Advertisement
Quick Links
Operation Manual
Sheet Nibbler
61138
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Related Manuals for WilTec 61138
Summary of Contents for WilTec 61138
- Page 1 Operation Manual Sheet Nibbler 61138 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignificantly.
- Page 2 All rights re- served. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 Damaged cables increase the risk of electric shock. • When operating a power tool outside, use an outdoor extension cord. This type of cords is rated for outdoor use and reduce the risk of electric shocks. © by WilTec Wildanger Technik GmbH Item 61138 Page 3 http://www.WilTec.de http://www.aoyue.eu...
- Page 4 When servicing a tool, use only identical and original replacement parts. Follow the instructions in the “maintenance” section of the manual. Use of unauthorised parts or failure to follow mainte- nance instructions may create a risk of electric shock or injury. © by WilTec Wildanger Technik GmbH Item 61138 Page 4 http://www.WilTec.de...
- Page 5 The following shows the symbols used for the tool. Voltage in Volt No load speed Amperage in Ampere Revolutions per minute Frequency in Hertz Protection class II © by WilTec Wildanger Technik GmbH Item 61138 Page 5 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 6 Grease it after finishing the re- placement of the punching needle and the punching die set. (Fig. 3 and 4). © by WilTec Wildanger Technik GmbH Item 61138 Page 6 http://www.WilTec.de http://www.aoyue.eu...
- Page 7 To switch off: Press the back of the switch down to turn it off. Thickness gauge (Fig. 7) The recess of the blanking rod is considered as a measuring scale which indicates the allowable thickness of the die cut. © by WilTec Wildanger Technik GmbH Item 61138 Page 7 http://www.WilTec.de http://www.aoyue.eu...
- Page 8 • To maintain product safety and reliability, repairs or any other maintenance should be performed by and an authorised service partner, always using original replacement parts. © by WilTec Wildanger Technik GmbH Item 61138 Page 8 http://www.WilTec.de http://www.aoyue.eu...
- Page 9 Switch Copper washer Rear cover Mild gear spindle Tapping screw Big gear Cord guard Cylindrical pin Cord Middle cover Opening wrench Baffle plate Socket hex wrench © by WilTec Wildanger Technik GmbH Item 61138 Page 9 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 10 © by WilTec Wildanger Technik GmbH Item 61138 Page 10 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 11 This logo indicates that this electric equipment must not be disposed with the domestic waste. The company WilTec Technik GmbH has been registered in the German registry EAR under the WEEE- registration number DE45283704. Disposal of used electrical and electronic appliances...