Makita DGA701 Instruction Manual page 17

Operation w ith abrasive cut-off /
diamond w heel
Optional accessory
WARNING:
When using an abrasive cut-off
/ diamond w heel, be sure to use only the special
w heel guard designed for use w ith cut-off w heels.
(In some European countries, when using a diamond
wheel, the ordinary guard can be used. Follow the
regulations in your country.)
WARNING:
NEVER use cut-off w heel for side
grinding.
WARNING:
Do not " jam" the w heel or apply
excessive pressure. Do not attempt to make an exces-
sive depth of cut. Overstressing the wheel increases
the loading and susceptibility to twisting or binding of the
wheel in the cut and the possibility of kickback, wheel
breakage and overheating of the motor may occur.
WARNING:
Do not start the cutting operation
in the w orkpiece. Let the w heel reach full speed and
carefully enter into the cut moving the tool forw ard
over the w orkpiece surface. The wheel may bind, walk
up or kickback if the power tool is started in the workpiece.
WARNING:
During cutting operations, never
change the angle of the w heel. Placing side pressure
on the cut-off wheel (as in grinding) will cause the wheel
to crack and break, causing serious personal injury.
WARNING:
A diamond w heel shall be oper-
ated perpendicular to the material being cut.
Mount the inner flange onto the spindle.
Fit the wheel / disc on the inner flange and screw the
lock nut onto the spindle.
Fig.23: 1. Lock nut 2. Abrasive cut-off wheel / dia-
mond wheel 3. Inner flange 4. Wheel guard
for abrasive cut-off wheel / diamond wheel
For Australia and New Zealand
Fig.24: 1. Lock nut 2. Outer flange
wheel / diamond wheel 4. Inner flange
guard for abrasive cut-off wheel / diamond wheel
Operation w ith w ire cup brush
Optional accessory
CAUTION:
Check operation of brush by run-
ning tool w ith no load, insuring that no one is in
front of or in line w ith brush.
CAUTION:
Do not use brush that is damaged, or
w hich is out of balance. Use of damaged brush could increase
potential for injury from contact with broken brush wires.
Fig.25: 1. Wire cup brush
Remove the battery cartridge and place the tool upside
down allowing easy access to spindle.
Remove any accessories on spindle. Thread wire cup
brush onto spindle and tighten with supplied wrench.
NOTICE:
Avoid applying too much pressure
w hich causes over bending of w ires w hen using
brush. It may lead to premature breakage.
Operation w ith w ire w heel brush
Optional accessory
brush by running tool w ith no load, insuring that
no one is in front of or in line w ith the w ire w heel
brush.
is damaged, or w hich is out of balance. Use of
damaged wire wheel brush could increase potential
for injury from contact with broken wires.
wheel brushes, assuring diameter of wheel fits
inside guard. Wheel can shatter during use and
guard helps to reduce chances of personal injury.
Remove the battery cartridge and place the tool upside
down allowing easy access to spindle.
Remove any accessories on spindle. Thread wire wheel
brush onto spindle and tighten with the wrenches.
NOTICE:
w hich causes over bending of w ires w hen
using w ire w heel brush. It may lead to premature
breakage.
Operating w ith offset diamond
w heel
Optional accessory
With optional accessories, you can use this tool for
planing concrete surface.
are 7 mm or thinner, place the convex section of
the lock nut up w ards and attach to the spindle.
3. Abrasive cut-off
offset diamond w heel is only for use in planing
5. Wheel
concrete surface w ith a offset diamond w heel. Do
not use this guard w ith any other cutting acces-
sory or for any other purpose.
a vacuum cleaner is connected to the tool and
turned on.
Remove the battery cartridge and install the dust col-
lecting wheel guard for the offset diamond wheel.
Mount the inner flange onto the spindle. Fit the offset
diamond wheel on the inner flange and tighten the lock
nut onto the spindle.
17 ENGLISH
CAUTION:
Check operation of w ire w heel
CAUTION:
Do not use w ire w heel brush that
CAUTION:
ALWAYS use guard w ith w ire
Fig.26: 1. Wire wheel brush
Avoid applying too much pressure
WARNING:
For offset diamond w heels that
CAUTION:
Dust collecting w heel guard for the
CAUTION:
Before operation, make sure that
Fig.27: 1. Lock nut 2. Conve x section 3. Offset
diamond wheel 4. Inner flange 5. Spindle
6. Dust collecting wheel guard for the offset
diamond wheel 7. Shaft lock