Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ojmar NEXO NL1
Summary of Contents for Ojmar NEXO NL1
- Page 1 NL1 Integra INSTALLATION AND ASSEMBLY V1.0...
-
Page 2: Table Of Contents
INDEX 1. NEXO NL1 LOCK INSTALLATION AND ASSEMBLY ....................2 1.1 GENERAL WARNINGS ............................... 2 1.1.1 Regulatory information USA ..........................2 1.1.2 Class B device notice ............................. 2 1.1.3 RF exposure safety ..............................3 1.1.4 TECHNICAL SUPPORT ............................3 1.2 Lock directions ................................3 1.3 Assembly considerations ............................ -
Page 3: Nexo Nl1 Lock Installation And Assembly
1. NEXO NL1 LOCK INSTALLATION AND ASSEMBLY The NEXO NL(X)1 Faceless lock can be installed on doors with thicknesses between 9 mm and 20 mm. The assembly of the lock in the locker door must be correctly carried out to ensure the correct operation of the lock. -
Page 4: Rf Exposure Safety
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 1.1.4 TECHNICAL SUPPORT Should you wish to make any enquiries on our products, please contact the Ojmar technical department: Telephone: +34 943 748 484 ... -
Page 5: Assembly Considerations
1.3.2 Assembly with Magnetic Catch Latch In case of mounting the magnetic Catch Latch, it is necessary to leave a gap “X” of 2/3 mm. between the door and the locker (see following drawing). NEXO NLX1_LOCK INSTALLATION AND ASSEMBLY OJMAR 4... -
Page 6: Procedure For Assembling
1.4 PROCEDURE FOR ASSEMBLING The procedure for assembling a NEXO NL1 lock on a support or furnishing should be performed in this order: Mark the holes as shown in designs 1.2 and 1.3. If necessary, drill the holes to fasten the lock. - Page 7 RFID card to open or close the door. There is two options, depending if Ojmar supplies the adhesive or customer put its own adhesive: 1. Ojmar Adhesive 1.1 Clean the surface of the door and make sure that it is dry.
- Page 8 2.4 Stick the adhesive on the door, making it coincide with the mark made in point 2.2 MOUNTING HOLES FOR RIGHT AND LEFT HAND LOCK Design 1.3 - Measurements given in mm (inches) NEXO NLX1_LOCK INSTALLATION AND ASSEMBLY OJMAR 7...
-
Page 9: Procedure To Unmount The Lock
2 PROCEDURE TO UNMOUNT THE LOCK The steps to follow to disassemble a NEXO NL1 lock on a support or furnishing should be followed in this order: Loosen the two screws on the battery holder using the key provided by Ojmar. - Page 10 After unclipping the cover, use the angular area of the key to push the cover and remove it from the lock. Attach the battery holder with the two screws. Loosen the 4 screws of the lock. NEXO NLX1_LOCK INSTALLATION AND ASSEMBLY OJMAR 9...
-
Page 11: Battery Replacement
Ojmar. Remove the battery holder. Replace the batteries and put the battery holder on again. The NEXO NL1 lock needs 4 AA batteries. Battery recommended by Ojmar: VARTA INDUSTRIAL ALKALINE 1,50 V. SIZE AA LR6. -
Page 12: Cleaning
ATTENTION: In the event of cleaning the installation with water jets, it is necessary for the doors of the installation’s lockers to be closed to keep them free of the effect of corrosive substances that accelerate wear. NEXO NLX1_LOCK INSTALLATION AND ASSEMBLY OJMAR 11... - Page 13 Pol. Ind. Lerun s/n. 20870 Elgoibar · Spain T. +34 943 748484 www.ojmar.com...