Related Manuals for SEWOO LK-B30IIE
Summary of Contents for SEWOO LK-B30IIE
- Page 1 Aroot Co., Ltd. 28-6, Gajangsaneopdong-ro, Osan-si, Gyeonggi-do ,18103, Republic of Korea TEL +82-31-8077-5000 / FAX +82-31-624-5310 / http://www.miniprinter.com B30ⅡE ENG Rev.A 10/2023...
- Page 2 LABEL PRINTER MODEL : LK-B30ⅡE 4” Direct Thermal Label Printer All specifications are subject to change without notice...
- Page 3 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions. 1) This device may not cause harmful interference, and including 2) T his device must accept any interference received, interference that may cause undesired operation. Tim Kloeker 20280 S.
- Page 4 For USA Information to user; Caution: The user that changes or modifications not expressly approved by the Aroot Co., Ltd., responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
- Page 5 For Canada This class A digital apparatus complies with Canadian ICES-003 (A) Cet appareil num rique de la class A est conforme la norme NMB-003 (A) du Canada The antenna cannot be removed (and changed) by user. NOTE This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
-
Page 6: Table Of Contents
Table of Contents Safety Precautions 1. Unpacking 2. Inspecting The Printer 3. Connecting power supply 4. Hooking up the printer and computer 5. Loading the media 5-1. Roll paper Type 5-2. Fanfold Type 5-3. Load Fanfold Cover 5-4. Remove Fanfold cover 6. - Page 7 11. Option 11-1. Cutter Assembly 11-2. Peeler Assembly 12. Printer cleaning 13. Peripheral Connection (Optional) 13-1. Bluetooth Connection 13-2. Wi-Fi Connection 14. Connector 15. Standard roll media specification 16. Standard label specification 17. Label specification with Through-hole 18. Label with Black Mark 19.
-
Page 8: Safety Precautions
Safety Precautions For better safety and reliability, adhere to the following precautionary measures. Read and follow the instructions carefully before operation of the product. Indication Prohibition Must follow Unplug the power from the Do not disassemble outlet Grounding to prevent Do not handle the product with electric shock wet hands... - Page 9 WARNING Failure to follow these instructions could result in fire, electric shock, other injuries, or property damage. Do not disassemble, repair or modify the Do not unplug the product. power cable to turn Potential risk of off the product. malfunction, electric Turn off the power shock, or fire.
-
Page 10: Unpacking
1. Unpacking Standard Printer Fanfold Cover Power Supply Paper Spindle Power Cord Manual Optional Auto Cutter Peeler & Peeler bar... -
Page 11: Inspecting The Printer
2. Inspecting The Printer the symbol means direct current Power Serial Ethernet Power Switch Printer Head Notch Sensor Black Mark Sensor FEED Button Upper Cover Knob... - Page 12 Opening the printer Open the upper cover by pushing the CAUTION knob in the direction of the arrow. Make sure to be careful of the HOT head after using long time. "If the cover is not shut down completely, the printer may not work properly" Please make sure you hear the closing sound of the upper cover.
-
Page 13: Connecting Power Supply
3. Connecting power supply 220VAC Power Connectors 115VAC Please check the specification of the Turn off the power of the printer and AC power cord if it is correct with your connect the power supply to the printer power system. as shown above. -
Page 14: Hooking Up The Printer And Computer
4. Hooking up the printer and computer Printer SERIAL ETHERNET... -
Page 15: Loading The Media
5. Loading the media 5-1. Roll paper Type Turn off the printer and open the Please open the upper cover as shown upper cover by pushing the knob in the above. direction of the arrow. Paper Spindle Pull out one of the adjustable width Insert paper roll into the printer. - Page 16 Adjust the paper guide to fit the width of the paper. " Please cut the paper in upper direction " Pull the paper to the print position and Make sure that you hear the closing sound when the top cover is fully closed.
-
Page 17: Fanfold Type
5-2. Fanfold Type Turn off the printer and open the upper cover by pushing the knob in the direction of the arrow. Please open the upper cover as shown above. - Page 18 Insert a paper roll into the printer. " Please cut the paper in upper direction " Close the upper cover completely. - Make sure you hear the closing sound.
-
Page 19: Load Fanfold Cover
5-3. Load Fanfold Cover Open the upper cover and put the Fanfold Pushing fanfold cover from up to down cover into the guide hook as shown above. and set. Back side of printer loaded fanfold cover... -
Page 20: Remove Fanfold Cover
5-4. Remove Fanfold cover Pull out the left edge of the fanfold cover When the edge widen, pull the fanfold using an angled tool. cover upwards to remove it. Back side of printer removed fanfold cover NOTE - Please remove fanfold cover when using fanfold type paper. -
Page 21: T He Treatment When You Run Short Of Paper And Encounter Cutter Jam Problem
6. T he treatment when you run short of paper and encounter cutter jam problem While you are printing with continuous media, please press PULL lever to the direction of the arrow. " Installation of the new paper "... -
Page 22: Setting Up The Sensors
7. Setting up the sensors Black Mark Sensor Notch Sensor Set Black Mark Sensor right to the size The sensor is fixed, so no further of roll paper. adjustment is required. Adjust the arrows to face each other in the same position. -
Page 23: Self-Test Printing / Configuration Printout
8. S elf-Test Printing / Configuration Printout 8-1. Self-Test printing when printer power is off 1 While pressing the “FEED” button, power on the printer and then release the “FEED” button at the start of printing. 2 After the printout is completed, printer returns to the READY mode. NOTE - Power Switch meaning... -
Page 24: Self-Test Printing When Printer Power Is On
8-2. Self-Test printing when printer power is on 1 Press the “FEED” button until after the sound of two beeps. Then release the “FEED” button. 2 After the printout is completed, printer returns to READY mode. NOTE - If the “FEED” button is released after only one beep, the printer goes into the Media Calibration function. -
Page 25: Media Calibration
READY mode. NOTE - If the printing result is abnormal after the media calibration, please use the "SEWOO Label Printer Configuration Tool“ to configure correctly. This utility is on the CD or can be downloaded from the... -
Page 26: Media Calibration When Printer Power Is On
9-2. Media Calibration when printer power is on Press the “FEED” button and release immediately after the first beep. NOTE - At the sound of the second beep, the printer goes into the Self Test function and prints out the printer’s configuration. The printer is going to print out the media with the graph indicating how calibration is done for the sensor. -
Page 27: Offline Printer Reset Function
10. Offline Printer Reset Function - The LK-B30IIE can be reset without being connected to the computer. 1 With the printer powered on, pressing the “FEED” button will produce a beep sound every 1 second. Hold the “FEED” button and release at the third beep to enter the printer reset function. -
Page 28: Cutter Assembly
11. Option 11-1 Cutter Assembly This equipment is not suitable for use in locations where children are likely to be present. Moving parts ※ Keep body parts away from cutter blades. Open the paper cover. - Page 29 Lift the front cover to disassemble. Connect the cutter connector to cutter Assemble the cutter to the left and right position. connections and install it down. NOTE - left and right positions are correctly Assembled.
- Page 30 After passing the paper through the cutter mechanism, adjust the guide to fit the width. Close the paper cover.
-
Page 31: Peeler Assembly
11-2 Peeler Assembly Open the paper cover. Lift the front cover to disassemble. Fix the peeler bar according to the order Connect the peeler connector to peeler as shown in the picture. position. - Page 32 NOTE - left and right positions are correctly Assembled. Assemble the filler to the left and right Open the peeler to the front as shown. connections and install it down. Please put the paper in and remove the Move the backing paper that has passed label.
- Page 33 Return the peeler mechanism to normal Close the paper cover. position. 9 10 It is recommended that you use it after checking if the label paper and the back paper are separated when the printout is printed.
-
Page 34: Printer Cleaning
12. Printer cleaning If the interior of the printer is dusty, printing quality can be lowered. In such a case, follow the instructions below to clean up the printer. NOTE 01 Make sure to turn the printer power off prior to cleaning. 02 Regarding printhead cleaning, as the printhead gets very hot during printing, turn off the printer power and wait approximately 10 minutes before cleaning. -
Page 35: Peripheral Connection (Optional)
13. Peripheral Connection (Optional) This product can communicate with other devices via Bluetooth & Wi-Fi communication and cable. 13-1. Bluetooth Connection 1 The Printer can be connected to devices equipped with Bluetooth communication capabilities (PDAs, PCs, etc.). 2 Use the Bluetooth connection function supported by your device to connect to the printer. -
Page 36: Connector
14. Connector Interface Connectors USB “ B “ TYPE 9 Pin Serial Ethernet... - Page 37 Ethernet Interface Signal Data Out + Output Data + Data Out - Output Data - Ground Data IN + Input Data + Data IN - Input Data - USB Interface Signal Description DATA- Printer transmit data line DATA+ Printer transmit data line System Ground 9Pin Serial Interface Signal...
-
Page 38: Standard Roll Media Specification
15. Standard roll media specification Core Diameter(A) 25.4mm Max. width 116mm Roll Max.diameter(B) 127 mm Max.media width(C) 116 mm Min.media width(C) 25.4 mm Max.media thickness 0.20 mm Min.mdeia thickness 0.06 mm NOTE 01 When the paper width is less than 25.4 (1inch), please print 101.6 mm/s. 02 When the paper width is between 25.4 (1inch) to 76.2 (3inch), please print 127mm/s. -
Page 39: Standard Label Specification
16. Standard label specification <-- a --> Media width (inch, liner) Maximum 116 mm Minimum 25.4 mm <-- b --> Label gap height Maximum 10 mm Minimum 2 mm... -
Page 40: Label Specification With Through-Hole
17. Label specification with Through-hole <-- a --> Tag or strip width Maximum 116 mm Minimum 25.4 mm <-- b --> Detection slot width Minimum 14 mm <-- c --> Detection slot height Maximum 10 mm Minimum 2 mm... -
Page 41: Label With Black Mark
18. Label with Black Mark <-- a --> Tag or strip width Maximum 116 mm Minimum 25.4 mm <-- b --> Black mark width Minimum 14 mm <-- c --> Black mark height Maximum 10 mm Minimum 3 mm TICKETS,TAGS, & CONTINUOUS STRIP... -
Page 42: Continuous Stock Specification
19. Continuous stock specification The printer can use continuous paper without any detection gap or black marks. The printer must be set for continuous paper by the Q command. The length of each copy is decided by the size of the print image and any additional media feed is decided by the Q command. -
Page 43: Specifications
20. Specifications Print method Direct Thermal Print speed (Max.) 152mm/sec Print width (Max.) 108mm (4.25 inch) Print length (Max.) 1000mm (39.3”) Resolution 203dpi (8 dots/mm) Paper width (Min.~Max.) 25.4 ~ 115mm (1” ~ 4.52”) Paper roll size 25.4mm (1”) Paper thickness 0.06 ~ 0.20 mm Roll, Fanfold, Blackmark, Continuous, Gap, Paper type... - Page 44 Type External SMPS Power 100 ~240Vac, 2.0A, 50~60Hz 24 Vdc 2.5A Operating Temperature 5℃ ~ 40℃ Storage Temperature -20℃ ~ 60℃ Weight 3.3lbs (1.52kg) 190 x 262 x 168 (mm) / Size (W x D x H) 7.48 x 10.31 x 6.61 (Inch) Option Auto Cutter, Peeler Electrical Characteristics...
-
Page 45: Command List
21. Command List ZPL Command List Command Description Scalable/Bitmapped Font Code 11 BarCode Interleaved 2 of 5 BarCode Code 39 BarCode Code 49 BarCode Planet Code BarCode PDF417 BarCode EAN-8 BarCode UPC-E BarCode Code 93 BarCode Code 128 BarCode(Subsets A, B, and C) UPS MaxiCode BarCode EAN-13 BarCode Micro-PDF417 BarCode... - Page 46 Download Graphics Field Block Field Clock(for Real-Time Clock) Field Data Field Hexadecimal Indicator Field Number Field Origin Field Parameter Field Reverse Print Field Separator Field Typeset Field Variable Field Orientation Comment Graphic Box Graphic Circle Graphic Diagonal Line Graphic Ellipse Graphic Field Graphic Symbol Object Delete...
- Page 47 Media Tracking Media Type Printing Mirror Image of Label Print Orientation Print Quantity Print Rate Print Width Set Serial Communications Set Darkness Serialization Data Set Date and Time(for Real-Tiime Clock) Start Format Recall Format Recall Graphic End Format...
-
Page 48: Utilities
22. Utilities The following utilities and concerned manual can be found on the CD or homepage. Name Description SEWOO Label Printer Configuration Tool. This program provides the following functions. - Set Ethernet and RS232 - Set beep sound for each error... -
Page 49: S/W
23. S/W We provides SDK, Driver, etc. as follows to respond to various S/W usage environments. You can download this S/W from the homepage. Name Description This is an install program used to print a label printer in Windows OS. Windows Driver After installing the Windows Driver, you can use a program like Label Cooker. - Page 50 QR Page...
Need help?
Do you have a question about the LK-B30IIE and is the answer not in the manual?
Questions and answers
how to add in arabic word or diffirence languages
To add Arabic or different languages to the SEWOO LK-B30IIE, use the ^CI command to change the international font or encoding. This command allows switching to a character set that supports the desired language.
This answer is automatically generated