Specifications - Makita HR4001C Instruction Manual

ENGLISH (Original instructions)

SPECIFICATIONS

Capacities
No load speed (min
Blows per minute
Overall length
• Due to our continuing programme of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for hammer drilling in brick, con-
crete and stone as well as for chiselling work.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted noise level determined accord-
ing to EN60745:
Model HR4001C
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Model HR4010C,HR4011C
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN60745:
Model HR4001C
Work mode : chiselling
Vibration emission (a
Uncertainty (K) : 2.0 m/s
Work mode : chiselling function with side grip
Vibration emission (a
Uncertainty (K) : 2.5 m/s
Work mode : hammer drilling into concrete
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model HR4010C
Work mode : chiselling
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model
Carbide-tipped bit
Core bit
-1
)
Net weight
Safety class
) : 92 dB (A)
pA
) : 103 dB (A)
WA
) : 90 dB (A)
pA
) : 101 dB (A)
WA
2
) : 10.5 m/s
h,CHeq
2
2
) : 10.0 m/s
h,CHeq
2
2
) : 12.5 m/s
h,HD
2
2
) : 7.0 m/s
h,CHeq
2
HR4001C
6.3 kg
Work mode : chiselling function with side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : hammer drilling into concrete
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model HR4011C
Work mode : chiselling
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : chiselling function with side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : hammer drilling into concrete
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration emission value has
been measured in accordance with the standard test
method and may be used for comparing one tool with
another.
NOTE: The declared vibration emission value
may also be used in a preliminary assessment of
exposure.
WARNING:
The vibration emission during actual
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
5 ENGLISH
HR4010C HR4011C
40 mm
105 mm
235 - 480
1,350 - 2,750
468 mm
6.7 kg 6.7 kg
/II
2
) : 8.0 m/s
h,CHeq
2
2
) : 9.0 m/s
h,HD
2
2
) : 6.5 m/s
h,CHeq
2
2
) : 6.5 m/s
h,CHeq
2
2
) : 7.5 m/s
h,HD
2