Advertisement
Table of Contents
- 1 Important Safety Instructions
- 2 Li-Ion Battery
- 3 Charging the Battery
- 4 Cleaning Modes
- 5 Using the Multiflex® Wand
- 6 Multiflex Storage
- 7 Maintaining Your Vacuum
- 8 Emptying the Dust Cup
- 9 Cleaning the Filters
- 10 Maintenance
- 11 Floor Nozzle
- 12 Checking for Blockages
- 13 Troubleshooting Guide
- 14 Technical Specifications
- Download this manual
Advertisement
Table of Contents
Related Manuals for Shark Vertex IZ440 Series
Summary of Contents for Shark Vertex IZ440 Series
- Page 1 MultiFLEX DuoClean ® ® PowerFins Cordless Vacuum with Self-Cleaning Brushrol IZ440 Series IZ460 Series OWNER’S GUIDE POWERFINS...
-
Page 2: Important Safety Instructions
35. Battery should not be stored at GUIDE flammable dust) Before each use, carefully inspect 12. Only use Shark® branded filters and temperatures below 3°C (37.4°F) 23. Turn off the vacuum before plugging in or all parts for any damage. If a part is accessories. -
Page 3: Li-Ion Battery
ASSEMBLY LI-ION BATTERY The Lithium Ion Power Pack battery does not come fully charged. Prior to first use, charge completely. 1. Insert Wand into Floor Nozzle. During first use, run the battery down until it is completely out of power. This will condition the battery. 2. -
Page 4: Charging The Battery
SETTINGS CHARGING THE BATTERY USING THE LI-ION CHARGER HARD FLOOR SETTING Hard Floor/Small Area Rugs Slide switch to the bottom to turn off power. LI-ION CHARGER IN HANDHELD VACUUM To begin vacuuming in Standard Mode, slide switch The brushrolls spin slowly to clean bare floors and to the desired setting. -
Page 5: Cleaning Modes
CLEANING MODES USING THE MULTIFLEX® WAND UPRIGHT MODE To clean floors, place foot on floor nozzle and tilt handheld vacuum back. Press the unlock latch on the back of the wand, Adjust the wand to a lower angle to easily clean then adjust the angle. -
Page 6: Maintaining Your Vacuum
MAINTAINING YOUR VACUUM MAINTAINING YOUR VACUUM EMPTYING THE DUST CUP CLEANING THE FILTERS Regularly rinse and replace the filters to maintain your vacuum’s suction power. To clean filters, rinse them with water only. Allow all filters to air-dry completely for at least 24 hours before reinstalling to prevent liquid from being drawn into electric parts. -
Page 7: Maintenance
MAINTAINING YOUR VACUUM MAINTENANCE FLOOR NOZZLE FLOOR NOZZLE CHECKING FOR BLOCKAGES If any hair is wrapped around the brushroll, continue cleaning using the Carpet setting on a bare floor surface, Checking for Blockages in the Handheld Vacuum: a low-pile carpet, or a small area rug. If some fibers remain wrapped around the brushroll after continued use, carefully remove them. -
Page 8: Troubleshooting Guide
TROUBLESHOOTING GUIDE ADDITIONAL ACCESSORIES AVAILABLE ON SHARKACCESSORIES.COM WARNING: To reduce the risk of shock and unintended operation, turn off 8" Crevice Tool power and remove the Lithium Ion Power Pack battery before servicing. 18" Flexi Crevice Tool Duster Crevice Tool Vacuum is not picking up debris. - Page 9 NOTES NOTES s h a r kc l e a n . c o m sharkclean.com...
-
Page 10: Technical Specifications
NOTES REGISTER YOUR PURCHASE sharkclean.com. RECORD THIS INFORMATION TECHNICAL SPECIFICATIONS Voltage: 25.2V Model Number: ����������������������������� Date Code: ��������������������������������� Power: 281W Date of Purchase: ��������������������������� (Keep receipt) Store of Purchase: ��������������������������� TIP: You can find the model and serial numbers on the QR code label on the bottom of the back of the handheld vacuum and battery. - Page 11 For SharkNinja U.S. Patent information, visit sharkninja.com/uspatents © 2020 SharkNinja Operating LLC. DUOCLEAN, MULTIFLEX, and SHARK are registered trademarks of SharkNinja Operating LLC. CLEANTOUCH is a trademark of SharkNinja Operating LLC.