Indiana Furniture Blade One 10 Assembly Instructions Manual
4 piece conference table
Hide thumbs
Also See for Blade One 10:
- Assembly instructions manual (7 pages) ,
- Assembly instructions manual (8 pages)
Advertisement
Quick Links
Parts List:
Qty (3) Short Tops
Qty (8) Jointer Plates
Qty (4) Small Angle Brackets
Hardware Included
(5) Bags of #10 x 7/8 " Flat Head Screws
(2) Bag of #6 x ½" Pan Head Screws
(1) Bag of ¼"-20 x 2" Bolt and ¼"-20 Nuts
(32) ¼"-20 x 1-3/4" Button Head Bolt, ¼"-20
Nuts and ¼" Star Washers
(16) #8 x 5/8" Pan Head Screws
Velcro (For Metal Base Covers)
2298-1104P144192k
Blade One 10: 4 Piece Conference Table Assembly Instructions 144" to 192" Lengths
Qty (4) Long Tops
Qty (16) Jointer Bolts
Short L-Brackets
Qty (4) Large L-Brackets
Qty (2) Trough Assembly
Long L-Brackets
Tools Required
(2) People
Drill with phillips screw bit
5"
32 Allen Wrench
5mm Allen Wrench
7/16" Wrench
Level
Qty (4) U- Jointer Plates
Qty (2) Bases
Qty (1) Mid-Base
1
Advertisement
Related Manuals for Indiana Furniture Blade One 10
Summary of Contents for Indiana Furniture Blade One 10
- Page 1 Blade One 10: 4 Piece Conference Table Assembly Instructions 144” to 192” Lengths Parts List: Qty (3) Short Tops Qty (4) Long Tops Qty (4) U- Jointer Plates Qty (2) Trough Assembly Qty (8) Jointer Plates Qty (16) Jointer Bolts...
- Page 2 Step 1: Remove the accent cover off of the bases by pulling it off. Next, Using the supplied Velcro with Self-Stick Adhesive on it, Place the Velcro on the outside of the base and on the inside of the accent cover along the length of the vertical edge Base with Accent Cover Removed Base with Accent Cover Attach Velcro here...
- Page 3 Step 2: Bolt together the (2) Bases to the Trough assembly using the ¼”-20 x 2” Bolts , ¼” -20 x 1-3/4” Bolts, ¼”-20 Nuts, Large L-Brackets, Small Angle Brackets, and #8 x 5/8” Pan Head Screws Fasten Vertical Edge of Large L- Fasten Small angle Brackets with Bracket with ¼”-20x 2”...
- Page 4 Step 4: Bolt together the remaining trough section to the Mid base along with the remaining Base. Also, install the Short L-Brackets and the Long L-Brackets to the trough section using the #6 x ½” Pan Head Screws Short L-Brackets Long L-Brackets Step 5: Next fasten the U-Jointer Plates to the short tops using the #10 X 7/8”...
- Page 5 Step 6: Using the supplied Jointer Bolts and a 7/16” Wrench, fasten the tops together as shown (Note: Do not attach the tops to the L-Brackets at this time!) Jointer Bolt Step 7: Now slide the tops so the U-Jointer Plate screw holes can be accessed and fasted the plate with the #10X7/8” Screws Fasten U-Jointer Plate...
- Page 6 Step 8: Attatch the middle short top to the tops in Step 7. Next, similart to Step 6 attache the remaining tops with the provided Jointer Bolts. Now Slide the tops so the U-Jointer plate can be attached using the #10 X 7/8” screws. Middle Short Top Fasten the U-jointer plate...
- Page 7 Step 9: Fasten the U-Jointer plates to the Middle Top by using the clearance holes in the trough Use access holes to fasten U-Jointer Plate Step 10: Next, attach the remaining jointer plates to the tops and level the tops using the fine-tune adjustments Fine Tune Adjustments...
- Page 8 Step 11: Next, Fasten the tops down to the L-Brackets using the #6x 1/2” screws Attach Tops to the L-Brackets Step 12: Level the table using the 5mm Allen Wrench. Next (If Applicable) install all power ports and route wires down the base.
- Page 9 Step 13: When the Table is completely wired, install the Base Covers. Once the base covers are installed, using the Silver #6 x ½” screws, fasten the covers to the underside of the trough. You are Finished!