SEWOO LK-B24 Manual
Hide thumbs Also See for LK-B24:

Advertisement

J. STEPHEN Lab., Ltd.
28-6, Gajangsaneopdong-ro, Osan-si, Gyeonggi-do , 447-210 Republic of Korea
TEL : +82-31-8077-5000 FAX : +82-31-459-8880
www.miniprinter.com
MODEL : LK-B24
LABEL PRINTER
All specifications are subject to change without notice
B24 Rev. D 10/16

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LK-B24 and is the answer not in the manual?

Questions and answers

Summary of Contents for SEWOO LK-B24

  • Page 1 J. STEPHEN Lab., Ltd. 28-6, Gajangsaneopdong-ro, Osan-si, Gyeonggi-do , 447-210 Republic of Korea TEL : +82-31-8077-5000 FAX : +82-31-459-8880 www.miniprinter.com MODEL : LK-B24 LABEL PRINTER All specifications are subject to change without notice B24 Rev. D 10/16...
  • Page 2: Table Of Contents

    Table of Contents 1. SAFETY CAUTION 2. UNPACKING 3. PRINTER IDENTIFICATION 4. CONNECTING POWER SUPPLY 5. HOOKING UP THE PRINTER AND COMPUTER 6. LOADING THE PAPER 7. LOADING RIBBON 8. THE TREATMENT WHEN YOU RUN SHORT OF PAPER AND ENCOUNTER CUTTER JAM PROBLEM 9.
  • Page 3: Safety Caution

    1. Safety Caution For higher reliability and safety, consider the following precautionary measures. WARNING Read and follow the instructions carefully before running of the product. Failure to follow these instructions could result in fire, electric shock, or other injuries, or property damage Indication Prohibition Must follow...
  • Page 4: Unpacking

    2. Unpacking 3. Printer identification Printer Interface cable (USB) Interface Power Printer Paper width Guide Printer Head Power supply Power Cord(1EA) Black Mark Sensor Gap Sensor Button CD (Manual and Software) Quick Manual Upper Cover Knob Power Switch...
  • Page 5: Connecting Power Supply

    4. Connecting power supply Opening the printer Power Connectors Open the upper cover by pushing the knob in the Make sure to be careful of the HOT head after direction of the arrow. using long time. Please check the specification of the AC power Turn off the power of the printer and connect cord if it is correct with your power system.
  • Page 6: Hooking Up The Printer And Computer

    5. Hooking up the printer and computer 6. Loading the paper -Printer- Turn off the printer and open the upper cover by Please open the upper cover as shown above pushing the knob in the direction of the arrow ETHERNET SERIAL Please open as shown above.
  • Page 7: Loading Ribbon

    7. Loading Ribbon Make sure that install adjusting the groove. Direction of Ribbon Loading Change paper core size adjusting push button of Label Paper Guide. - Ribbon - - Paper Core - Install the ribbon to the right side first Adjust the paper width guide to meet the - 1 inch - - 1.5 inch -...
  • Page 8: The Treatment When You Run Short Of Paper And Encounter Cutter Jam Problem

    The treatment when you run short of paper and encounter cutter jam problem Install a paper core adjusting the groove, New ribbon has sticker in the end, so that tape otherwise a paper core can be fallen. is not necessary. In case that ribbon doesn’t have sticker, please use tape.
  • Page 9: Setting Up The Sensors

    10. Sensor Calibration 9. Setting up the sensors Black Mark Sensor Note Press once. Power switch sig during 2~3 seconds. Set Black Mark Sensor right to the size of roll paper Sensor Calibration should be proceeded by pressing button power and feed for 2~3 seconds at the same time regardless power status ( Power On or Off ) GAP Sensor...
  • Page 10: Pause Function

    11. Pause function 12. Printer cleaning If the interior of the printer is dusty, printing quality can lowered. In such a case, follow the instructions below to clean up the printer. Note Pause & Restart Press FEED KEY Once. NOTE 1.
  • Page 11: Connector

    13. Connector Ethernet Interface Interface Connectors Signal Data Out + Output Data + Data Out - Output Data - Ground Data IN + Input Data + Data IN - Input Data - USB Interface Signal Description <USB “ B “ TYPE> <...
  • Page 12: Standard Roll Media Specification

    14. Standard roll media specification 15. Standard label specification <-- a --> Media width (inch, liner) Maximum 114 mm Minimum 18 mm <-- b --> Label length Minimum 10 mm <-- c --> Label gap height Maximum 10 mm Minimum 2 mm Liner Opacity...
  • Page 13: Label Specification With Through-Hole

    16. Label specification with Through-hole 17. Label with Black Mark Tag or strip width <-- a --> <-- a --> Tag or strip width Maximum 114 mm Maximum 114 mm Minimum 18 mm Minimum 18 mm Tag length <-- b --> <-- b -->...
  • Page 14: Continuous Stock Specification

    18. Continuous stock specification 19. Specifications The printer can use continuous paper without any detection gap or black marks. Product Specifications Print method Direct Thermal Continuous paper cannot be used in the Test (Dump) Mode. Print speed(max) 127mm/sec <-- a --> Maximum 114mm Print width(max)
  • Page 15 Certification (1) FCC PART15 CLASS A CE EMCD (CE-EMCD Class B) (3) UL/cUL (UL 60950-1) ♣“This equipment is indoor use and all the communication wiring are limited to inside of the building” or similar text. Electrical Characteristics (1) Input Voltage DC 24V ±...

Table of Contents