Related Manuals for BT SA-17
Summary of Contents for BT SA-17
- Page 1 BT_SA-17_Manual.qxp 3/11/10 9:54 AM Page C O W N E R ’ S M A N U A L B T P A I N T B A L L . C O M...
-
Page 2: Table Of Contents
“Battle Tested” are trademarks of BT Paintball Designs. All rights reserved. NEITHER BT PAINTBALL DESIGNS, INC. NOR ANY OF ITS PRODUCTS ARE AFFILIATED WITH TIPPMANN SPORTS, LLC. Patents pending. B T P A I N T B A L L . C O M... -
Page 3: Rules For Safe Marker Handling
Model ........ -
Page 4: Getting Started
BT_SA-17_Manual.qxp 3/11/10 9:54 AM Page 2 3. Getting Started In this manual, you will see the term “Safe Mode”. In “Safe Mode”, the Safety should be set to “Safe” (red marking on safety will not be visible) and Safety and safe Marker handling are the most important aspects of a barrel-blocking device should be used. - Page 5 • Position the BT Marker so that the Fig. 3.7 BT Marker, or a recognized and competent air smith, for instruction in the door is pointed upwards while safe handling of CO cylinders before purchasing or installing one into keeping the muzzle of the Marker your BT Marker.
-
Page 6: Firing Your Marker
• Turn the feed adapter plug to the “B” position to feed paintballs into the make sure that anyone within range of the BT Marker does the same. Marker or to position “C” to lock them within the feed tube. -
Page 7: Unloading Your Marker
• Visually inspect each making sure they are clean and dry. (set to “Fire”). Lubricating the Bolt/Hammer Assembly • Keeping the BT Marker pointed in a safe direction, pull the trigger until the remaining CO is expelled and it fails to re-cock. -
Page 8: Disassembly/Reassembly
• Then using your forefinger, pull the breech insert out of the front of the marker. •Install the components into the puncture pin housing; refer to the dia- • You can also use a paintball swab, like the BT Battle Swab, to remove gram for proper alignment. -
Page 9: Storage And Transportation
ALWAYS KEEP I I M M P P O O R R T T A A N N T T : : Never carry your BT Marker uncased when not on a play-... -
Page 10: Parts List And Diagram
Ball Detent (Complete) 17541 Breech Insert (.688) 17969 O-Ring (015-ur) 57738 Main Body 17970 Front Bolt 73124 SA-17 Name Plate 17971 Cocking Block Assembly 73127 Locking Quick Release Pin 17972 Cocking Rod 73126 12 Gram Retainer 17973 Retaining Ring (large) - Page 11 BT_SA-17_Manual.qxp 3/11/10 9:54 AM Page 9 B T P A I N T B A L L . C O M...
-
Page 12: Troubleshooting
N N O O T T E E : : If you are experiencing any problems and you are using any after- are not designed by BT Paintball to work in the SA-17, and they may be the market parts, it is necessary to re-install the factory parts and re-test cause of the problems. -
Page 13: Limited Lifetime Warranty
BT will repair or replace with the same or equivalent This Limited Warranty gives you specific legal rights, and you may also have other rights which vary model, without charge, any of its products that have failed in normal use because of a defect from state to state. - Page 14 BT_SA-17_Manual.qxp 3/11/10 9:54 AM Page 12 B T P A I N T B A L L . C O M...
- Page 15 BT_SA-17_Manual.qxp 3/11/10 9:54 AM Page E B T P A I N T B A L L . C O M B T P A I N T B A L L . C O M...
- Page 16 BT_SA-17_Manual.qxp 3/11/10 9:54 AM Page B B T P A I N T B A L L . C O M...