over time you do •...

  • Page 7: Programming

    • This marker is not designed to shoot above the safety limits established by industry standards but under certain conditions it may. It is therefore important to check the velocity each time before playing with your TM-7. Adjusting Velocity At the back of the TM-7 main body is the Bolt Guide Cap.

  • Page 8: Setting Functions

    Decrease a Function’s Value Returns a Function to Factory Default To Enter Programming Mode- The TM-7 must be OFF and the tourna- the Selector switch to Position (0) then simply pull the trigger once and the LED ment lock must be OFF to begin managing the functions. While the TM- will flash the new value.
  • Page 9 The default Max ROF is 4 flashes (12 BPS). first 3 safety shots; then if player maintains at least one pull per second, the TM-7 will fire ‘X’ number of shots per pull and release of the trigger as Flashes/ROF...

  • Page 10: Trigger Adjustments

    To reset all the Functions to the defaults, turn OFF your TM-7, then press Notes: and hold the Tournament Lock button in for 5 seconds. The LED will blink • If any of the set screws are over adjusted in any direction the TM-7 may AMBER to confirm the reset. not fire.

  • Page 11: General Maintenance

    Use warm water and a barrel cleaning device to keep the Barrel in top condition. • Do Not work on your TM-7 until the Air source is removed and it is verified that the regulator gauge reads 0 psi and no air is trapped in the TM-7.
  • Page 12 The stock assembly and stock lock assembly can be easily removed once • Using a 7/64" Allen key loosen the 7 socket head screws, located on the outer shell is separated. If you decide not to use the stock, the TM-7 also the left side shell.
  • Page 13 Poppet front sealing face. Removal of Bolt Guide Assembly • Inspect and lubricate Poppet O-ring and be careful not to lubricate the Caution: Make sure the TM-7 is completely empty of air before removing front Poppet Seal. the Bolt Guide Assembly.

  • Page 14: Storage And Transportation

    For your own • Using a 5/64" Allen key, remove the two Circuit Board screws and safety and to protect the image of the sport, always carry your TM-7 in a gently remove the Circuit Board.

  • Page 15: Troubleshooting Guide

    If it is, unplug the battery from the harness for 5 minutes, then plug back in and try again. • It may be a good idea to remove the battery when storing your TM-7 to prevent unauthorized use.This is not a toy. Misuse may cause seri-...
  • Page 16 Leaks Solenoid may To reset the solenoid, with the eyes OFF, pull the trigger Regulator Regulator If the needle on the regulator’s gauge climbs well over 200 constantly need to be repeatedly until the solenoid makes a clicking sound again pressure adjusted too psi when attempting to install the air tank, first remove the...
  • Page 17 Breaks Ball detents Clean the ball detents. If necessary, apply a small amount Inconsistent Battery may Replace battery with a fresh Duracell or Energizer brand paint in may be dirty of grease around the outer surface to reduce friction inside velocity be low.
  • Page 18 Schematic # Description SKU# Schematic # Description SKU# SELECTOR SCREW (flat head 4-40 x .5) 17650 REGULATOR OPP ASSEMBLY (complete) 17597 FRAME SCREW (flat head 6-32 x .313) 17651 BALL DETENT ASSEMBLY (complete) 17541 CIRCUIT BOARD SCREW (button head 6-32 x . 1 57) 17652 MAIN BODY 17677 GRIP SCREW-TOP (button head 6-32 x .250)
  • Page 19 B T P A I N T B A L L . C O M...
  • Page 20 B T P A I N T B A L L . C O M...

  • Page 21: Warranty Information

    BT Paintball. All other services will be duly charged by over the phone credit card and shipped UPS.
  • Page 22 For your own safe- ty and to protect the image of the sport, always carry your TM-7 in a suit- We expect you to play hard and play frequently and thus the TM-7 was able marker case or in the box in which it was shipped.
  • Page 23 B T P A I N T B A L L . C O M...