Horizon Hobby Blade Fusion 360 SMART Instruction Manual

Horizon Hobby Blade Fusion 360 SMART Instruction Manual

Hide thumbs Also See for Blade Fusion 360 SMART:

Advertisement

Instruction Manual
Bedienungsanleitung
Manuel d'utilisation
Manuale di Istruzioni

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Blade Fusion 360 SMART and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Horizon Hobby Blade Fusion 360 SMART

  • Page 1 Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni...
  • Page 2 ™ Horizon Hobby product, always purchase from Horizon Hobby, LLC or a Horizon Hobby authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM ®...
  • Page 3: Table Of Contents

    Warranty and Service Contact Information ......19 Panic Recovery ..............9 FCC Information ..............19 Pre-Flight Checklist ............9 IC Information ..............19 Flying the Blade Fusion 360 SMART ........10 Compliance Information for the European Union ....20 Gyro Gain Adjustment .............10 Specifications Length 26.9 in (685mm) Main Rotor Diameter 31.3 in (796mm)
  • Page 4: First Flight Preparation

    First Flight Preparation Flying Checklist • Remove and inspect contents ❏ Always turn the transmitter on first • Begin charging the flight battery (not included) ❏ Plug the flight battery into the lead from the ESC • Install the flight battery in the helicopter ❏...
  • Page 5: Electronic Speed Controller Governor Operation

    Electronic Speed Controller Governor Operation The included electronic speed controller (ESC) utilizes a The default throttle curve settings listed in the transmitter head speed governor to maintain a constant head speed setup tables should be acceptable to most pilots and during flight.
  • Page 6 DX6G2, DX6e, DX7G2, DX8G2, DX8e, DX9, DX18, DX20, NX6, NX8, NX10, iX12, iX20 SYSTEM SETUP FUNCTION LIST Servo Setup Model Type HELI Channel Travel Reverse Channel Travel Reverse Swash Type Normal 100/100 Normal 100/100 Normal F-Mode Setup 100/100 Normal AX2* 100/100 Normal Switch 1...
  • Page 7: Installing The Flight Battery

    Installing the Flight Battery 1. Lower the throttle. 7. The swashplate will center, indicating that the unit is 2. Power on the transmitter. ready. The flight controller status LED will display a slow 3. Center all trims. green flash once initialization has been completed. 4.
  • Page 8: Throttle Hold

    Throttle Hold Throttle hold is used to prevent the motor from powering on Throttle hold is also used to turn off the motor quickly if the inadvertently. For safety, turn throttle hold ON any time you helicopter is out of control, in danger of crashing, or both. need to touch the helicopter or check the direction controls.
  • Page 9: Panic Recovery

    Collective Pitch Front View Front View Collective pitch up Collective pitch down Motor Test Place the helicopter outdoors on a clean, flat and level WARNING: Stay at least 30 feet (10 meters) surface (concrete or asphalt) free of obstructions. Always away from the helicopter when the motor is stay clear of moving rotor blades.
  • Page 10: Flying The Blade Fusion 360 Smart

    Always stay at least 30 feet (10 meters) away flight control. from the helicopter when it is flying. Landing The Blade Fusion 360 SMART is intended to be flown Establish a low level hover. Deliberately lower the throttle outdoors by experienced pilots. until the helicopter lands.
  • Page 11: Post-Flight Inspections And Maintenance

    Post-Flight Inspections and Maintenance Make sure the plastic ball link holds the control ball, but is not tight (binding) on the ball. When a link Ball Links is too loose on the ball, it can separate from the ball during flight and cause a crash. Replace worn ball links before they fail.
  • Page 12: Advanced Tuning (Non-Forward Programming)

    Advanced Tuning (Non-Forward Programming) Applies to Spektrum transmitters not capable of forward programing including DX6i, DX7s DX8 Your Blade Fusion 360 was setup at the factory and test flown. The servo adjustment steps are usually only necessary in special circumstances, such as after a crash or if a servo or linkage is replaced. For pilots flying with a transmitter not capable of forward programming use the following procedures to make servo adjustments and perform the calibration procedure.
  • Page 13: Flight Mode And Rate Selection

    Calibration Procedure (Non-Forward Programming) If the helicopter is experiencing drift issues after completing the trim flight procedure, perform the following calibration. The calibration procedure may also be needed following crash repairs. To perform the calibration procedure: 1. Ensure the surface used for calibration is level. 6.
  • Page 14: Troubleshooting Guide

    Troubleshooting Guide Problem Possible Cause Solution Low flight battery or transmitter Fully charge or replace the flight battery and/or transmitter battery voltage batteries Power on the transmitter while holding the Trainer/Bind Helicopter will not bind Transmitter is not in bind mode switch.
  • Page 15: Exploded View

    Exploded View...
  • Page 16 45mm 38mm 38mm 45mm...
  • Page 17: Parts List

    Parts List Part # Description Part # Description 1 BLH1620 3x8x3.5 Thrust Bearing (2) 23 BLH5213 Tail Rotor Hub: Fusion 360 2 BLH1645 Landing Gear Set: B450 24 BLH5214 Tail Pitch Slider: Fusion 360 3 BLH4705 Spindle Set (2): 360 CFX 25 BLH5215 Rear Tail Case: Fusion 360 4 BLH4710...
  • Page 18: Limited Warranty

    For questions or assistance, please visit our website Horizon Hobby, LLC, (Horizon) warrants to the original purchaser at www.horizonhobby.com, submit a Product Support Inquiry, or that the product purchased (the “Product”) will be free from call the toll free telephone number referenced in the Warranty defects in materials and workmanship at the date of purchase.
  • Page 19: Warranty And Service Contact Information

    Supplier’s Declaration of Conformity which can be determined by turning the equipment Blade Fusion 360 SMART BNF (BLH6150) off and on, the user is encouraged to try to correct the This device complies with part 15 of the FCC interference by one or more of the following measures: Rules.
  • Page 20: Compliance Information For The European Union

    Compliance Information for the European Union EU Manufacturer of Record: EU Compliance Statement: Horizon Hobby, LLC Blade Fusion 360 SMART BNF (BLH6150); 2904 Research Road Hereby, Horizon Hobby, LLC declares Champaign, IL 61822 USA that the device is in compliance with the following: EU Radio Equipment Directive 2014/53/EU;...
  • Page 21 Blade, the Blade logo, Fusion, DSM, DSM2, DSMX, Bind-N-Fly, IC3, EC3, Spektrum AirWare, SAFE, BNF, the BNF logo, ModelMatch and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc.

Table of Contents