Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Viavito PT1000 GT VKR
Summary of Contents for Viavito PT1000 GT VKR
- Page 1 Owner’s Manual. PT1000 GT VKR Power Tower www.viavito.com Manual version 1.1...
-
Page 2: Table Of Contents
Customer Support 22/23 out of your new piece of equipment. Contact Information For more information, or if you require Manufacturer’s Warranty any assistance please email us at support@viavito.com Technical Information 24/26 Safety Standards: Exploded Diagram Parts List The weight bench conforms... -
Page 3: Safety Information
• The specifications of this product may any issues have been resolved. Use only vary slightly from the illustrations and spare parts supplied by Viavito. are subject to change without notice. 07 Always wear appropriate workout This exercise machine is built for optimum clothing when exercising. - Page 4 16 WARNING! Inappropriate use of this this product. machine such as while under the influence of drugs or alcohol, not in line Viavito assumes no responsibility for the with instructions or excessive usage, personal injury and/or property damage may result in serious injury or death.
- Page 5 Warning Decal Placement 120 kg www.viavito.com...
-
Page 6: Assembly
Assembly Product Overview Thank you for selecting the Viavito PT1000 GT VKR power tower. This manual will guide you through the assembly process. ASSEMBLED DIMENSIONS: Height: 84 in. Width: 41 in. Pull-up Arm Depth: 44 in. Upright Arm Pad Backrest... -
Page 7: Part Identification Chart
M10 x 90mm Bolt (19) M10 x 75mm Screw (31) M8 Washer (15) M10 x 50mm Screw (29) M8 x 80mm Screw (21) M10 Nylon Locknut (25) M10 x 20mm Screw (20) M10 Washer (30) M8 x 70mm Screw (24) www.viavito.com... -
Page 8: Before You Begin
- 1 Phillips screwdriver Assembly will be more convenient if you have a socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches. Important: Some of the parts described in the assembly steps may be pre-assembled. www.viavito.com... -
Page 9: Assembly Instructions
Base Frame (1) with two M10 the Center Base (4). x 90mm Bolts (19), two M10 Washers (30) and two M10 Nylon Locknuts (25). Make sure the warning decal is in the position shown. Do not tighten the Locknuts yet. Decal www.viavito.com... - Page 10 Step Two. 01 Attach the Upright Base (2) to a Center Base (4) with two M10 x 95mm Bolts (27) and two M10 Nylon Locknuts (25). Do not fully tighten the Locknuts yet. www.viavito.com...
- Page 11 Base (2). Attach the Upright and (27) and two M10 Nylon Locknuts (25). Support (5) to the Upright Base with Do not fully tighten the Locknuts yet. four M10 x 20mm Screws (20). 03 Tighten the M10 Nylon Locknuts (25) used in steps 1-3. www.viavito.com...
- Page 12 Arm (7) with an M10 x 50mm Screw the thick side of the Cap is on the side (29), an M10 x 75mm Screw (31) and shown. two M10 Washers (30). 03 Attach the Right Handle (8) in the same manner. Thick Side Thick Side www.viavito.com...
- Page 13 Step Five. 01 Insert the Pull-up Arm (7) into the Upright (3). Attach the Pull-up Arm to the Upright with four M10 x 20mm Screws (20) and four M10 Washers (30). www.viavito.com...
- Page 14 Dip Arm (6) to the Upright (3) with the the Dip Arm (6) and into the Upright. Bolt and an M10 Nylon Locknut (25). Do not overtighten the Locknut; the Dip Arm must be able to pivot easily. Grease Tether Hole www.viavito.com...
- Page 15 02 Wet a Short Foam Grip (16) and the indicated handle on the Dip Arm (6) with soapy water. Press a Bushing (18), the Short Foam Grip and a 28mm Round Inner Cap (14) onto the handle on the Dip Arm (6). Handle www.viavito.com...
- Page 16 Step Eight. 01 Attach the Backrest (11) to the Upright 02 Make sure that all parts have been (3) with 8 two M8 x 70mm Screws (24) properly tightened before the power and two M8 Washers (15). tower is used. www.viavito.com...
-
Page 17: Adjustments
Pin must be inserted into the Dip Arm and Upright (3) when the Dip Arm is in the up position, as shown in the drawing. The Pin will be behind the Upright when the Dip Arm is in the down position. www.viavito.com... -
Page 18: Conditioning Guidelines
• Control appetite injuries, joint problems, obesity and • Boost self-image asthma. • Improve muscle tone and strength • Improve flexibility • Lower blood pressure • Relieve insomnia www.viavito.com... -
Page 19: Beginner's Guide To Exercise
• Start slowly and build up your time, speed and resistance gradually; doing too much too soon can lead to injuries. • If you are sore or tired, give yourself a few extra days to recover. www.viavito.com... -
Page 20: Stretching Guide
• Stretch at least three times a week to perature, which greatly reduces the risk of maintain flexibility. injury. Stretching develops flexibility and reduces muscles soreness. Stretches should be held for 15 to 30 seconds. www.viavito.com... - Page 21 The purpose of cooling down is to return the body to its normal or near normal, resting state at the end of each exercise session. A proper cool-down slowly lowers your heart rate, allows blood to return to the heart and helps prevent muscle soreness caused by the build-up of lactic acid in the muscles. www.viavito.com...
-
Page 22: Customer Support
• Precise description of the issue or defect. IMPORTANT! Please retain your sales receipt. Viavito Customer Care may request proof of purchase to validate eligibility for warranty service. Warranty cover starts from the date shown on the proof of purchase. -
Page 23: Manufacturer's Warranty
Manufacturer's Warranty Viavito warrants this product to be free Viavito is not responsible or liable for of defects of material and workmanship, direct, indirect, or consequential losses under normal use and conditions, for a arising out of or in connection with the use... -
Page 24: Technical Information
Technical Information Exploded Diagram 18 14 www.viavito.com... -
Page 25: Parts List
M8 x 80mm Screw M10 x 200mm Bolt M8 x 70mm Screw M10 Nylon Locknut 50mm x 127mm Inner Cap M10 x 95mm Bolt 70mm x 50mm Outer Endcap M10 x 50mm Screw M10 Washer M10 x 75mm Screw www.viavito.com... -
Page 26: Space Required
Annex 1: Space Required For safety reasons, minimum clearance for the equipment is 0.6m in all directions. 1140 www.viavito.com... - Page 27 www.viavito.com...