Indiana Furniture Blade One 10 Assembly Instructions Manual
4 piece conference table 96” to 120” lengths
Hide thumbs
Also See for Blade One 10:
- Assembly instructions manual (8 pages) ,
- Assembly instructions manual (9 pages)
Advertisement
Quick Links
Parts List:
Qty (2) Short Tops
Qty (4) Jointer Plates
Qty (4) Small Angle Brackets
Hardware Included
(3) Bags of #10 x 7/8 " Flat Head Screws
(1) Bag of #6 x ½" Pan Head Screws
(1) Bag of ¼"-20 x 2" Bolt and ¼"-20 Nuts
(8) ¼"-20 x 1-3/4" Button Head Bolt, ¼"-20
Nuts and ¼" Star Washers
(16) #8 x 5/8" Pan Head Screws
(1) 29mm Silver Polycom Grommet
Velcro (For Metal Base Covers)
Blade One 10: 4 Piece Conference Table Assembly Instructions 96" to 120" Lengths
Qty (2) Long Tops
Qty (8) Jointer Bolts
Qty (2) Large L-Brackets
(Optional)
Qty (1) Trough Assembly
Qty (4) Short L-Brackets
Tools Required
(2) People
Drill with phillips screw bit
5"
32 Allen Wrench
5mm Allen Wrench
7/16" Wrench
Level
Qty (2) U- Jointer Plates
Qty (2) Long L-Brackets
Qty (2) Bases
2298-1104P96120K
1
Advertisement
Related Manuals for Indiana Furniture Blade One 10
Summary of Contents for Indiana Furniture Blade One 10
- Page 1 Blade One 10: 4 Piece Conference Table Assembly Instructions 96” to 120” Lengths Parts List: Qty (2) Short Tops Qty (2) Long Tops Qty (1) Trough Assembly Qty (2) U- Jointer Plates Qty (8) Jointer Bolts Qty (4) Jointer Plates...
- Page 2 Step 1: Remove the accent cover off of the bases by pulling it off. Next, Using the supplied Velcro with Self-Stick Adhesive on it, Place the Velcro on the outside of the base and on the inside of the accent cover along the length of the vertical edge Base with Accent Cover Removed Base with Accent Cover Attach Velcro here...
- Page 3 Step 2: Bolt together the (2) Bases to the Trough assembly using the ¼”-20 x 2” Bolts , ¼” -20 x 1-3/4” Bolts, ¼”-20 Nuts, Large L-Brackets, Small Angle Brackets, and #8 x 5/8” Pan Head Screws Fasten Vertical Edge of Large L- Fasten Small angle Brackets with Bracket with ¼”-20x 2”...
- Page 4 Step 4: Next, fasted the U-Jointer Plate to the short tops using the #10 x 7/8” Flat Head Screws. Step 5: Using the supplied Jointer Bolts and a 7/16” Wrench, fasten the tops together (Note: Do Not Attach the Tops to the L-Brackets at this time!) Jointer Bolts...
- Page 5 Step 6: Fasten the (4) Jointer Plates to the tops using the provide #10 X 7/8” screws. Attach (4) Jointer Plates Step 7: Next slide the assembled tops to the side so the U-Jointer Plate can be fastened. Repeat for the opposite side. Attach U-Jointer Plate to the Long tops Slide the Top Assembly to access...
- Page 6 Step 8: Now, center the top assembly on the trough assembly and if necessary, use the fine-tune adjustment screws to level the work surfaces using the 5/32” Allen wrench. Next, fasten the top assembly to the L-Brackets with the provided #8 X 5/8” Pan Head Screws. Fine Tune Adjustment Set Screws Fine-Tune adjust the work surfaces, then screw down to the...
- Page 7 Step 9: Level the table using the 5mm Allen Wrench. Next (If Applicable) install all power ports and route wires down the base. Levelers Are Here Step 9: When the Table is completely wired, install the Base Covers. Once the base covers are installed, using the Silver #6 x ½” screws, fasten the covers to the underside of the trough.