Related Manuals for SEWOO LK-B20 II
Summary of Contents for SEWOO LK-B20 II
- Page 1 Aroot Co., Ltd. 28-6, Gajangsaneopdong-ro, Osan-si, Gyeonggi-do ,18103, Republic of Korea TEL +82-31-8077-5000 / FAX +82-31-624-5310 / http://www.miniprinter.com B20Ⅱ ENG Rev. D 01/2021...
- Page 2 LABEL PRINTER MODEL � LK-B20Ⅱ 4� LABEL PRINTER USER�S MANUAL All specifi cations are subject to change without notice...
- Page 3 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions. 1) This device may not cause harmful interference, and including 2) T his device must accept any interference received, interference that may cause undesired operation. Vic Barczyk 20280 S.
-
Page 4: Table Of Contents
Table of Contents Safety Precautions 1. Unpacking 2. Inspecting The Printer 3. Attaching Power Supply 4. Interface Cable Connection 5. Loading the Paper 6. Loading Ribbon 7. Setting Up the Sensor 8. Self Test 9. Sensor Calibration 10. Cutter Cleaning (option) 11. -
Page 5: Safety Precautions
Safety Precautions For better safety and reliability, adhere to the following precautionary measures. Read and follow the instructions carefully before operation of the product. Indication Prohibition Must follow Unplug the power from the Do not disassemble outlet Grounding to prevent Do not handle the product with electric shock wet hands... - Page 6 WARNING Failure to follow these instructions could result in fire, electric shock, other injuries, or property damage. Do not disassemble, repair or modify the Do not unplug the product. power cable to turn off the product. Potential risk of malfunction, electric Turn off the power shock, or fire.
-
Page 7: Unpacking
1. Unpacking Standard Ribbon Spindle Printer Power Cord Power Supply (2EA) Paper Sp indle Ribbon Core Ribbon Label Manual Optional Auto Cutter Peeler External Paper Supply... -
Page 8: Inspecting The Printer
2. Inspecting The Printer Printer Head Notch Sensor Moving Paper Sensor Paper width Guide Head Release Lever Power Switch Interface Connectors Power Connector Button Upper Cover Knob... - Page 9 CAUTION Make sure to be careful of the HOT head. Opening the printer Open the upper cover by pushing the Place the paper roll as shown. Make sure knob in the direction of the arrow. the paper is placed in the right direction. Closing the paper upper guide Closing the upper cover Make sure you hear the closing sound...
-
Page 10: Attaching Power Supply
3. Attaching Power Supply 220VAC 115VAC Check the specification of the AC power Turn off the power of the printer and cord if it is correct with your power connect the power supply to the printer. system. Connect the AC power cord to the Insert a plug into the outlet. -
Page 11: Interface Cable Connection
4. Interface Cable Connection Printer ETHERNET SERIAL... -
Page 12: Loading The Paper
5. Loading the Paper Turn off the printer and open the upper Rise up the paper upper guide by pulling cover by pushing the in the direction of the head release lever. the arrow. Paper Fixing Tap Open the paper width guide by Pull out one of the adjustable width pushing it to the right &... - Page 13 Insert paper roll into the printer. Adjust the paper width guide to meet the paper width. Push the head stopper release lever Close the upper cover and make sure in the direction of the arrow until the you hear the closing sound of the paper upper guide comes down.
-
Page 14: Loading Ribbon
6. Loading Ribbon Ribbon Ribbon Spindle Remove the vinyl covering on the Insert one side of the ribbon spindle. ribbon. Depress the indicated button on the ribbon spindle while inserting the ribbon roll. detail A Push the other side of the ribbon spindle down to secure it. Pull out the ribbon edge through ribbon mechanism as shown in the picture. - Page 15 Insert one side of the ribbon spindle. Push the other side of the ribbon spindle down to secure it. Attach the ribbon to the core with tape Turn the adjustment knob in the arrow as shown. direction to tighten the ribbon.
-
Page 16: Setting Up The Sensor
7. Setting Up The Sensors Set Black Mark Sensor right to the size Locate notch sensor on the same number of roll paper. point- as the black mark sensor is indicating on. **0 is the initialization number for sensor of the product.** Black Mark Sensor and Notch sensor must always point to the same number. -
Page 17: Self Test
8. Self Test Turn off the printer. While holding down the feed button, turn on the printer. The printer starts printing some basic information. Also, if you press the pause button 3 times after turning on the power, the printer starts printing the same information. -
Page 18: Sensor Calibration
The printer will be stopped after a graph is printed. Then, you can use the printer. If the calibration result is abnormal, set it up in "SEWOO Label Printer Configuration Tool" and then try again. This utility is on the CD and can be... -
Page 19: Cutter Cleaning (Option)
10. Cutter Cleaning (option) Lift the cutter diagonally and separate it from the printer. Separate the socket connected inside from the printer. - Page 20 Pull out 2 screws on the back of the Clean the fixed blade and cutting edge cutter with a screwdriver and demount by wiping a cotton bud with a cleansing the plate. lotion or alcohol. After cleansing, assemble it in reverse order.
-
Page 21: Peripherals Connection (Option)
11. Peripherals Connection (option) This product can communicate with other devices via Wi-Fi & Bluetooth communication and cable. 11-1. Wi-Fi Connection 1 The Printer can be connected to devices equipped with Wi-Fi communication capacity (PDAs, PCs, etc.) 2 Use the Wi-Fi connection function supported by the device to connect to the printer. NOTE - Refer to the Wi-Fi Configuration Tool and manual from the homepage. -
Page 22: Interface
12. Interface Interface Connectors Standard 9 Pin Serial Ethernet... - Page 23 9Pin Serial Interface Signal Description Input Printer receive data line RS-232C level Output Printer transmit data line RS-232C level 6, 8 Output Printer handshake to host line RS-232C level System Ground Input Data Send Ready 1, 7, 9 USB Interface Signal Description DATA-...
-
Page 24: Media Roll Size
13. Media Roll Size Core Diameter(A) 25.4 or 38.1 mm (1.0 or 1.5 inches) Max. width 118 mm (4.65inches) Roll Max.diameter(B) 125 mm (5 inches) Max.media width(C) 116 mm (4.57 inches) Min.media width(C) 38.1 mm (1.5 inches) Max.media thickness 0.15 mm (0.006 inches) Min.mdeia thickness 0.06 mm... -
Page 25: Labels
14. Labels <-- a --> Media width (inch, liner) Maximum 116.0 mm (4.57 inches) Minimum 38.1 mm (1.5 inches) <-- b --> Label length Minimum 10 mm (0.39 inches) <-- c --> Label gap height Maximum 10 mm (0.39 inches) Minimum 2 mm (0.08 inches) -
Page 26: Tags And Strip With Slots
15. Tags and Strip with Slots <-- a --> Media width (inch, liner) Maximum 116.0 mm (4.57 inches) Minimum 38.1 mm (1.5 inches) <-- b --> Label length Minimum 10 mm (0.39 inches) <-- c --> Label gap height Minimum 14 mm (0.55 inches) Liner... -
Page 27: Tags And Strip With Black Marks
16. Tags and Strip with Black Marks <-- a --> Tag or strip width Maximum 116.0 mm (4.57 inches) Minimum 38.1 mm (1.5 inches) <-- b --> Tag length Minimum 10 mm (0.39 inches) <-- c --> Black mark width Minimum 14 mm (0.55 inches) -
Page 28: Plain Continuous Stock
17. Plain Continuous Stock The printer can use continuous stock without any detection slots or black marks. The printer must be set for continuous stock by the Q command. The length of each copy is decided by the size of the print image and any additional media feed is decided by the Q command. -
Page 29: Specifications
18. Specifications Print method Thermal Transfer and Direct Thermal B20Ⅱ Print speed 152mm/sec (Max.) B230Ⅱ 102mm/sec Print width (Max.) 104mm (4 inch) Print length (Max.) 1,000mm B20Ⅱ 203dpi (8 dots/mm) Resolution B230Ⅱ 300dpi (12 dots/mm) Paper width (Min.~Max.) Min. 18 ~ Max. 118mm Internal Paper roll size Ø... - Page 30 MaxiCode, PDF 417, Data Matrix, Barcode QR Code, MicroPDF417, AZTEC 8x12,10x16,12x20,14x24, EPLII 32x48 (5 Bitmap Font) : English, Font 24x24(KSC5601) : Korean specification 5x9,7x11,10x18,15x28,13x26,40x60, ZPLII 13x21 (7 Bitmap Font), 1 smooth scalable font Windows Printer Driver XP, 2000, 2003, 2008, Driver Vista, 7(32 &...
-
Page 31: Command List
19. Command List ZPL Command List Command Description Scalable/Bitmapped Font Code 11 BarCode Interleaved 2 of 5 BarCode Code 39 BarCode Code 49 BarCode Planet Code BarCode PDF417 BarCode EAN-8 BarCode UPC-E BarCode Code 93 BarCode Code 128 BarCode(Subsets A, B, and C) UPS MaxiCode BarCode EAN-13 BarCode Micro-PDF417 BarCode... - Page 32 Command Description Download Graphics Field Block Field Clock(for Real-Time Clock) Field Data Field Hexadecimal Indicator Field Number Field Origin Field Parameter Field Reverse Print Field Separator Field Typeset Field Variable Field Orientation Comment Graphic Box Graphic Circle Graphic Diagonal Line Graphic Ellipse Graphic Field Graphic Symbol...
- Page 33 Command Description Media Tracking Media Type Printing Mirror Image of Label Print Orientation Print Quantity Print Rate Print Width Set Serial Communications Set Darkness Serialization Data Set Date and Time(for Real-Tiime Clock) Start Format Recall Format Recall Graphic End Format RFID Command Command Description...
-
Page 34: Utilities
20. Utilities The following utilities and concerned manual can be found on the CD or homepage. Name Description SEWOO Label Printer Configuration Tool. This program provides the following functions. - Set Ethernet and RS232 - Set beep sound for each error... -
Page 35: S/W
21. S/W We provides SDK, Driver, etc. as follows to respond to various S/W usage environments. You can download this S/W from the homepage. Name Description This is an install program used to print a label printer in Windows OS. Windows Driver After installing the Windows Driver, you can use a program like Label Cooker.
Need help?
Do you have a question about the LK-B20 II and is the answer not in the manual?
Questions and answers