Residual Risks; Technical Data - Scheppach SC2200PE Translation Of Original Instruction Manual

Service
Before cleaning, repair, inspecting, or adjusting, shut
off the engine and make certain that all moving parts
have stopped. Disconnect the spark plug wire, and
keep the wire away from the plug to prevent acci-
dental starting.
Have your machine serviced by qualified repair per-
sonnel using only identical replacement parts. This
will ensure the safety of the machine maintained.
Thoroughly inspect the area to be worked, keep the
working area clean and free of debris to prevent trip-
ping. Operate on a flat level ground.
Never place any part of your body where it would be
in danger if movement should occur during assem-
bly, installation, and operation, maintenance, repair-
ing or moving.
Keep all bystanders, children, and pets at least 23m
(75 feet) away. If you are approached, stop the unit
immediately.
Start the engine carefully according to instructions
and with feet well away from the moving parts.
Never leave the operating position when the engine
is running.
Always hold the unit with both hands when operat-
ing. Keep a firm grip on the handlebars. Be aware
that the machine may unexpectedly bounce upward
or jump forward if the machine should strike buried
obstacles such as large stones.
Walk, never run with the machine.
Use extreme caution when in reverse or pulling the
machine towards you.
Exercise extreme caution when operating on or
crossing gravel drives, walks, or roads. Stay alert
for hidden hazards or traffic.
Pay the utmost attention when working on frozen
ground as the machine may tend to skid.
Do not operate the machine in confined areas where
there may be a risk of crushing the operator between
the machine and another object.
Never operate the machine on slopes where angle
is over 20°.
Move the machine at least 3m away from the refue-
ling point before starting engine.
Always check the oil level of the engine before use.
Do not operate the machine on a bumpy or steep
road. Exercise caution to avoid slipping or falling,
especially when operation in reverse.
Inspect that all nuts, bolts and brush rollers are tight
and well connected to ensure the safety and reliabil-
ity of this machine prior to any operation.
Adjust the lever cables to ensure that they are flex-
ible and reliable.
Adjust the brush to proper height prior to any oper-
ation.
Inspect the air pressure in the tires prior to use and
pay attention to sharp objects when using the ma-
chine to prevent the tires from being pierced.
24 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Since some parts of the machine are made of plas-
tic or rubber materials, it should be kept away from
any chemical article to prevent a chemical reaction
from occurring.
When Sweeping, if the brush is blocked by some soft
materials. Please stop engine and remove the spark
plug wire then remove the materials.

6. Residual risks

Risk of injury!
Compliance with all relevant building codes dangers
can occur when operating the machine, eg by flying
away from workpiece parts flying off tool parts for
damaged tools, flying off whirled stone and dirt parts,
noise and dust emission.
Residual mechanical hazards
Hazards caused by vibration
Prolonged work with the machine can cause vibra-
tion to physical impairments. Take regularbreaks.

7. Technical data

Transmission
Forward Speed
Reverse Speed
Total machine width
Sweeping width
Broom Ø
Broom speed
Level of vibration on
handlebar
Weight
Drive:
Engine Type
Capacity
load speed
Maximum Speed
Recoil starter (pull starter) /
Motor Starters
Power
Unleaded gasoline octane
Fuel number from 90 to a maxi-
mum ethanol content of 5%
Maximum fuel tank
capacity
Required motor oil
Oil tank capacity
maximum
Subject to techcnical modifications!
3 Forward + 1 Reverse
2,5 - 4,3 km/h
2,5 km/h
1060 mm
1000 mm
350 mm
180 - 350 min
-1
r: 7,127 / l: 5,577 m/s²
82 kg
4-stroke engine
173 ccm³
2800 1/min.
2900 1/min.
E - Start
3,6 kW / 4,9 HP
1 l
SAE 10W-30 / 10W-40
0,6 l