Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Rice Lake Retail Series
Summary of Contents for Rice Lake Retail Series
- Page 1 Retail Series Calibration Manual January 5, 2018 PN 170120 Rev A...
- Page 2 All information contained within this publication is, to the best of our knowledge, complete and accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make changes to the technology, features, specifications and design of the equipment without notice.
-
Page 3: Table Of Contents
WM-Ai ..................22 Technical training seminars are available through Rice Lake Weighing Systems. -
Page 4: Counter-Top Scales
Retail Series Calibration Manual Counter-Top Scales RS-130/RS-160 Follow the steps below to complete the calibration process. 1. Turn on the scale while pressing until 6.3 displays. CHANGE 2. Press and hold until SETUP displays. ZERO 3. Press to enter calibration mode. The WEIGHT display flashes CAL-1 and shows UNIT 1. -
Page 5: Simulate No Power Display
WEIGHT display shows SETUP (approximately three seconds). ZERO 3. Press , weight display shows USUAL. 4. Press , WEIGHT display shows -0.00-, UNIT PRICE $ display shows -0.00-, TOTAL $ display shows Lo-. © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 6: Astra
Retail Series Calibration Manual Astra ow to calibrate the Ast Follow the steps bel ra scale. 1. Turn the scale off. 2. Turn the scale on while pressing . Release after the second beep. C00 TEST displays. 3. Press followed by . -
Page 7: Bc-4000 L2/E
Hardware Test menu (C01). C01 HARDWARE TEST displays. 12. Turn off the power to exit the Test Mode. Do not use the RESET key to exit from Test Mode. IMPORTANT © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 8: Uni-3
Retail Series Calibration Manual SR-2000 Follow the steps below to calibrate the SR-2000 scale. 1. Press 2. Enter 495344 and press 3. Select from the list. 4. With no weights on the platter, press to initialize the calibration values. The initial A/D value should be 20000 ± 1. -
Page 9: Uni-5 And Uni-7
6. With no weight on the platter, press to initialize the A/D values. The initial value should be 20000 ± 1. 7. Place scale capacity weight on the platter and press © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 10: Uni-9
Retail Series Calibration Manual The A/D value should be 80000 ± 2. 8. Remove the weight. 9. Save the calibration data by pressing the located underneath the platter. Memory Switch Figure 1-9. Uni-5 and Uni-7 Memory Switch location 10. Press and press 11. - Page 11 Memory Switch Figure 1-11. Uni-9 Memory Switch location 10. Press in the upper right corner. Figure 1-12. Executing Scale Adjustment 11. Verify the weight readings in operation mode. © Rice Lake Weighing Systems ● All Rights Reserved...
-
Page 12: Hanging Scales
Retail Series Calibration Manual Hanging Scales BC-4000L2H Follow the steps below to calibrate the BC-4000L2H scale. 1. Turn the scale off. 2. Turn the scale on while holding down the key until it beeps twice. C00 TEST MODE displays. 3. Enter a using the keypad and press the . -
Page 13: Uni-7 Hanging
14. Verify the weight readings in operation mode. Uni-7 Hanging Follow the steps below to calibrate the Uni-7 hanging scale. 1. Press 2. Enter and press to access hidden menus. 495344 3. Press Figure 2-3. © Rice Lake Weighing Systems ● All Rights Reserved... - Page 14 Retail Series Calibration Manual 4. Select from the list. CALIBRATION 5. To select Single Range or Multi Range, enter and press as needed. 495344 SINGLE MULTI 6. With no weight on the platter, press to initialize the A/D values. The initial value should be 20000 ± 1.
-
Page 15: Uni-9 Hanging
9. Remove outside screw to access the located on top of the scale body near the mounting pole bracket. Memory Switch 10. Save the calibration data by pressing the Memory Switch Figure 2-6. Uni-9 Memory Switch location © Rice Lake Weighing Systems ● All Rights Reserved... - Page 16 Retail Series Calibration Manual 11. Press the in the upper right corner. Figure 2-7. 12. Verify the weight readings in operation mode. Visit our website www.RiceLake.com...
-
Page 17: Wrapping Systems
Hardware Test menu (C01). C01 HARD TEST displays . 12. Turn off the power to exit the Test Mode. IMPORTANT Do not use the RESET key to exit from Test Mode. © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 18: Ip-Emz/Omni-4000
Retail Series Calibration Manual IP-EMZ/OMNI-4000 Follow the steps below to calibrate the IP-EMZ scale and the OMNI-4000 auto wrapper. 1. Press Figure 3-2. 2. Enter 495344 and press 3. Select from the list. 4. With no weight on the platter, press to initialize the A/D values. -
Page 19: Ip-Ai
9. Save the calibration data by pressing the located underneath the platter, remove the small plastic Memory Switch rectangular cover and the seal bolt and metal cover. Figure 3-5. Memory Switch Location © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 20: Uni-7 Rp
Retail Series Calibration Manual 10. Press the in the upper right corner. Figure 3-6. 11. Verify the weight readings in operation mode. Uni-7 RP Follow the steps below to calibrate the Uni-7 RP scale. 1. Press 2. Enter and press to access hidden menus. -
Page 21: Uni-9 Rp
A/D values. The initial value should be 20000 ± 1. 7. Place scale capacity weight on the platter and press The A/D value should be 80000 ± 2. 8. Remove the weight. © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 22: Wm-Nano
Retail Series Calibration Manual 9. Save the calibration data by pressing the located behind a white plastic plug on the side of the remote Memory Switch scale base. Figure 3-10. Uni-9 RP Memory Switch location 10. Press the in the upper right corner. - Page 23 RETURN ARROW 11. Verify the weight in readings in operation mode. WM-4000 Follow the steps below to calibrate the WM-4000 auto wrapper. 1. Press the key. MENU Figure 3-14. © Rice Lake Weighing Systems ● All Rights Reserved...
- Page 24 Retail Series Calibration Manual 2. Enter and press the key. 495334 TEST MODE Figure 3-15. 3. Select from the list. CALIBRATION Figure 3-16. 4. With no weight on the platter, press the key to initialize the A/D values. ZERO Figure 3-17.
-
Page 25: Wm-Ai
Follow these steps to calibrate the WM-Ai auto wrapper. 1. Press the key. 2. Enter and press the key to access hidden menu steps. 495344 3. Press Figure 3-20. WM-Ai Menu 4. Select from the list. CALIBRATION © Rice Lake Weighing Systems ● All Rights Reserved... - Page 26 Retail Series Calibration Manual 5. Press , to select the range needed. SINGLE MULTI 6. With no weight on the platter, press to initialize the A/D values. The initial value should be 20000 ± 1. 7. Place scale capacity weight on the platter and press The A/D value should be 80000 ±...
- Page 28 Specifications subject to change without notice. Rice Lake Weighing Systems is an ISO 9001 registered company. 230 W. Coleman St. • Rice Lake, WI 54868 • USA U.S. 800-472-6703 • Canada/Mexico 800-321-6703 • International 715-234-9171 • Europe +31 (0)26 472 1319...