Table of Contents
Advertisement
Quick Links
4600 Heavy Duty Designer Deadlatch Handles With
4300, 4500, and 4900 Series Deadlatches
Tools and Equipment Needed ........................................................................................................ 2
Preparing the Stile ........................................................................................................................... 2
Offsetting the Escutcheon for 31/32" [24.61 mm] and 1-1/8" [28.58 mm] Backset ........................ 4
Optional Monitoring Switch ............................................................................................................. 4
Installing Trim to Stile ...................................................................................................................... 5
Installing the Handle ........................................................................................................................ 6
Determining and Changing the Handing Configuration .................................................................. 7
Changing the Handing of the 4581 Cam Disc................................................................................. 7
1
Installation Instructions
TABLE OF CONTENTS
Phoenix, AZ
Tel: 1-800-872-3267
Mon-Fri: 6:00am - 4:00pm PDT
Fax: 1-800-232-7329
www.adamsrite.com
80-0180-418, Rev D
Advertisement
Table of Contents
Related Manuals for Assa Abloy ADAMS RITE 4300 Series
Summary of Contents for Assa Abloy ADAMS RITE 4300 Series
- Page 1 Phoenix, AZ Tel: 1-800-872-3267 Mon-Fri: 6:00am - 4:00pm PDT Fax: 1-800-232-7329 www.adamsrite.com 4600 Heavy Duty Designer Deadlatch Handles With 4300, 4500, and 4900 Series Deadlatches Installation Instructions TABLE OF CONTENTS Tools and Equipment Needed ......................2 Preparing the Stile ........................... 2 Offsetting the Escutcheon for 31/32”...
- Page 2 IMPORTANT: This product must be installed according to all applicable building and life safety codes! Tools and Equipment Needed The following common hand tools are needed for installation: • 7/32” [5.56 mm], 1/4” [6.35 mm], and 3/8” [9.53 mm] drill bits •...
- Page 3 Inches [Millimeters] Figure 1. Rivnut Installation for 31/32” [24.61 mm] and 1-1/8” [28.58 mm] Backset, Single Lever Figure 2. Rivnut Installation for 1-1/2” [38.1 mm] Backset, Single Lever 80-0180-418, Rev D...
- Page 4 Offsetting the Escutcheon for 31/32” [24.61 mm] and 1-1/8” [28.58 mm] Backset 1. LOOSEN the two #4-40 x 1/4” flat head screws securing the adjustable cover on the back of the trim cartridge until the cover can be slid (see Figure 3, “Adjustable Cover and Trim Cartridge”).
- Page 5 1. WIRE the optional monitor switch in accordance with Table 1, “Wire Colors and Maximum Switching Current,” and Figure 5, “Example Wiring Diagram with N.O. Monitoring.” Table 1. Wire Colors and Maximum Switching Current Wire Color Label Black Common Contact White Normally Open Contact (N.O.) Normally Closed Contact (N.C.)
- Page 6 Figure 6. Installing Trim to Stile Installing the Handle INSERT washer and then INSERT hub over the shaft, as required (see Figure 7, “Installing the Handle”). INSTALL the handle over the hub with the hole aligned with the hole on the hub (see Figure 7).
- Page 7 Determining and Changing the Handing Configuration 1. DETERMINE the current handing configuration(see Figure 8, “Handing Configuration”). Figure 8. Handing Configuration NOTE: During the next step, it is necessary to hold the monitor slide down to keep it from popping out of place by the slide return spring. 1.
- Page 8 SLIDE it in the dowel pin and up to the front push cap. 4. Release the rear push cap to complete the changing hand operation. © 2015, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company. 80-0180-418, Rev D...
Need help?
Do you have a question about the ADAMS RITE 4300 Series and is the answer not in the manual?
Questions and answers