Installation; Unit Location - Recommendations - Panasonic PAW-FC Installation And Maintenance Manual

PAW-
EC fan 2-pipe
1)
Lo / Med / Hi
Total cooling capacity
1)
Lo / Med / Hi
Sensible cooling capacity
Water flow Lo / Med / Hi
Water pressure drop Lo / Med / Hi
2)
Lo / Med / Hi
Heating capacity
PAW-
EC fan 4-pipe
1)
Lo / Med / Hi
Total cooling capacity
1)
Lo / Med / Hi
Sensible cooling capacity
Water flow Lo / Med / Hi
Water pressure drop Lo / Med / Hi
2)
Lo / Med / Hi
Heating capacity
Water flow Lo / Med / Hi
Water pressure drop Lo / Med / Hi
1) According to Eurovent standard. Air: 27°C DB / 19°C WB. Water in/out: 7°C / 12°C.
2) According to Eurovent standard. Air: 20°C. Water in/out: 45°C / 40°C.

5. Installation

CAUTION
- The unit installation work must be done by qualified personnel according to the local rules and this manual.
- The unit should not be installed in a bathroom, a laundry, a sauna or a swimming-pool.
During the installation:
Take care to avoid any rough handling or impacts when
•
unloading and moving the appliance.
Before hoisting into position, test lift to insure stability and
•
balance. Avoid twisting or uneven lifting of the units.
The units shall be carefully inspected before unit
•
installation to make sure that no handling damage has
occurred.
5.1 Unit location – Recommendations
Select the unit location with the following aspects in mind:
Choose an area free from obstructions which may cause
•
uneven air distribution and/or return.
Consider using an area where installation is easy.
•
Choose a position that allows for the clearances required.
•
Look for a position in the room which ensures the best
•
possible air distribution.
Install unit in a position where condensate can easily be
•
piped to an appropriate drain.
FC2E-U020 FC2E-U030
kW 1,6 / 1,8 / 2,4 1,9 / 2,9 / 4,0
kW 1,3 / 1,5 / 2,0 1,4 / 2,2 / 3,1
l/h 267 / 306 / 409 325 / 497 / 688
kPa 4,2 / 6,9 / 11,2 3,5 / 8,6 / 14,6
kW 2,2 / 2,5 / 3,2 2,3 / 3,7 / 4,5
FC4E-U020 FC4E-U030
kW 1,4 / 1,5 / 2,0 2,0 / 2,7 / 3,4
kW 1,2 / 1,4 / 1,9 1,5 / 2,1 / 2,6
l/h 234 / 262 / 344 344 / 464 / 581
kPa 6,6 / 9,1 / 14,0 4,4 / 8,2 / 11,7
kW 0,8 / 0,9 / 1,2 2,2 / 3,1 / 3,8
l/h 132 / 153 / 201 374 / 530 / 658
kPa 25,7 / 33,4 / 53,6 13,7 / 24,2 / 35,0
FC2E-U040 FC2E-U050
2,8 / 3,5 / 4,7 3,4 / 4,4 / 6,1
2,1 / 2,7 / 3,6 2,6 / 3,5 / 4,7
481 / 604 / 808 579 / 765 / 1050
6,8 / 11,4 / 18,6 8,4 / 13,1 / 22,2
3,7 / 4,6 / 6,2 4,5 / 6,0 / 8,1
FC4E-U040
2,6 / 3,2 / 4,0
2,1 / 2,6 / 3,3
442 / 556 / 690
6,7 / 10,9 / 15,5
3,0 / 3,5 / 4,1
521 / 603 / 699
24,2 / 30,9 / 39,8
All these sections have been inspected before leaving the
•
factory. It is therefore important to insure that no bolts,
screws or other fixing system are loosened or missing
before the commissioning. During the handling of the
machine it is mandatory to provide all the devices
necessary to guarantee personal safety.
Positions to avoid:
• Exposure to direct sunlight.
Exposure to oil vapours.
•
• Areas close to heat sources.
Installation in areas with high frequency waves.
•
• On damp walls or in positions that may be exposed to
water hazard.
Where curtains or furniture may obstruct free air circulation.
•
• Positions too close to heating sources which may damage
the unit.
10
FC2E-U060 FC2E-U070
3,7 / 5,5 / 7,2 4,1 / 6,5 / 9,6
2,7 / 4,1 / 5,4 3,0 / 4,9 / 7,2
640 / 944 / 1243 700 / 1119 / 1649
3,4 / 7,6 / 11,7 5,8 / 13,1 / 24,6
4,5 / 7,4 / 10,0 5,2 / 9,2 / 13,0
- FC4E-U060 FC4E-U070
- 3,0 / 5,0 / 6,6 3,2 / 6,1 / 7,9
- 2,3 / 3,8 / 5,1 2,6 / 4,7 / 6,3
- 516 / 858 / 1144 549 / 1041 / 1366
- 6,0 / 14,1 / 22,4 7,2 / 19,2 / 30,1
- 3,7 / 5,5 / 7,0 4,5 / 7,1 / 9,8
- 636 / 939 / 1210 776 / 1214 / 1686
- 7,6 / 13,8 / 20,7 10,2 / 20,8 / 36