Specifications - Makita HR2470 Instruction Manual

ENGLISH (Original instructions)

SPECIFICATIONS

Capacities
No load speed (min
Blows per minute
Overall length
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s). The lightest and heaviest combinations, according to
EPTA-Procedure 01/2014, are shown in the table.
Intended use
The tool is intended for hammer drilling and drilling in
brick, concrete and stone as well as for chiselling work.
It is also suitable for drilling without impact in wood,
metal, ceramic and plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-6:
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
NOTE: The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Model
Concrete Tungsten-carbide
tipped bit
Core bit
Diamond core bit
(dry type)
Steel
Wood
-1
)
Net weight
Safety class
) : 89 dB (A)
pA
) : 100 dB (A)
WA
HR2470/HR2470F
370 mm
2.9 - 3.3 kg
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-6:
Model HR2470, HR2470F
Work mode : chiselling
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : hammer drilling into concrete
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model HR2470T, HR2470FT
Work mode : chiselling
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : hammer drilling into concrete
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
5 ENGLISH
HR2470T/HR2470FT
24 mm
54 mm
65 mm
13 mm
32 mm
0 - 1,100
0 - 4,500
394 mm
3.0 - 3.3 kg
/II
2
) : 14.3 m/s
h,CHeq
2
2
) : 15.9 m/s
h,HD
2
2
) : 16.3 m/s
h,CHeq
2
2
) : 15.7 m/s
h,HD
2