Advertisement

Installation Manual
Impaq SC-W
INS876-1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Impaq SC-W and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Texecom Impaq SC-W

  • Page 1 Installation Manual Impaq SC-W INS876-1...
  • Page 2: Table Of Contents

    Content 1.0 Introduction ..........................2.0 Initial configuration & learning on ..................2.1 DIP switch configuration ...................... 2.2 Additional inputs 1&2 ......................2.3 Learning the device to the system ..................2.4 Using the device with a roller shutter contact ..............3.0 Wireless range test ........................
  • Page 3: Introduction

    1.0 Introduction The Impaq SC-W is a wireless shock sensor with an on board magnetic contact. The product can also be used with an externally wired magnetic contact and has an additional facility for use with window shutter movement detectors.
  • Page 4 INS876-1 4/15...
  • Page 5: Initial Configuration & Learning On

    Icon Item Function select DIP switch Battery Magnet sensor Sensitivity selection button External input terminal block 2.0 Initial configuration & learning on 2.1 DIP switch configuration Each switch controls one sensor (shown below). The DIP switches should be changed after the device is learnt to the system (unless you are only using the device as a Ricochet wireless repeater).
  • Page 6: Additional Inputs 1&2

    2.2 Additional inputs 1&2 The Impaq SC-W has 2 additional inputs. These may be used for any normally closed output device and utilise wireless transmission to the receiver. Typical examples for use are: Any locally powered device with a normally closed output e.g. Smoke detectors, Glass Break detectors, Movement Sensors, Flood detectors etc.
  • Page 7: Using The Device With A Roller Shutter Contact

    2.4 Using the device with a roller shutter contact The Impaq SC-W can be used with retracting cord contacts to protect door and window roller shutters. These are particularly useful when the shutter is left in a partially open position but still needs to be protected against forced entry. The device is compatible with all microswitch 2 wire roller shutter contacts.
  • Page 8: Wireless Range Test

    3.0 Wireless range test The wireless range test is available for the first hour after power up or while the system is in walk test mode – see Premier Elite 8XP-W/32XP-W installation manual. With the device in position, press and hold the sensitivity button for 3 seconds.
  • Page 9: Magnet Positioning

    4.2 Magnet positioning Once the device has been mounted, position the magnet so the notch is aligned with either of the arrow markers on the sides of the PCB, the LED will pulse green indicating a secure state. The magnet can be installed on either side of the device. However, greater sensitivity is achieved by placing the magnet at the bottom right of the device and aligning the notch and the arrow.
  • Page 10 The LED indication for magnet positioning is time limited whilst the system is in commission mode. Figure 5 Side of Axis Approach Min (mm) Removal Max (mm) Device INS876-1 10/15...
  • Page 11 Right Left Once the correct position has been located fix the magnet in place (see figure Figure 6 INS876-1 11/15...
  • Page 12: Setting The Shock Sensitivity

    5.0 Setting the shock sensitivity Within 10 minutes of learning the device (or by activating walk test mode), double press the sensitivity button and the LED will flash blue defaulting to INS876-1 12/15...
  • Page 13 sensitivity setting 2. There are 5 sensitivity settings from 1 to 5 with 1 being the least sensitive (slowest flash rate) and 5 the most sensitive. Each press of the button will change the sensitivity indicated by the flash rate of the blue LED, cycling from slow to fast and finally back to slow after 5 presses.
  • Page 14: Specifications

    -10°C to 55°C Weight 130mm x 26mm x 25mm (magnet 57mm x Dimensions 11.5mm) 7.0 Legal Information Supplier: Texecom Ltd, Haslingden, Lancashire, BB4 4PW, UK. Made in England WEEE Directive: 2012/19/EU (WEEE Directive): Products marked with this symbol INS876-1 14/15...
  • Page 15 Maintenance: Test yearly by the installer. Warranty: 2 year replacement warranty (excludes battery). As the Impaq SC-W is not a complete alarm system, but only a part thereof, Texecom cannot accept responsibility or liability for any damages whatsoever based on a claim that the Impaq SC-W failed to function correctly. Due to our policy of continuous improvement Texecom reserves the right to change specification without prior notice.

Table of Contents

Save PDF