Directed GM10 Firmware Specific Manual
  1. Manuals
  2. Brands
  3. Directed Manuals
  4. Automobile Accessories
  5. GM10
  6. Firmware specific manual
Directed GM10 Firmware Specific Manual

Directed GM10 Firmware Specific Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Directed Digital System
GM10
Firmware Specific Guide
This product is intended for installation by a professional
installer only! Attempts to install this product by a person
other than a trained professional may result in severe
damage to a vehicle's electrical system and components.
© 2015 Directed, Vista, CA
Directed Digital System 2015-10

Advertisement

Table of Contents
loading

Related Manuals for Directed GM10

Summary of Contents for Directed GM10

  • Page 1 This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components. © 2015 Directed, Vista, CA Directed Digital System 2015-10...

  • Page 2: Table Of Contents

    Contents Warning! Safety first ........................3 Introduction ............................ 4 Vehicle application guide ......................4 Wiring connections ......................... 5 Main power harness (H1), 12-pin thick gauge connector ............... 5 Auxiliary output harness (H2), 16-pin black connector ..............5 Analog harness (H3), 18-pin white connector ................6 MC501 harness (H4), 8 thick-gauge wires (optional) ..............

  • Page 3: Warning! Safety First

    This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately.

  • Page 4: Introduction

    Introduction The GM10 firmware for Directed Digital Systems is a complete solution for remote start, security (if applicable), bypass interface, and convenience needs compatible with specific Buick, Chevrolet and GMC vehicles. Warning! This module can only be programmed via the web tool, which can be found on www.directechs.com or using the Directechs Mobile application for smartphones.

  • Page 5: Wiring Connections

    If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. Directed Digital System GM10 © 2015 Directed. All rights reserved.

  • Page 6: Analog Harness (H3), 18-Pin White Connector

    These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" starting on pages 4 to for a list of compatible features. Directed Digital System GM10 © 2015 Directed. All rights reserved.

  • Page 7: Installation

    The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. The siren is only available with the Directed Digital System remote start and security system. If RAP Off wire is not connected, radio will turn OFF but some lights will remain ON in the center console for 10 minutes. Connect the Lt.Blue/Black wire to the driver door sense trigger to avoid the issue.

  • Page 8: Type 1B (With T-Harness Thgm610C - Rev. 1)

    The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. The siren is only available with the Directed Digital System remote start and security system. If RAP Off wire is not connected, radio will turn OFF but some lights will remain ON in the center console for 10 minutes. Connect the Lt.Green/Black wire to the driver door sense trigger to avoid the issue.

  • Page 9: Type 1C (With T-Harness Thgm610C - Rev. 2)

    The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. The siren is only available with the Directed Digital System remote start and security system. 20 21 Only required if NOT equipped with OnStar.

  • Page 10: Type 2A (Without T-Harness)

    The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. The siren is only available with the Directed Digital System remote start and security system. Only if NOT equipped with OnStar.

  • Page 11: Type 2B (With T-Harness Thgm610C - Rev. 1)

    The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. The siren is only available with the Directed Digital System remote start and security system. 20 21 Only required if NOT equipped with OnStar.

  • Page 12: Type 2C (With T-Harness Thgm610C - Rev. 2)

    The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. The siren is only available with the Directed Digital System remote start and security system. If RAP Off wire is not connected, radio will turn OFF but some lights will remain ON in the center console for 10 minutes. Connect the Lt.Green/Black wire to the driver door sense trigger to avoid the issue.

  • Page 13: Type 3

    The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. The siren is only available with the Directed Digital System remote start and security system. If RAP Off wire is not connected, radio will turn OFF but some lights will remain ON in the center console for 10 minutes. Connect the Lt.Blue/Black wire to the driver door sense trigger to avoid the issue.

  • Page 14: Vehicle Wiring Reference Charts

    Immo. Control Module, under Ignition Switch RAP Off Gray Black Driver Window Motor SW CAN Green Black OBDII Connector CAN High Dk. Blue Black OBDII Connector CAN Low White Black OBDII Connector Directed Digital System GM10 © 2015 Directed. All rights reserved.
  • Page 15 Immo. Control Module, under Ignition Switch RAP Off Black Gray Driver Window Motor SW CAN Black Green OBDII Connector CAN High Black Blue OBDII Connector CAN Low White Black OBDII Connector Directed Digital System GM10 © 2015 Directed. All rights reserved.
  • Page 16 Immo. Control Module, under Ignition Switch RAP Off Gray/Black Black Driver Window Switch SW CAN Dk. Green Black OBDII Connector CAN High Tan/Black Black OBDII Connector CAN Low Black OBDII Connector Directed Digital System GM10 © 2015 Directed. All rights reserved.
  • Page 17 BCM - under driver dash (without power windows) RAP Off Black Gray Driver Window Motor (with power windows) SW CAN Green Black OBDII Connector CAN High Blue Black OBDII Connector CAN Low White Black OBDII Connector Directed Digital System GM10 © 2015 Directed. All rights reserved.
  • Page 18 BCM - under driver dash (without power windows) RAP Off Gray Black Driver Window Motor (with power windows) SW CAN Green Black OBDII Connector CAN High Blue Black OBDII Connector CAN Low White Black OBDII Connector Directed Digital System GM10 © 2015 Directed. All rights reserved.
  • Page 19 BCM - under driver dash (without power windows) RAP Off Gray Black Driver Window Motor (with power windows) SW CAN Green Black OBDII Connector CAN High Blue Black OBDII Connector CAN Low White Black OBDII Connector Directed Digital System GM10 © 2015 Directed. All rights reserved.
  • Page 20 BCM - under driver dash (without power windows) RAP Off Gray Black Driver Window Motor (with power windows) SW CAN Green Black OBDII Connector CAN High Blue Black OBDII Connector CAN Low White Black OBDII Connector Directed Digital System GM10 © 2015 Directed. All rights reserved.

  • Page 21: Important

    Manual or automatic transmission selection The yellow loop on the Directed Digital System controls which transmission type the unit is configured for. The state of the loop (uncut or cut) when the main module is powered up will determine which type is selected.

  • Page 22: Rf Kits

    Please follow the instructions included with the kit for appropriate installation and programming information. When flashing the Directed Digital System, make sure to pick the remote you will be using. This way the main module will have the necessary firmware to interact with the remote and Control Center (antenna) combination.

  • Page 23: Module Programming

    Connect all but the white 12-pin harness Connect all the harnesses to the Directed Digital System, EXCEPT the white12-pin main power harness. Must be connected LAST Connect the white12-pin main power harness, and wait until &...

  • Page 24: Led Diagnostics And Troubleshooting

    Cycle was done slower than 5 seconds, reset Key Cycle out of time or remote out of Key Cycle timeout. module and retry module programming from step range. Flashes red x 1 and orange x 2 Directed Digital System GM10 © 2015 Directed. All rights reserved.
  • Page 25 If the bypass module fails to flash, it means Commands can come from RF or D2D. received. the module did not receive the signal. Flashes orange AUX1 command received. Flashes orange AUX2 command received. Flashes orange Directed Digital System GM10 © 2015 Directed. All rights reserved.

  • Page 26: Module Reset

    After 3 seconds the LED turns ON solid orange. Keep holding the & & programming button until the LED flashes red, then orange slowly. Solid Hold Flashes Release the programming button. The LED turns ON solid red. & Solid Release Directed Digital System GM10 © 2015 Directed. All rights reserved.

  • Page 27: Learning The Tach (Not Needed With Virtual Tach)

    Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature in the configuration wizard to adjust the starter output time in 50mS increments to compensate for such an occurrence. Directed Digital System GM10 © 2015 Directed. All rights reserved.

  • Page 28: Limited Lifetime Consumer Warranty

    Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;...

  • Page 29: Quick Reference Guide - Viper, Clifford, Python, Avital & Automate

    Press the Lock button on the factory or aftermarket remote.* Press Lock on The vehicle engine will shut Off after locking either remote* the system. * Your aftermarket remote may differ from the model shown in the illustrations. Directed Digital System GM10 © 2015 Directed. All rights reserved.
  • Page 30 Pit stop mode SmartStart compatible This system is compatible with Directed SmartStart 3.0. For a complete list of Stop the vehicle in a safe parking spot and put the supported features, please visit www.mysmartstart.com. gear in Park (P). On manual transmission vehicle,...

  • Page 31: Quick Reference Guide - Autostart

    Press Lock to shut vehicle Off or Trunk (aftermarket remote lock the doors and enter idle mode. only) to enter idle mode * Your aftermarket remote may differ from the model shown in the illustrations. Directed Digital System GM10 © 2015 Directed. All rights reserved.
  • Page 32 Stop the vehicle in a safe parking spot and put the gear in gear in Park (P). Park This system is compatible with Directed SmartStart 3.0. For a complete list of supported features, please visit www.mysmartstart.com. Press the Remote Start button on the transmitter.* What is SmartStart? 14:36 &...

Table of Contents