Page 1
Aroot Co., Ltd. 28-6, Gajangsaneopdong-ro, Osan-si, Gyeonggi-do ,18103, Republic of Korea TEL +82-31-8077-5000 / FAX +82-31-624-5310 / http://www.miniprinter.com B24 ENG Rev. G 01/2021...
Page 2
LABEL PRINTER MODEL : LK-B24 4" Thermal Transfer and Direct Thermal Label Printer All specifi cations are subject to change without notice...
Page 3
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions. 1) This device may not cause harmful interference, and including 2) T his device must accept any interference received, interference that may cause undesired operation. Vic Barczyk 20280 S.
Table of Contents Safety Precautions 1. Unpacking 2. Inspecting The Printer 3. Attaching Power Supply 4. Hooking up the printer and computer 5. Loading the Paper 6. Loading Ribbon 7. T he treatment when you run short of paper and encounter cutter jam proble 8.
Safety Precautions For better safety and reliability, adhere to the following precautionary measures. Read and follow the instructions carefully before operation of the product. Indication Prohibition Must follow Unplug the power from the Do not disassemble outlet Grounding to prevent Do not handle the product with electric shock wet hands...
Page 6
WARNING Failure to follow these instructions could result in fire, electric shock, other injuries, or property damage. Do not disassemble, repair or modify the Do not unplug the product. power cable to turn off the product. Potential risk of malfunction, electric Turn off the power shock, or fire.
2. Inspecting The Printer Interface Power Printer Paper width Guide Printer Head Black Mark Sensor Gap Sensor Button Power Switch Upper Cover Knob...
Page 9
Open the upper cover by pushing the CAUTION knob in the direction of the arrow Make sure to be careful of the HOT head after using long time. " If the cover is not shut down completely, the printer may not work properly Please make sure you hear the closing sound of the upper cover.
3. Attaching Power Supply Power Connectors Please check the specification of the Turn off the power of the printer and AC power cord if it is correct with your connect the power supply to the printer power system. as shown above. Connect the AC power cord to the Insert a plug into the Telectrical outlet.
5. Loading the Paper Turn off the printer and open the Please open the upper cover as shown upper cover by pushing the knob in the above. direction of the arrow Please open as shown above. Insert the paper roll into the printer.
Page 13
- Change paper core size adjusting push button of Label Paper Guide. - 1 inch - - 1.5 inch - Adjust the paper width guide to meet the paper width. Close the upper cover completely and make sure you hear the closing sound. - Please cut the paper in upper direction.
6. Loading Ribbon Direction of Ribbon Loading Make sure that install adjusting the groove. - Paper Core - - Ribbon - Install the ribbon to the right side first Prepare a ribbon and paper core Install the ribbon adjusting the groove after lifting following picture. Release the ribbon forward enough.
Page 15
New ribbon has sticker in the end, so that Install a paper core adjusting the groove, tape is not necessary. In case that ribbon otherwise a paper core can be fallen. doesn’t have sticker, please use tape. Make sure that install a paper core adjusting the groove.
7. T he treatment when you run short of paper and encounter cutter jam proble While you are printing with continuous media, please press PULL lever to the direction of the arrow. " Installation of the new paper " Remove of the paper seized by paper jam " when the printer is short of it "...
9. Self-Test NOTE - Power switch sig ON : Press once. OFF : During 2~3 seconds. Regardless of the power status (Power ON or Power OFF), press and hold the Power button and the Feed button for 2~3 seconds at the same time to print the printer information.
The printer will be stopped after a graph is printed. Then, you can use the printer. If the calibration result is abnormal, set it up in "SEWOO Label Printer Configuration Tool" and then try again. This utility is on the CD and can be...
12. Printer cleaning If the interior of the printer is dusty, printing quality can lowered. In such a case, follow the instructions below to clean up the printer. NOTE 01 Make sure to turn the printer power off prior to cleaning. 02 Regarding printhead cleaning, as the printhead gets very hot during printing, turn off the printer power and wait approximately 10 minutes before cleaning.
13. Connector Interface Connectors USB “ B “ TYPE Ethernet 8 Pin Serial...
Page 23
Ethernet Interface Signal Data Out + Output Data + Data Out - Output Data - Ground Data IN + Input Data + Data IN - Input Data - USB Interface Signal Description DATA- Printer transmit data line DATA+ Printer transmit data line System Ground DIN 8Pin Serial Interface Signal...
14. Standard roll media specification Core Diameter(A) 25.4 or 38.1 mm Max. width 114 mm Roll Max.diameter(B) 127 mm Max.media width(C) 114 mm Min.media width(C) 18 mm Max.media thickness 0.20 mm Min.mdeia thickness 0.06 mm NOTE 01 If the label thickness is more than 0.18mm, adjust the printing speed to 127mm/s. 02 When the paper width is less than 25.4 (1inch), please print 101.6 mm/s When the paper width is between 25.4 (1inch) to 76.2 (3inch), please print 127mm/s.
15. Standard label specification <-- a --> Media width (inch, liner) Maximum 114 mm Minimum 18 mm <-- b --> Label length Minimum 10 mm <-- c --> Label gap height Maximum 10 mm Minimum 2 mm Liner Opacity 50~75%...
16. Label specification with Through-hole <-- a --> Tag or strip width Maximum 114 mm Minimum 18 mm <-- b --> Tag length Minimum 10 mm <-- c --> Detection slot width Minimum 14 mm <-- d --> Detection slot height Maximum 10 mm Minimum...
17. Label with Black Mark <-- a --> Tag or strip width Maximum 114 mm Minimum 18 mm <-- b --> Tag length Minimum 10 mm <-- c --> Black mark width Minimum 14 mm <-- d --> Black mark height Maximum 10 mm Minimum...
18. Continuous stock specification The printer can use continuous paper without any detection gap or black marks. Continuous paper cannot be used in the Test (Dump) Mode. <-- a --> Maximum 114 mm Minimum 18 mm...
19. Specifications Print method Direct Thermal Print speed (Max.) 127mm/sec Print width (Max.) 104mm (4 inch) Print length (Max.) 1,000mm Resolution 203dpi (8 dots/mm) Paper width (Min.~Max.) Min. 18 ~ Max. 114 mm Paper roll size (Min.~Max.) Ø 25.4 mm ~ Ø 127 mm Paper thickness 0.06 ~ 0.20 mm Paper type...
Page 30
Operation 0 ~ 40℃ Temperature Storage -20 ~ 60℃ Operation 10 ~ 90% Humidity Storage 10 ~ 90% Electrical Characteristics 1 Input Voltage DC 24V ± 10% 2 Current Consumption - Operating: Approx. 2.9 A (at ASC∥ printing) - Peak : Approx. 10 A (at print duty 100%, For 10 seconds or less) - Stand-by : Approx.
20. Command List ZPL Command List Command Description Scalable/Bitmapped Font Code 11 BarCode Interleaved 2 of 5 BarCode Code 39 BarCode Code 49 BarCode Planet Code BarCode PDF417 BarCode EAN-8 BarCode UPC-E BarCode Code 93 BarCode Code 128 BarCode(Subsets A, B, and C) UPS MaxiCode BarCode EAN-13 BarCode Micro-PDF417 BarCode...
Page 32
Download Graphics Field Block Field Clock(for Real-Time Clock) Field Data Field Hexadecimal Indicator Field Number Field Origin Field Parameter Field Reverse Print Field Separator Field Typeset Field Variable Field Orientation Comment Graphic Box Graphic Circle Graphic Diagonal Line Graphic Ellipse Graphic Field Graphic Symbol Object Delete...
Page 33
Media Tracking Media Type Printing Mirror Image of Label Print Orientation Print Quantity Print Rate Print Width Set Serial Communications Set Darkness Serialization Data Set Date and Time(for Real-Tiime Clock) Start Format Recall Format Recall Graphic End Format...
21. Utilities The following utilities and concerned manual can be found on the CD or homepage. Name Description SEWOO Label Printer Configuration Tool. This program provides the following functions. - Set Ethernet and RS232 - Set beep sound for each error...
22. S/W We provides SDK, Driver, etc. as follows to respond to various S/W usage environments. You can download this S/W from the homepage. Name Description This is an install program used to print a label printer in Windows OS. Windows Driver After installing the Windows Driver, you can use a program like Label Cooker.
Need help?
Do you have a question about the LK-B24 and is the answer not in the manual?
Questions and answers