Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Planet WGSW-2403
Summary of Contents for Planet WGSW-2403
- Page 1 24-port + 3-slot Stackable Ethernet Switch WGSW-2403 User’s Manual...
- Page 2 Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
-
Page 3: Table Of Contents
TABLE OF CONTENTS CHAPTER 1 INTRODUCTION ... 1 1.1 C ... 1 HECKLIST 1.2 A ... 1 BOUT THE WITCH 1.3 F ... 1 EATURES 1.4 S ... 2 PECIFICATIONS CHAPTER 2 HARDWARE INSTALLATION... 4 2.1 F ... 4 RONT ANEL 2.2 R ... -
Page 4: Chapter 1 Introduction
The IEEE 802.1Q with VLAN tagging feature make logically separating nodes easier and up to 255 VLAN group are allowed on the WGSW-2403. Rate control is also supported to allow bandwidth allocation on a per-port basis. Two priority queues ensure critical applications get the bandwidth and priority they need. -
Page 5: Specifications
Power Consumption EMC/EMI Management Interface Protocols and Standards 24-port + 3-slot Stackable Ethernet Switch WGSW-2403 24 x RJ-45 2 x RJ-45 2 for 10/100/1000Base-T, 1000Base-SX and 1000Base-LX modules 1 for 100Base-FX modules, shared with port 1 1 x RS-232 DB-9... - Page 6 IEEE 802.1p QoS RFC 768 UDP RFC 783 TFTP RFC 791 IP RFC 792 ICMP RFC 826 ARP RFC 854 Telnet RFC 2068 HTTP RFC 2236 IGMPv2 Network Management RFC 1157 SNMP v1/v2 RFC 1123 MIB-2 RFC 1493 Bridge MIB Enterprise private MIB - 3 -...
-
Page 7: Chapter 2 Hardware Installation
Chapter 2 HARDWARE INSTALLATION STACK Switch ID RESET WGSW-2403 Switch front panel On: Power on When this LED steady green, it means the device acts competent leading role (Master), an indispensable essential for system administrator to control and monitor whole system. - Page 8 FDX/COL Steady Amber Flashing Amber Module LNK/ACT Green Flashing Green STACK Green Stack ports There are two stack ports on the front panel. One is IN and the other is OUT. When stacked, the IN port should connect to the other switch’s OUT port and the OUT port should connect to other switch’s IN out.
- Page 9 100Base-FX SC multi-mode fiber module 100Base-FX SC multi-mode fiber module The auto-negotiation feature of the switch allows each port of the device running at one of the following operation modes: Port Media 10/100Mbps 100Mbps fiber optic (Alternative to copper port-1) 10/100Mbps RJ-45 (copper) All copper ports supports MDI/MDI-X automatically crossover capability that is the port can connect either the PC or hub without crossover cable adjustment.
-
Page 10: Rear Panel
10Mbps 100Mbps 1000Mbps 1000BASE-SX 1000Mbps 1000BASE-LX 1000Mbps NOTE: MMF-multimode fiber, SMF – Single mode fiber CONSOLE 9600, 8, N, 1 WGSW-2403 Switch rear panel WGSW-D1SX 1000Base-SX 1000BASE-SX : WGSW-D1SX WGSW-D1LX 1000Base-LX 1000BASE-LX : WGSW-D1LX WGSW-D1GT 1000Base-T 1000BASE-T : WGSW-D1GT Duplex Mode Wiring... -
Page 11: Hardware Installation
Console Port The RS-232 console is an interface for connecting a terminal directly. Through the console port, it provides rich diagnostic information includes network statistics, link status and system setting. The operating mode of the console port is: 9600 (Fix baud rate) n (No parity checking) 8 (8 Data bits) 1 (1 stop bit) - Page 12 Cabling is away from: w Sources of electrical noise such as radios, transmitters and broadband amplifiers w Power lines and fluorescent lighting fixtures. Keep water or moisture off. Airflow around the unit and through the vents in the side of the case is great for heat radiation (company recommend that you provide a minimum of 25 mm clearance).
-
Page 13: Stack Installation
Push the module gently into the slot along the slide tracks. Ensuring that it firmly engages with the connector then tighten the screws to secure the module. CAUTION: The slide-in slots are not hot swappable, power off the switch before installing modules. -
Page 14: Chapter 3 Console And Telnet Management
Chapter 3 CONSOLE AND TELNET MANAGEMENT 3.1 Connect To PC by RS-232 serial Cable NOTE: If you have stacked several switches together, make sure you are working on Master switch (switch with least Switch ID). Other slave switches’ management interface allows only viewing the configuration by “guest” account. To configure the system, connect the provided serial cable to a COM port on a PC or notebook computer and to serial (console) port of the device. -
Page 15: Main Menu
“guest”: guest can view the whole switch information only, moreover, access to Web management interface is not allowed. The default password is “guest”. Main menu appears after successfully login WGSW-2403. To enter any of the submenus, simply type the number after the command prompt. When select further options, you may be asked for the device ID which you want to configure. - Page 16 Main menu Submenu 1. Topology Information 1. System Information 2. System Information 3. System Configuration 1. Network Configuration 2. Console Port Status Display 3. SNMP Community Setup 2. Management Setup 4. Trap Receiver Control 5. Management Features Control 6. Trap Filtering Setup 1.
- Page 17 6. Mirror 7. Statistic Information 8. Priority Tag 9. STA 10. Port Aggregation 4. User Authentication 1. System Restart 2. Default Factory Reset 3. Timeout Interval Setup 5. System Utility 4. TFTP Download 5. Local Transfer 6. Ping 7. Search Location by Port Name 6.
-
Page 18: Chapter 4 Web Management
4.1 Start A Web Browser Session The Web Interface of WGSW-2403 is coded by Java Applet and running on the Java Virtual Machine (JVM) version 1.3.1 platform. You should configure the management station with an IP address and subnet mask compatible with WGSW-2403 for accessing it. -
Page 19: Stack Main Page
4.2 Stack Main Page The stack main page contains two options: Topology This screen displays one or more switches of the management stack. Basic properties can be read by the screen, including Hardware characteristic, Device Name, Up time, Master and Slave relationship. Also, by mouse clicking listed items can enter for further operation. -
Page 20: Switch Main Page
4.3 Switch Main Page Switch Main Page appears after you click one of the switch(es) on the topology page. There are 8 function button listed on top: Home, Save, Default, Reboot, Ping, Telnet, Contact, and Upgrade. <Home> Shortcut to back to stack home page <Save>... - Page 21 <Reboot> You can specify switch(es) and reboot it. Warm Boot Reboot the switch in a short time. Cold Boot Boot the switch and with fully Power On Self Test (POST). The system is completely checked but spends much time. <Ping> The Ping is a commonly used tool to detect the remote host or IP address exists or not.
- Page 22 WEB Upload Select Device ID and “WEB Upload” radio button then click OK. Specify the file path by clicking Browse button and click Start. TFTP Download Select Device ID and “TFTP Download” radio button then click Enter the TFTP server’s IP address in Server IP field. Enter file name in File Name field.
-
Page 23: Device Configuration
Device The shortcut to go to another member switch in the management stack. 4.4 Device Configuration Panel Display MASTER LED SWITCH ID STATUS LED Port Status Port Link Down (Black): Port Link Up (Green): Port Link Up (Amber): Port Disabled (Red): 10/100Mbps Ethernet ports Port is not connected or attached device shuts down. -
Page 24: Topology Info
Network Configuration IP Address: Subnet Mask: Gateway IP: Device Information Name: Contact: Location: NOTE: The Network Configuration and Device Information of Master Device in the management stack will become system parameters automatically. 4.5 Topology Info This page displays information about the switch(es), such as Device ID, Hardware version, Boot-Up version, POST version, Runtime version (Firmware version), JAVA Applet version (Web User Interface version), Device Name and Device Location. - Page 25 NOTE: Also by simply clicking the port on the ‘Panel Display’, the port information screen pops up Configuration Port attributes can be setup in this page. Setup Port Attributes Click the “Name” column of the port. Enter a name for identification, like ‘Richard’; and press Enter Leave the “Admin”...
- Page 26 Also accomplished by simply mouse right-click the port on the ‘Panel Display’ NOTE: then select ‘Configuration’, the configuration screen pops up. Duplicate Port Attributes Click “Duplicate” button, the dialogue screen appears. Select Source Port (for example Port 1). Select Target Port, click Select the port attributes you want to duplicate.
- Page 27 Also accomplished by simply mouse right-click the port on the ‘Panel Display’ NOTE: then select ‘Copy Setting’ to duplicate port properties and select ’Past Setting’ when point at destination port. Statistic The statistics function provides the following 3 pages for various traffic information of each port.
-
Page 28: Security
A denominate port can be searched by its given name (Match whole word only). 4.7 Security This is reserved for future use. 4.8 SNMP Simple Network Management Protocol (SNMP) is a communication protocol for managing devices on a network. It is commonly used for network administrators to communicate with multiple devices (hub, switch, router ……) for configuring and monitoring while convenient for troubleshooting but no miscellaneous platform consideration. - Page 29 Select one community you want to modify in the “Current” column The “New” column lists the corresponding values; please modify it Click Modify button to update the entry Trap Manager Trap Manager specifies the Network Management Stations (NMS) that will receive trap messages from the SNMP agent and can up to 5 entries.
-
Page 30: Vlan
Trap Filtering Check the “Enable” boxes by mouse clicking to receive a notice when corresponding event occurs. 4.9 VLAN The VLAN is a group of ports that may spread around the network but communicate as though they belong to one subnet. By using VLAN, all ports can be reorganized into separate broadcast domains for security reasons and reduce bandwidth occupation instead of using routers to divide whole network into subnets. - Page 31 To remove a VLAN group Select a VLAN group you want to remove from the “Current” list. Click Remove>> button to remove it. Attention: If a removed port is no longer belonged to any other group, it is temporarily disabled because no one can communicate with it. If one port’s PVID is equal to this VLAN ID, removing this VLAN group will not allow until you change it.
- Page 32 VLAN Port Configuration When the VLAN-enabled switch receives an untagged packet, the packet will be sent to the port’s default VLAN according to the PVID (port VLAN ID) of the receiving port. To change the PVID Double click the “PVID” column of a port. Input a new VLAN ID (1~255).
-
Page 33: Igmp Snooping
Click All Together button then all the ports of the switch will be added to VLAN group 1. - All Independent Click All Independent button then all the ports will be divided into separated subnets (totally 18 subnets). Every port can belong to different Port Group VLANs simultaneously without limitation. 4.10 IGMP Snooping Multicasting is widely used to support multi-media applications such as video conferencing. -
Page 34: Sta
However, before making connections between switches, pay attention to: The ports at both ends of a Port Aggregation connection must be configured as Aggregation Ports. The ports at both ends of a Port Aggregation connection must have the same port properties, including Speed, Duplex mode. - Page 35 Information This screen displays summaries of STA information. For further configuration, please go to next section. Parameter STA State Designated Root Bridged ID Root Port Max Age (6~40 sec) Hello Time (1~10 sec) Hold Time Description Shows if STA is enabled on the switch and participated an STA compliant network.
- Page 36 Forward Delay (4~30 sec) Root Path Cost Configuration Changes Last Topology Change Configuration Parameter Usage Priority (1~65535) Hello Time (1~10sec) Maximum Age (6~40sec) Forward Delay (4~30sec) This time value, measured in units of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state.
-
Page 37: Priority
STA Port Configuration Parameters Port Priority Path Cost Fast Forward 4.13 Priority This switch supports IEEE802.1p CoS with 2-level priority. There are 8 traffic classes and 8 Service Rules in the Priority Map. When one packet carries with priority-tag, which has specified a CoS (Class of Service) comes into the switch, the specified CoS tag will determine what priority (Low/High) will it get according to the Priority Map in the switch. -
Page 38: Address Table
FIFO The first in packet, the first out packet (No priority) 1：1 Send 1 high priority packet, then 1 low priority packet 2：1 Send 2 high priority packets, then 1 low priority packet 3：1 Send 3 high priority packets, then 1 low priority packet 4：1 Send 4 high priority packets, then 1 low priority packet 5：1... -
Page 39: Mirror
Dynamic Address Counts Number of MAC addresses automatically learned by the current switch. Static Address Counts Number of MAC addresses manually added to the current switch. To add a static address Click the combo box and select a port, then the MAC address table of the port appears. - Page 40 - 37 -...
-
Page 41: Chapter 5 Troubeshooting
1. Check the VLAN and PVID settings. 2. The address table may contain older information than of the address table of that node. Please power down to refresh the address information. CHAPTER 5 TROUBESHOOTING If WGSW-2403 is not - 38 -... -
Page 42: Switch ' Srj-45 Pin Assignments
A.1 Switch‘s RJ-45 Pin Assignments 1000Mbps, 1000Base T Contact BI_DA+ BI_DA- BI_DB+ BI_DC+ BI_DC- BI_DB- BI_DD+ BI_DD- Implicit implementation of the crossover function within a twisted-pair cable, or at a wiring panel, while not expressly forbidden, is beyond the scope of this standard. A.2 10/100Mbps, 10/100Base-TX Contact MDI-X... -
Page 43: Cable Pin Assignment
A.3 RJ-45 cable pin assignment EM-WGSW2403 - 40 -...