Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for SEWOO LK-B230
Summary of Contents for SEWOO LK-B230
- Page 1 SEWOO TECH CO.,LTD. 374-2, Gajang-dong, Osan-si, Gyeonggi-do, 447-210, Korea TEL : +82-31-459-8200 FAX : +82-31-459-8880 www.miniprinter.com MODEL : LK-B230 4” DESKTOP LABEL PRINTER All specifications are subject to change without notice B230 Rev. B 06/13...
-
Page 2: Table Of Contents
Table of Contents 1. Safety Caution 2. Unpacking 3. Inspecting the Printer 4. Attaching Power Supply 5. Hooking Up the Printer and Computer 6. Loading the Paper 7. Loading Ribbon 8. Setting Up the Sensors 9. Self Test 10. Interface 11. -
Page 3: Safety Caution
1. Safety Caution For higher reliability and safety, consider the following precautionary measures. WARNING Read and follow the instructions carefully before running of the product. Failure to follow these instructions could result in fire, electric shock, or other injuries, or property damage Indication Prohibition Must follow... -
Page 4: Unpacking
2. Unpacking 3. Inspecting the printer Printer Power Cord(1EA) Interface Connectors Power Switch Printer Head Power Supply Ribbon Label Notch Sensor Moving Paper Sensor Ribbon Core Ribbon Spindle (2EA) Paper Spindle Paper width Guide Head Release Lever Manual Power Connector Button Upper Cover Knob... -
Page 5: Attaching Power Supply
4. Attaching Power Supply Opening the printer 220VAC 115VAC Open the upper cover by pushing the knob in Make sure to be careful of the HOT head the direction of the arrow Check the specification of the AC power cord Turn off the power of the printer and connect if it is correct with your power system the power supply to the printer... -
Page 6: Hooking Up The Printer And Computer
5. Hooking Up the printer and computer 6. Loading the Paper -Printer- Parallel -Computer- Turn off the printer and open the upper cover by Rise up the paper upper guide by pulling the pushing the in the direction of the arrow. head release lever Paper Fixing Tap Make sure the printer is turned off then connect the printer to the PC... -
Page 7: Loading Ribbon
7. Loading Ribbon Ribbon Ribbon Spindle Insert paper roll into the printer Adjust the paper width guide to meet the paper Remove the vinyl covering on the ribbon. Insert one side of the ribbon spindle width Depress the indicated button on the ribbon spindle while inserting the ribbon roll. -
Page 8: Setting Up The Sensors
8. Setting up the sensors Insert one side of the ribbon spindle Push the other side of the ribbon spindle down Set Black Mark Sensor right to the size of roll Locate notch sensor on the same number point- to secure it. paper as the black mark sensor is indicating on. -
Page 9: Self Test
9. Self Test 10. Interface Interface Connectors Standard <USB “B”Type> <Centronics Parallel> Option Turn off the printer While holding down the feed button, turn on the printer <9 Pin Serial> <Ethernet> <Wi-fi> Set free the feed button The printer starts printing some basic information... -
Page 10: Media Roll Size
11. Media Roll Size 9Pin Serial Interface Signal Description Input Printer receive data line RS-232C level Output Printer transmit data line RS-232C level Output Printer handshake to host line RS-232C level System Ground Input Data Send Ready 1,7,9 Centronics Parallel Interface Signal Description STROBE-... -
Page 11: Labels
12. Labels 13. Tags and Strip with Slots <-- a --> Media width (inch, liner) <-- a --> Tag or strip width Maximum 116.0 mm (4.57 inches) Maximum 116.0 mm (4.57 inches) Minimum 38.1 mm (1.5 inches) Minimum 38.1 mm (1.5 inches) <-- b -->... -
Page 12: Tags And Strip With Black Marks
14. Tags and Strip with Black Marks 15. Plain Continuous Stock The printer can use continuous stock without any detection slots or black marks. <-- a --> Tag or strip width The printer must be set for continuous stock by the Q command. Maximum 116.0 mm (4.57 inches) -
Page 13: Specifications
16. Specifications Product Specifications Font Specification 7bitmapped (5x9, 7x11, 10x18, 15x28,13x26, 40x60, 13x21) Print method Thermal Transfer and Direct Thermal 1 smooth scalable Print speed(max) 102mm/sec DRIVER Windows Printer Driver(7, XP, 2000, 2003, Print width(max) 104mm (4.1”) 2008, Vista (32 & 64bit) Print length(max) 650mm (25.59”) Weight... -
Page 14: Command List
17. Command List ZPL Command List Command Description Field Parameter Command Description Field Reverse Print Scalable/Bitmapped Font Field Separator Code 11 BarCode Field Typeset Interleaved 2 of 5 BarCode Field Variable Code 39 BarCode Field Orientation Code 49 BarCode Comment Planet Code BarCode Graphic Box PDF417 BarCode... - Page 15 RFID Command Command Description ^HL or ~HL Return RFID Data Log to Host Read or Write RFID Format Get RFID Tag ID Specify RFID Retries for a Block Set Up RFID Parameters Write(Encode) Tag...
Need help?
Do you have a question about the LK-B230 and is the answer not in the manual?
Questions and answers