Shuttle AB60N User Manual
  1. Manuals
  2. Brands
  3. Shuttle Manuals
  4. Motherboard
  5. AB60N
  6. User manual

Shuttle AB60N User Manual

Pentium 4/celeron 478-pin processor based main board
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
AB60N
Pentium 4/Celeron
Based MAIN BOARD
478-pin
Processor
User's Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AB60N and is the answer not in the manual?

Questions and answers

Related Manuals for Shuttle AB60N

Summary of Contents for Shuttle AB60N

  • Page 1 AB60N Pentium 4/Celeron Based MAIN BOARD 478-pin Processor User's Manual...
  • Page 2 The information contained in this manual is provided for general use by the customers. Trademarks Shuttle is a registered trademark of Shuttle Inc. Intel, Pentium is a registered trademarks of Intel Corporation. PS/2 is a registered trademark of IBM Corporation.
  • Page 3 Statement of Shuttle Mainboard via the EMI Test Shuttle mainboards have been via the EMI test in terms of series of regulations: EN55022/ CISPR22/AS/NZS3548 Class B, EN55024 (1998/AS/NZS), EN4252.1 (1994), EN61000, ANSI C63.4 (1992), CFR47 Part 15 Subpart B, and CNS13438 (1997). The items tested are illus- trated as follows: (A) Voltage: AC 110V/60HZ &...
  • Page 4 Remedy: N/A EMI Interference: Crystal: 14.318MHz(X2)/ 25.00MHz(X4)/ 32.768KHz(X1) Clock Generator: CLK1 (D) Supported Host Peripherals: Host Peripheral Product Name Model Name FCC ID Case AB60N Power Supply (300W) AM630BS20S 0005596 D33047 Maxtor HDD (40 GB) D740X-6L 3902B975 Panasonic FDD JU-257A606P...

  • Page 5: Table Of Contents

    2.1 SPECIFICATIONS ..................8 3 HARDWARE INSTALLATION ............11 3.1 STEP BY STEP INSTALLATION ..............11 Accessories of AB60N ................11 STEP 1 Install the CPU ................12 STEP 2 Set Jumpers ................14 STEP 3 Install Dual Channel DDR System Memory ........ 14 STEP 4 Install Peripherals in System Case ..........
  • Page 6 3.2 JUMPER SETTINGS ................. 25 JUMPERS & CONNECTORS GUIDE ............ 26 Jumpers Clear CMOS Setting (JP2) ..............29 LAN Select On Board Setting (JP4) ............29 Back-Panel Connectors PS/2 Keyboard & PS/2 Mouse Connectors ..........30 Parallel Port Connector ................30 COM1/2 Port Connectors ..............
  • Page 7 Other Connectors ATX Power Supply Connectors (ATX1 & ATX2) ........36 Cooling Fan Connectors for Chipset (FAN1), CPU (FAN2), AGP(FAN3), System(FAN4) ..................37 IR Header (J1) ..................37 Wake-On-LAN Header (WOL1) ............. 38 CD-IN Connectors (J7/J8) ..............38 Audio Auxiliary_IN Connector (J9) ............39 Center/Bass_Out Header (J6)...............
  • Page 8 5.2 THE MAIN MENU ..................51 STANDARD CMOS FEATURES ............... 53 ADVANCED BIOS FEATURES ..............57 ADVANCED CHIPSET FEATURES ............61 INTEGRATED PERIPHERALS ..............64 POWER MANAGEMENT SETUP .............. 70 PNP/PCI CONFIGURATION............... 75 PC HEALTH STATUS ................77 FREQUENCY/VOLTAGE CONTROL ............78 LOAD FAIL-SAFE DEFAULTS ..............

  • Page 9: What's In The Manual

    WHAT'S IN THE MANUAL Quick Reference Hardware Installation >> Step-by-Step ..........Page 11 Jumper Settings >> A Closer Look ............Page 25 Drivers/Software Utilities >> How to Install ......... Page 43 BIOS Setup >> How to Configure ............Page 50 About This Manual For First-Time DIY System Builder ............

  • Page 10: Introduction

    Shuttle AB60N mainboard. Experienced DIY User Congratulate on your purchase of the Shuttle AB60N mainboard. You will find that installing your new Shuttle AB60N mainboard is just easy. Bundled with an array of onboard functions, the highly-integrated AB60N mainboard pro- vides you with a total solution to build the most stable and reliable system.

  • Page 11: Item Checklist

    1.2 Item Checklist Check all items with your AB60N mainboard to make sure nothing is missing. The complete package should include: DIMM1 DIMM2 DIMM1 DIMM2 FAN2 COM1 FAN1 - One piece of Shuttle AB60N Mainboard JUSB1 JUSB2LAN1 AUDIO1 ATX2 FAN3...

  • Page 12: Features

    2 FEATURES AB60N mainboard is carefully designed for the demanding PC user who wants high perfor- mance and maximum intelligent features in a compact package. 2.1 Specifications - CPU Support Intel Pentium 4/Celeron, 478-pin processors with 400/533/800 MHz FSB. Don't support willmette CPU.
  • Page 13 Ø 1 X Floppy interface for 3.5-inch FDD with 720KB, 1.44MB, or 2.88MB format or for 5.25-inch FDD with 360K or 1.2MB format. Ø 1 X PS/2 mouse connector. Ø 1 X PS/2 Keyboard connector. Ø 4 X USB ports. Ø...
  • Page 14 - Advanced Features Ø Low EMI - Built in spread spectrum and automatic clock shut-off of unused PCI/DDR-SDRAMS slots to reduce EMI. Ø Dual Function Power Button - The system can be in one of two states, one is Suspend mode and the other is Soft-Off mode. Pushing the power button for less than 4 seconds places the system into Suspend mode.

  • Page 15: Hardware Installation

    Then follow these steps designed to guide you through a quick and correct installation of your system. 3.1 Step-by-Step Installation Accessories Of AB60N CPU FAN - FAN2 Chipset FAN - FAN1 Four DIMM Slots...

  • Page 16: Step 1 Install The Cpu

    Step 1 CPU Installation: This mainboard supports Intel Pentium 4/Celeron , Socket 478 series CPU. Please follow the step as below to finish CPU installation. Be careful of CPU orientation when you plug it into CPU socket. 1. Pull up the CPU socket lever and up to 90-degree angle. CPU socket lever up to 90 degree 2.
  • Page 17 3. Press down the CPU socket lever and finish CPU installation. Note: If you do not match the CPU socket Pin 1 and CPU cut edge well, it may damage the CPU. 4. The Intel Pentium 4/Celeron processor requires a set of heatsink/fan to en sure proper cooling of the processor.

  • Page 18: Step 2 Set Jumpers

    Step 2. Set Jumpers This mainboard is jumperless! The default jumper settings have been set for the common usage standard of this mainboard. Therefore, you do not need to reset the jumpers unless you require special adjustments as any of the following cases: 1.

  • Page 19: Step 4 Install Peripherals In System Case

    Step 4 Install Internal Peripherals in System Case Before you install and connect the mainboard into your system case, we rec- ommend that you first assemble all the internal peripheral devices into the com- puter housing, including but not limited to the hard disk drive (IDE/HDD), floppy disk drive (FDD), CD-ROM drive, and ATX power supply unit.

  • Page 20: Step 5 Mount The Mainboard On The Computer Chassis

    Step 5 Mount the Mainboard on the Computer Chassis 1. You may find that there are a lot of different mounting hole positions both on your computer chassis and on the mainboard. To choose correct mounting holes, the key point is to keep the back-panel of the mainboard in a close fit with your system case, as shown below.

  • Page 21: Step 6 Connect Front Panel Switches/Leds/Speaker/Usb

    Step 6 Connect Front Panel Switches/LEDs/Speaker/USB connectors You can find there are several different cables already existing in the system case and originating from the computer's front-panel devices (HDD LED, Power LED, Reset Switch, PC Speaker, or USB devices etc.) These cables serve to con- nect the front-panel switches, LEDs, and USB connectors to the mainboard's front-panel connectors group, as shown below.

  • Page 22: Step 7 Connect Ide And Floppy Disk Drives

    Step 7 Connect IDE and Floppy Disk Drives 1. IDE cable connector 2. Floppy cable connector 3. Serial ATA cable connector - 18 -...

  • Page 23: Step 8 Connect Other Internal Peripherals

    Step 8 Connect Other Internal Peripherals 1. CD-IN, AUX-IN, Center/Bass audio headers CENTER/BASS CD-IN AUX-IN CD-IN 2. IR header - 19 -...
  • Page 24 3. SPDIF In/Out header SPDIF 4. Wake-On-LAN header WOL1 5. Front Panel Audio header Front Panel Audio - 20 -...

  • Page 25: Step 9 Connect The Power Supply

    Step 9 Connect the Power Supply 1. System power connector ATX2 Step 10 Install Add-on Cards in Expansion Slots 1. Accelerated Graphics Port (AGP) Card 2. PCI Card - 21 -...

  • Page 26: Step 11 Connect External Peripherals To Back Panel

    Step 11 Connect External Peripherals to Back-Panel You are now ready to put the computer case back together and get on to the external peripherals connections to your system's back-panel. 1. PS/2 Mouse & PS/2 Keyboard 2. Parallel Port 3. COM1 Port 4.

  • Page 27: Step 12 First Time System Boot Up

    Step 12 First Time System Boot Up To assure the completeness and correctness of your system installation, you may check the above installation steps once again before you boot up your system for the first time. 1. Insert a bootable system floppy disk (DOS 6.2x, Windows 95/98/NT, or others) which contains FDISK and FORMAT utilities into the FDD.

  • Page 28: Step 13 Install Drivers & Software Components

    /2000/ME/XP/NT operating systems only. Make sure your operating system is already installed before running the drivers installation CD-ROM programs. 1. Insert the AB60N bundled CD-ROM into your CD-ROM drive. The autorun program will display the drivers main installation window on screen.

  • Page 29: Jumper Settings

    3.2 Jumper Settings Several hardware settings are made through the use of jumper caps to connect jumper pins to the mainboard. Pin #1 could be located at any corner of each jumper; you just find a location marked with a while right angle, which stands for pin1#.

  • Page 30: Jumpers & Connectors Guide

    Jumpers & Connectors Guide Use the mainboard layout on page 11 to locate CPU socket, memory banks, expansion slots, jumpers and connectors on the mainboard during the installa- tion. The following list will help you to identify jumpers, slots, and connectors along with their assigned functions: B2~B4 B6~B7...

  • Page 31: Jumpers

    Jumpers : Clear CMOS setting : LAN Enable/Disable Back Panel Connectors : PS/2 keyboard port : PS/2 mouse port Parallel : Printer port COM1 : Serial port COM2 : Serial port USB1/2 : 2x USB ports : LAN port USB3/4 : 2x USB ports LINE-OUT : Line-out port (Front Out)
  • Page 32 Other Connectors ATX1/ATX2 : ATX power connectors FAN1 : Chipset fan connector FAN2 : CPU fan connector FAN3 : AGP fan connector FAN4 : System fan connector : IR header WOL1 : Wake-On-LAN connector J7/J8 : CD-IN 1/2 headers : AUX-IN header : Center/Bass audio header : Front Panel Audio header : SPDIF In/Out header...

  • Page 33: Clear Cmos Setting (Jp2)

    Jumpers Clear CMOS Setting (JP2) JP2is used to clear CMOS data. Clearing CMOS will result in the permanently erasing previous system configuration settings and the restoring original(factory- set) system settings. Pin 1-2 (Default) Pin 2-3 (Clear CMOS) Step 1. Turn off the system power (PC-> Off). Step 2.

  • Page 34: Back-Panel Connectors Ps/2 Keyboard & Ps/2 Mouse Connectors

    Back-Panel Connectors PS/2 Keyboard & PS/2 Mouse Connectors Two 6-pin female PS/2 keyboard & Mouse connectors are located at the rear panel PS/2 Mouse of the mainboard. Depending on the com- puter housing you use (desktop or tower), the PS/2 Mouse connector is situated at the top of the PS/2 Keyboard connector when the mainboard is laid into a desk- top, as opposed to a tower where the PS/2...

  • Page 35: Lan Port Connector

    LAN Port Connector This mainboard can accommodate one device on LAN. Attach a 10/100 baseT cable to the RJ45 LAN port at the back-panel of your computer. USB3/USB4 Port Connectors USB port4 This mainboard offers 2 USB ports on back panel.

  • Page 36: Front-Panel Connectors Hdd Led Connector (Hled)

    Front-Panel Connectors HDD LED Connector (HLED) Attach the connector cable from the IDE device LED to the 2-pin (HLED) header. The HDD LED lights up whenever an IDE device is active. Front Panel SPEAKER EPMI RST HLED GLED Hardware Reset Connector (RST) Attach the 2-pin hardware reset switch cable to the (RST) header.

  • Page 37: Speaker Connector (Speaker)

    Speaker Connector (SPEAKER) Attach the PC speaker cable from the case to the 4-pin speaker connector (SPEAKER). Front Panel SPEAKER EPMI RST HLED GLED Green LED Connector (GLED) The Green LED (GLED) Indicates that the system in currently in one of the power saving modes (Doze/Standby/Suspend).

  • Page 38: Power Led Connector (Pwrled)

    Power LED Connector (PWRLED) Attach the 3-pin Power-LED connector cable from the housing front-panel to the (PWRLED) header on the mainboard. The power LED stays light while the system is running. Front Panel SPEAKER EPMI RST HLED GLED Extended USB Connectors (JUSB3/JUSB4) The headers are used to connect the cable attached to USB connectors which are mounted on front-panel or back-panel.

  • Page 39: Internal Peripherals Connectors Enhanced Ide And Floppy Connectors

    Internal Peripherals Connectors Enhanced IDE and Floppy Connectors The mainboard features two 40-pin dual-channel IDE device connectors (IDE1/ IDE2) providing support for up to four IDE devices, such as CD-ROM and Hard Disk Drives (H.D.D.). This mainboard also includes one 34-pin floppy disk controller (FDD1) to ac- commodate the Floppy Disk Drive (FDD).

  • Page 40: Other Connectors Atx Power Supply Connectors (Atx1 & Atx2)

    Other Connectors ATX Power Supply Connectors (ATX1 & ATX2) This motherboard uses 20-pin Pentium 4 standard ATX power header, and ATX2 with 2x2-pin PC ATX power supply headers. Please make sure you plug in the right direction. ATX1 ATX2 ATX2 Note 1 : The ATX power connector is directional and will not go in unless the guides match perfectly making sure that pin#1 is properly positioned.

  • Page 41: Cooling Fan Connectors For Chipset (Fan1), Cpu (Fan2), Agp(Fan3), System(Fan4)

    CPU, CAS, and PWR Fan connectors (FAN1/FAN2/FAN3/FAN4) The mainboard provides four onboard 12V cooling fan power connectors to support Chipset(FAN1) , CPU(FAN2), AGP(Fan3) and System(FAN4) cooling fans. FAN1 FAN2 Note: Both cable wiring and type of plug may vary , which depends on the fan maker.

  • Page 42: Wake-On-Lan Header (Wol1)

    Wake-On-LAN Connector (WOL1) Attach a 3-pin connector through the LAN card which supports the Wake-On- LAN (WOL1) function. This function lets users wake up the connected system through the LAN card. Pins Assignment: 1=5VSB 2=GND WOL1 3=RING# CD_IN Connectors (J7/J8) Port J7/J8 is used to attach an audio connector cable from the CD-ROM drive.

  • Page 43: Audio Auxiliary_In Connector (J9)

    Audio AUXILIARY_IN Connector (J9) Port J9 can be used to connect a stereo audio input from CD-ROM, TV-tuner or MPEG card. Pin Assignments: 1=AUXL AUX-IN 2=AGND 3=AGND 4=AUXR Center/Bass_Out Header (J6) J6 header can be used to connect the cable which attached to center/bass am- plified speakers.

  • Page 44: Front Panel Audio Connector (J4)

    Front Panel Audio Connector (J4) This header allows the user to install auxiliary front-oriented micorophone and line-out ports for easier access. Pin Assignments: 1=AUD_MIC Front Audio 2=AUD_GND 3=AUD_MIC_BIAS 4=AUD_VCC 5=AUD_FPOUT_R 6= AUD_RET_R 7=NC 8=KEY 9=AUD_FPOUT_L 10=AUD_RET_L Two mini jumpers must be setted on pin 5-6 and pin 9-10, when this header is not used.

  • Page 45: System Memory Configuration

    3.3 System Memory Configuration The AB60N mainboard has four 184-pin DIMM slots that allow you to install from 64MB up to 4GB of system memory. Each 184-pin DIMM (Dual In-line Memory Module) Slot can accommodate 64MB, 128MB, 256MB, 512MB, and 1GB of PC2100, PC2700 or PC3200 compliant 2.5V single (1 Bank) or double...

  • Page 46: Upgrade Memory

    Dual channel memory controller configuration: All the other case: 1. Running in Dual Channel Mode The DIMM must be the same memory size and the same type to let this function work. DIMM1 DIMM2 DIMM2 DIMM1 DIMM2 DIMM1 CH A CH A CH A CH B...

  • Page 47: Software Utility

    4 SOFTWARE UTILITY 4.1 Mainboard CD Overview Note : The CD contents attached in AB60N mainboard are subject to change without notice. To start your mainboard CD disc, just insert it into your CD-ROM drive and the CD AutoRun screen should appear. If the AutoRun screen does not appear, double click or run D:\Autorun.exe (assuming that your CD-ROM drive is...

  • Page 48: Install Mainboard Software

    Insert the attached CD into your CD-ROM drive and the CD AutoRun screen should appear. If the AutoRun screen does not appear, double click on Autorun icon in My Computer to bring up Shuttle Mainboard Software Setup screen. Select using your pointing device (e.g. mouse) on the "Install Mainboard Software"...

  • Page 49: A Install Intel Chipset Driver

    4.2.A Install Intel Chipset Driver Select using your pointing device (e.g. mouse) on the "Install Intel Chipset Driver" bar to install Intel chipset driver. Once you made your selection, a Setup window run the installation automati- cally. When the copying files is done, make sure you reboot the system to take the installation effect.

  • Page 50: C Install Realtek Audio Driver

    4.2.C Install Realtek Audio Driver Select using your pointing device (e.g. mouse) on the "Install Realtek Audio Driver" bar to install audio driver. Once you made your selection, a Setup window run the installation automati- cally. When the copying files is done, make sure you reboot the system to take the installation effect.

  • Page 51: Install Utility

    Insert the attached CD into your CD-ROM drive and the CD AutoRun screen should appear. If the AutoRun screen does not appear, double click on AutoRun icon in My Computer to bring up Shuttle Mainboard Software Setup screen. Select using your pointing device (e.g. mouse) on the "Install Utility" bar to run into sub-menu.

  • Page 52: A Install Acrobat Reader

    4.3.A Install Acrobat Reader Click on the "Install Acrobat Reader" bar if you need to install Acrobat Reader. 4.3.B Install WinFlash Utility Click on the "Install WinFlash Utility" bar if you need to install WinFlash Utility. Once you made your selection, a Setup window run the installation automati- cally.

  • Page 53: View The User's Manual

    Insert the attached CD into your CD-ROM drive and the CD AutoRun screen should appear. If the AutoRun screen does not appear, double click on AutoRun icon in My Computer to bring up Shuttle Mainboard Software Setup screen. Select using your pointing device (e.g. mouse) on the “Manual" bar.

  • Page 54: Bios Setup

    5 BIOS SETUP AB60N BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This information is stored in battery-backed RAM so that it retains the Setup information even if the system power is turned off.

  • Page 55: The Main Menu

    5.2 The Main Menu Once you enter the AwardBIOS(tm) CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from sev- eral setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter>...
  • Page 56 PnP / PCI Configurations This entry appears if your system supports PnP / PCI. PC Health Status This entry shows the current system temperature, Voltage, and FAN speed. Frequency/Voltage Control Use this menu to specify your settings for frequency/voltage control. Load Fail-Safe Defaults Use this menu to load the BIOS default values for the minimal/stable per- formance of your system to operate.

  • Page 57: Standard Cmos Features

    Standard CMOS Features The items in Standard CMOS Setup Menu are divided into 10 categories. Each category includes no, one or more than one setup items. Use the arrow keys to highlight the item and then use the <PgUp> or <PgDn> keys to select the value you want in each item.
  • Page 58 IDE Channel 1 Master Options are in its sub-menu. Press <Enter> to enter the sub-menu of detailed options. IDE Channel 1 Slave Options are in its sub menu. Press <Enter> to enter the sub-menu of detailed options. Drive A/Drive B Select the type of floppy disk drive installed in your system.
  • Page 59 ****************************************************** IDE Adapters The IDE adapters control the hard disk drive. Use a separate sub-menu to configure each hard disk drive. IDE HDD Auto-Detection Press <Enter> to auto-detect HDD on this channel. If detection is successful, it fills the remaining fields on this menu. Ø...
  • Page 60 Precomp Warning: Setting a value of 65535 means no hard disk. Ø Min = 0, Max = 65535 Landing zone Set the Landing zone size. Ø Min = 0, Max = 65535 Sector Number of sector per track. Ø Min = 0, Max = 255 ****************************************************** - 56 -...

  • Page 61: Advanced Bios Features

    Advanced BIOS Features This section allows you to configure your system for basic operation. You have the opportunity to select the system's default speed, boot-up sequence, keyboard operation, shadowing, and security. Hard Disk Boot Priority This item allows you to select Hard Disk Boot Device Priority. Bios Write Protect This item allows you to enable or disable the Bios Write Protect.
  • Page 62 Disabled No warning message will appear when anything attempts to access the boot sector or hard disk partition table. Ø The choice: Enabled or Disabled. CPU L1&L2 Cache All processors that can be installed in this mainboard use internal level1(L1) and external 2(L2) cache memory to imporve performance.
  • Page 63 Boot Up Floppy Seek Seeks disk drives during boot-Up. Disabling speed boots up. Ø The choice: Enabled or Disabled. Boot Up NumLock Status Selects power-on state for NumLock. Ø The choice: Off or On. Gate A20 Option This entry allows you to select how the gate A20 is handled. The gate A20 is a device used for above 1MBye of address memory.
  • Page 64 Setup The system will boot, but access to Setup will be denied if the correct password is not entered promptly. Ø The choice: System or Setup. Note: To disabled security, select PASSWORD SETTING at Main Menu, and then you will be asked to enter password. Don't type anything and just press<Enter>;...

  • Page 65: Advanced Chipset Features

    Advanced Chipset Features This section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and access to sys- tem memory resources, such as DRAM and the external cache. It also coor- dinates communications between the conventional ISA bus and the PCI bus.
  • Page 66 Active to Precharge Delay This item select the SDRAM Active to Precharge Delay. (8T, 7T, 6T, or 5T) Ø The Choice: 8, 7, 6, or 5. DRAM RAS# to CAS# Delay This field lets you insert a timing delay between the CAS and RAS strobe signals, and you can use it when DRAM is written to, read from, or refreshed.
  • Page 67 Memory Hole At 15M-16M You can reserve this area of system memory for ISA adapter ROM. When this area is reserved, it cannot be cached. The user information of peripherals that need to use this area of system memory usually discusses their memory requirements.

  • Page 68: Integrated Peripherals

    Integrated Peripherals These options display items that define the operation of peripheral comopnents on the system's input/output ports. On-Chip IDE Device Options are in its sub-menu. Press<Enter> to enter the sub-menu of details options. IDE HDD Block Mode Block mode is also called block transfer, multiple commands, or mul- tiple sector read/write.
  • Page 69 IDE Primary Master/Primary Slave/Secondary Master/ Secondary Slave UDMA Each IDE channel supports a master device and a slave device. This mainboard supports UltraDMA technology, which provides faster access to IDE devices. If you install a device that supports UltraDMA, change the appropriate item on this list to Auto.
  • Page 70 Combined Mode: PATA and SATA are combined. Max. of 2 ATA drives in each channel. (DOS,Win2K,Win98/ME...) should set SATA and PATA to Compatible Mode. Serial ATA 1 (Channel 0) Serial ATA 1 (Channel 0) Slave Master Primary Primary Master Slave Serial ATA 2 (Channel 0) (Channel 0)
  • Page 71 Enhanced Mode: Enable both SATA and PATA. Max. of 6 ATA drives are supported. New OS that support switch to Enhanced mode (WinXP,Windows.NET Server) can set SATA and PATA to Enhanced Mode. Serial ATA 1 (Channel 2) Primary Master or Secondary (Channel 3) Serial ATA 2 (Channel 3)
  • Page 72 Serial ATA Port0/1 Mode This item allows you to set the Serial ATA Port mode. Ø The choice: Primary Master, Primary Slave, Secondary Master, Secondary Slave, SATA0 Master, SATA1 Master. Onboard Device Options are in its sub-menu. Press<Enter> to enter the sub-menu of details options. USB Controller Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have USB peripherals.
  • Page 73 Onboard FDC Controller This item specifices onboard floppy disk drive controller. This setting allows you to connect your floppy disk drives to the onboard floppy connector. Choose the "Disabled" settings if you have a separate control card. Ø The choice: Enabled Disabled. Onboard Serial Port1/Port2 Select an address and corresponding interrupt for the first and second serial ports.

  • Page 74: Power Management Setup

    Power Management Setup The Power Management Setup allows you to configure your system to most effectively saving energy while operating in a manner consistent with your own style of computer use. ACPI Function This item is the Advanced Configuration and Power Management (ACPI), it always Enable and Gray.
  • Page 75 Power Management This category allows you to select the type (or degree) of power saving and is directly related to the following modes: Min Saving Minimum power management. Suspend Mode= 1 hr. HDD Power Down=15min. Max Saving Maximum power management. Suspend Mode=1min.
  • Page 76 Suspend Mode When this item enabled and after the set up time of system inactivity, all devices except the CPU will be shut off. Ø The choice: Disabled, 1 Min, 2 Min, 4 Min, 8 Min, 12 Min, 20 Min, 30 Min, 40 Min, or 1 Hour. HDD Power Down When this item enabled and after the set up time of system inactivity, the hard disk drive will be powered down while all other devices remain...
  • Page 77 Resume by Alarm When this item enabled, you can set the date and time at which the RTC (real-time clock) alarm awakens the system from Suspend mode. Ø The choice: Disabled or Enabled. Data (of Month) Alarm This item selects the alarm date. Ø...
  • Page 78 KB Power ON Password This item allows you to set the KB Power ON Password. Ø The choice: Enter. Hot Key Power ON Power-on by soft-on/off button and keyboard are available. Ø The choice: Any Key, Ctrl-F1~Ctrl-F12. PS2 Mouse Power ON This item allows you to set the PS2 Mouse Power ON function..

  • Page 79: Pnp/Pci Configuration

    PnP/PCI Configurations This section describes the configuration of PCI bus system. PCI or Personal Computer Interconnection is a system which allows I/O devices to operate at the speed CPU itself keeps when CPU communicat- ing with its own special components. This section covers some very tech- nical items, and it is strongly recommended that only experienced users should make any changes to the default settings.
  • Page 80 IRQ Resources When resources are controlled manually, assign each system interrupt a type, depending on the type of device using the interrupt. IRQ3/4/5/7/9/10/11/12/14/15 assigned This item allows you to determine the IRQ assigned to the ISA bus and is not available to any PCI slot. Legacy ISA for devices is compliant with the original PC AT bus specification;...

  • Page 81: Pc Health Status

    PC Health Status Shutdown Temperature Enables you to set the maximum temperature the system can reach be- fore powering down. Ø The choice: 60 C/140 F, 65 C/149 F, 70 C/158 F or 75 C/167 System Component Characteristics These fields provide you with information about the systems current operating status.

  • Page 82: Frequency/Voltage Control

    Frequency/Voltage Control CPU Clock Ratio This item allows you to adjust CPU Ratio. If your CPU ratio is unlocked, the item is visible. Min: 8 Max: 50 Ø Key in a DEC number: (Between Min and Max.) Auto Detect PCI Clk This item allows you to enable/disable auto disable empty PCI Slot Clock.

  • Page 83: Load Fail-Safe Defaults

    Async AGP/PCI/S-ATA CLK This item allows you to set AGP/PCI clock and CPU clock asynchro- nous. You can select 66/33, 73/36, or 80/40 to fixed AGP/PCI clock even if you adjust CPU clock. Ø The choice: Sync by CPU Clock, fixed 66/33/100 MHz, fixed 73/36/ 100 MHz, fixed 80/40/100.

  • Page 84: Set Supervisor/ User Password

    Supervisor/User Password Setting You can set either supervisor or user password, or both of them. The differences between them are: Supervisor Password and User Password The options on the Password screen menu make it possible to restrict access to the Setup program by enabling you to set passwords for two different access modes: Supervisor mode and User mode.

  • Page 85: Save & Exit Setup

    Password Disable If you select System at Security Option of BIOS Features Setup Menu, you will be prompted in entering the password whenever the system is rebooted or you try to enter Setup. If you select Setup at Security Option of BIOS Features Setup Menu, you will be prompted only when you try to enter Setup.

Table of Contents