Related Manuals for Shark IZ300UK Series
Summary of Contents for Shark IZ300UK Series
- Page 1 Anti Hair Wrap, DuoClean® & Powerfins ™ Cordless Vacuum IZ300UK Series IZ320UK Series INSTRUCTIONS POWERFINS™...
-
Page 2: Table Of Contents
GUARANTEE, SIMPLY REGISTER YOUR PURCHASE Assembling your Shark® Vacuum Cleaner � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6 Using Your Lithium ION Power Pack Battery sharkclean.co.uk/register-guarantee... -
Page 3: Important Safety Instructions
® electrical wiring, and moving parts that burns. If contact occurs, flush with water. If accessories. Damage caused by non-Shark potentially present risk to the user� liquid contacts eyes, seek medical help. 23 Turn off the vacuum before plugging in or... -
Page 4: Led Battery Power And Charging Indicators
ASSEMBLY LI-ION BATTERY The Lithium ION Power Pack battery does not come fully charged. Prior to first use, charge completely� 1. Insert Wand into Floor Nozzle� During first use, run the battery down until it is completely out of power� This will condition the battery� 2. -
Page 5: Settings
SETTINGS CHARGING THE BATTERY USING THE LI-ION CHARGER POWER ON/OFF HARD FLOOR SETTING Press power button to turn on or off the vacuum� To vacuum in hard floor mode, press the floor select LI-ION CHARGER IN HANDHELD VACUUM button until the hard floor icon ( ) illuminates�... -
Page 6: Cleaning Modes
CLEANING MODES USING THE FLEXOLOGY® WAND FLEXOLOGY REACH UPRIGHT MODE To clean floors, place foot on floor nozzle and tilt handheld vacuum back� Press the unlock latch on the back of the wand, Adjust the wand to a lower angle to easily clean then adjust the angle�... -
Page 7: Maintaining Your Vacuum Cleaner
MAINTAINING YOUR VACUUM MAINTAINING YOUR VACUUM EMPTYING THE DUST CUP CLEANING THE FILTERS Regularly rinse and reinstall the filters to maintain your vacuum’s suction power. To clean filters, rinse them with water only� Allow all filters to air-dry completely before reinstalling to prevent liquid from being drawn into electric parts�... -
Page 8: Checking For Blockages
MAINTAINING YOUR VACUUM MAINTAINING YOUR VACUUM FLOOR NOZZLE FLOOR NOZZLE CHECKING FOR BLOCKAGES If any hair is wrapped around the brushroll, continue cleaning using the Carpet setting on a bare floor surface, Checking for Blockages in the Handheld Vacuum: a low-pile carpet, or a small area rug� If some fibres remain wrapped around the brushroll after continued use, carefully remove them�... -
Page 9: Troubleshooting Guide
TROUBLESHOOTING GUIDE ADDITIONAL ACCESSORIES AVAILABLE ON SHARKACCESSORIES.COM WARNING: To reduce the risk of shock and unintended operation, turn off 8" Crevice Tool power and remove the Lithium ION Power Pack battery before servicing. 18" Flexi Crevice Tool Duster Crevice Tool Vacuum is not picking up debris. -
Page 10: Guarantee
What happens when my guarantee runs out? Shark does not design products to last for a limited time� We do appreciate that there may be a desire for our customers to want to repair their vacuum cleaners after the guarantee has lapsed� In this case please contact our Freephone customer service help line and ask about our out of guarantee programme, on 0800 862 0453�... - Page 11 Illustrations may differ from actual product� We are constantly striving to improve our products; therefore the specifications contained herein are subject to change without notice� © 2021 SharkNinja Operating LLC� DUOCLEAN, FLEXOLOGY and SHARK are registered trademarks of SharkNinja Operating LLC�...
Need help?
Do you have a question about the IZ300UK Series and is the answer not in the manual?
Questions and answers
There is an 5mm jagged shaped stone jammed between the roller with the fins on it and the back teeth/wall of the chamber that roller spins in. It has stopped the movement of that roller. Vacuum has stopped. See no directions as to how to remove that back roller so I can remove the stone. Would be able to get at it if I could get the top lid with the red outline open. Then I could reach the stone. Can not move it from underneath because it is jammed between the little black teeth and the lid. Does not photograph clearly because of the curved lid, but I can see the stone through the lid. All other parts of the vacuum are clear. Please advise as soon as possible. Many thanks. Priscilla Richardson
To remove the Soft Roller on a Shark IZ300UK Series vacuum:
1. Pull the Soft Roller out by the tab.
2. Tap loose debris off the Soft Roller.
3. Use a dry towel to wipe it clean.
This will help clear any jammed stone or debris.
This answer is automatically generated
What does code E2
how to remove the garbage container from handle
To remove the garbage container (dust cup) from the Shark IZ300UK Series handle, press the Dust Cup Release button near the handheld vacuum nozzle. Tilt the dust cup and lift it off to remove.
This answer is automatically generated