1. Package Contents Thank you for purchasing PLANET Industrial Wall-mount Managed Gigabit Switch, WGS-5225-8UP2SV. The table below shows the model with the number of ports: Model Name Copper Port Fiber Port 2.4 LCD WGS-5225-8UP2SV 8 x 10/100/1000T 2 x 100/1000/2500X ...
2. Requirements z A flat-blade screwdriver z Workstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/IP protocols. z Workstations are installed with Ethernet NIC (Network Interface Card) z Ethernet Port Connection Network cables -- Use network (UTP) cables with RJ45 connectors. ...
3. Hardware Installation 3.1 Wall Mount Installation To install the Wall-mount Managed Switch on the wall, simply follow the following steps: Step 1: Drill 4 holes with 8mm diameter on the wall. The horizontal and vertical distances between the 2 holes are 230mm and 124mm, respectively. Ø4mm Ø8mm 124mm...
3.2 Wall Hanging Installation To hang the Wall-mount Managed Switch on the wall, simply follow the following steps: Step 1: Drill 2 holes (one hole on each side) with 8mm diameter on the wall; the distance between the 2 holes is 230 mm and the line through them must be horizontal.
Power Input Range PWR1 PWR2 Model WGS-5225-8UP2SV DC 48-54V, 8A max DC 48-54V, 8A max Note: Maximum power requirements also rely on the real site application. 4-pin Spring Terminal Block Dual power input is required for maximum PoE loading.
4.1 Terminal Block Connector Pinout The Front Panel of the Wall-mount Managed Switch consists of one spring terminal block connector within 4 contacts. Please follow the steps below to insert the power wire. PWR 1 PWR 2 Insert positive/negative DC power wires into Contacts V1+ and V1- for Power 1, or Contacts V2+ and V2- for Power 2.
Dua l pow er inpu t for max is requ ired imu m PoE load ing. PW R 1 V 1 + PW R 2 DC Inpu t Ran ge 48-5 4V Max . Fau lt Alar m , 8A max Loa ding : 24V , 1A Sm art LC...
5. Web Login 5.1 Starting Web Management The following shows how to start up the Web Management of the Wall-mount Managed Switch. Note the Wall-mount Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address.
Page 11
3. After entering the password, the main screen appears as Figure 5-3 shows. Figure 5-3: Web Main Screen of Wall-mount Managed Switch The Switch Menu on the top of the Web page lets you access all the commands and statistics the Wall-mount Managed Switch provides. The Switch Menu always contains one or more buttons, such as “System”, “Switching”, “Routing”, “QoS”, “Security”, “Ring”...
5.2 Saving Configuration via the Web To save all applied changes and set the current configuration as a startup configuration, the startup-configuration file will be loaded automatically across a system reboot. 1. Click the Save icon on the top Switch Menu bar. 2. Press the “Save Configuration” button. 3.
6. SSH Login The Wall-mount Managed Switch also supports SSHv2 for remote management. The switch asks for user name and password for remote login when using SSHv2 client software; please use “admin” for both username and password. Default IP address: 192.168.0.100 Username: admin Password: admin Figure 6-1: Wall-mount Managed Switch SSHv2 Login Screen...
3. At the “#” prompt, enter the following command and press <Enter> as shown in following WGS-5225-8UP2SV# configure terminal WGS-5225-8UP2SV (config)# interface vlan 1 WGS-5225-8UP2SV (config-if-vlan)# ip address 192.168.1.100 255.255.255.0 The previous command would apply the following settings for the Wall-mount Managed Switch. IP Address: 192.168.1.100 Subnet Mask: 255.255.255.0...
6.2 Storing the Current Switch Configuration At the “#” prompt, enter the following command and press <Enter>. # copy running-config startup-config Figure 6-3: Saving Current Configuration Command Screen If the IP is successfully configured, the Wall-mount Managed Switch will apply the new IP address setting immediately. You can access the Web interface of the Wall- mount Managed Switch through the new IP address.
5 seconds. After the device is rebooted, you can log in the Web interface management within the same subnet of 192.168.0.xx. Reset Button 100 / 1G / 2.5G SFP Reset Figure 7-1: WGS-5225-8UP2SV Reset Button-...
8. LCD Touch Screen The WGS-5225-8UP2SV has a 2.4-inch color LCD touch screen with management functions. Tap the LCD touch screen to wake the LCD touch screen. Figure 8-1: To wake the LCD touch screen The factory default LCD configurations are shown as follows. Default LCD: Enable Default Touch Screen: Enable...
Page 18
You can use the Web management interface and click LCD, and then in the LCD Management, change LCD configuration. Please refer to the user’s manual for more.
9. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team. PLANET online FAQs: https://www.planet.com.tw/en/support/faq Support team mail address: support@planet.com.tw WGS-5225-8UP2SV User’s Manual: https://www.planet.com.tw/en/support/downloads?&method=keyword&keyword=w...