Billion BiGuard S100N Quick Start Manual

6
CONFIGURING IPSEC
E. F.
Configuring IPSec
Click Add to add the account. Click Apply to confirm the settings
and you will be directed to the This section describes how to set up an BiGuard S100N IPSec connection using the
Once the account is added, the
newly added account will be Account Table page displaying all the IPSec Wizard. Refer to the following to configure an IPSec connection:
displayed in the Account Table created accounts.
below (Note: Account Table A.
Click Quick Start
displays all the accounts under the
Menu bar. The IPSec Wizard screen
chosen Group)
appears.
B.
Type a connection name in the
5
Connection Name field.
CONFIGURING WIRELESS
C.
Configuring Wireless
Enter a preshared key in the
Preshared Key field. The preshared
This section describes how to configure the BiGuard S100N with basic settings so that
users can use wireless connection to connect to the router. Before a user can access key is used by the Internet Key
through wireless, the WLAN service must be enabled. Exchange protocol (IKE) to establish a shared security policy and authenticated
keys. Each router must be able to identify its counterpart using the preshared key
A.
Click Quick Start → Wireless in
before any IPSec traffic can be passed.
the Menu bar. The IPSec Wizard
D.
screen appears.
Select a connection type from the
Connection Type buttons and click
B.
Select Enable to enable the
Next.
WLAN service.
C.
Type an unique ESSID to identify
LAN to LAN
the router to wireless clients. A.
LAN to LAN uses an IPSec VPN tunnel to securely establish a connection to a remote
D. router.
Select whether or not to Enable
G.
(hide ESSID) or Disable (show Select the Security Mode: Disable, A.
Selecting LAN to LAN and clicking
ESSID).
WPA Pre-Shared Key, WEP and
Next displays the Remote
WPA2 Pre-Shared Key to enhance
E.
Information screen.
Depending on where you are in security to the wireless connection.
the world, please select the B.
H.
Type the IP address or Hostname of
Regulation Domain which shows Click Apply to confirm the settings
the remote VPN gateway in the
your location. Difference in and your wireless service will be open
Remote Secure Gateway Address
Regulation Domain which give a for users to connect.
(or Hostname) field.
different option for Channel ID.
C.
F.
Type the IP Address and Netmask of
Select the Channel ID. Different
the Remote Network in the supplied
Channel ID communicates on
fields.
different frequency and certain
frequency might have less D.
Click Back to return to the
interference which can let user
Connection Information screen or
gain better quality connection.
click Next to proceed to the
Configuration Summary screen.
7
LAN to LAN (Mobile LAN)
LAN to LAN (Mobile LAN) uses an IPSec VPN tunnel to securely establish a connection to
a remote router that is using Dynamic Internet IP.
A.
→
IPSec in the Selecting LAN to LAN (Mobile
LAN) and clicking Next displays
the Remote Information screen:
B.
Type the remote identifier of the
remote gateway in the Remote
Identifier field. Depending on the
input value, the ID type is
A.
auto-defined as IP Address,
FQDN(DNS) or FQUN(E-mail).
C.
Click Back to return to the
Connection Information screen or
click Next to proceed to the
E.
The following steps depend on the
Configuration Summary screen.
choice of connection made.
LAN to Host
LAN to Host uses an IPSec VPN tunnel to securely establish a connection to a computer.
A.
Selecting LAN to Host and clicking
Next displays the Remote
Informa-tion screen:
B.
Type the IP address or hostname of
the remote VPN device in the
Remote Secure Gateway Address
A.
(or Hostname) field to allow a VPN
tunnel to be established.
C.
Click Back to return to the
Connection Information screen or
click Next to proceed to the
Configuration Summary screen.
B.
8
LAN to Host (Mobile Client)
LAN to Host (Mobile Client) uses an IPSec VPN tunnel to securely establish a connection
to a computer that uses Dynamic Internet IP.
A.
Selecting LAN to Host (Mobile
Client) and clicking Next displays
the Remote Information screen:
B.
Type the remote identifier of the
remote gateway in the Remote
Identifier field. Depending on
A.
the input value, the ID type is
autodefined as IP Address,
FQDN(DNS) or FQUN(E-mail).
C.
Click Back to return to the
Connection Information screen or
click Next to proceed to the
Configuration Summary screen.
B.
LAN to Host (for BiGuard VPN Client)
LAN to Host (for BiGuard VPN Client) uses an IPSec VPN tunnel to securely establish
a connection to a computer that has BiGuard VPN Client installed.
A.
Selecting LAN to Host (for
BiGuard VPN Client) and clicking
Next displays the Remote
Information screen:
B.
Type the VPN Client IP Address for
the BiGuard VPN Client. This value
is applied on both remote ID and
A.
Remote Network as a single
address. (Note: Ensure that each
client uses a different VPN Client
Address).
C.
Click Back to return to the
Connection Information screen or
B.
click Next to proceed to the
Configuration Summary screen.
9 10
The IPSec Configuration Summary screen
The Configuration Summary screen displays the data input on the selected Connection
Type screens.
A.
Review the connection information
on the screen. To make any
necessary amendments, click Back
to return to the Connection Type
screen. To complete the IPSec
Configuration, click Done.
A.
B.
A.
A.
Support Billion Product Registration
For additional information, please Billion is committed to before and after sales customer services.
refer to the User's Guide in the You will get the most out of your Billion's products after registration.
software CD. For technical support, Please register online at http://www.biguard.com/register/ to receive
C Billion Electric Co., Ltd.
B. please email to support@billion.com. valuable services and support from us.
BiGuard S100N v 1.00
11
S100
802.11n SSL/IPSec VPN Security Gateway