Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for IBA ibaPADU-C-8AI
Summary of Contents for IBA ibaPADU-C-8AI
- Page 1 Mains Independent Data Logger Manual Issue 1.11...
- Page 2 However, the information in this publication is updated regularly. Required cor- rections are contained in the following regulations or can be downloaded on the Internet. The current version is available for download on our website http://www.iba-ag.com. Protection note ®...
-
Page 3: Table Of Contents
Manual Table of contents About this manual ................... 4 Target group ....................4 Designations ....................4 Symbols used ....................5 Introduction ..................... 6 Scope of delivery .................... 7 Safety instructions ..................7 Description of the device ................8 Device overview..................... 8 Display elements ................... -
Page 4: About This Manual
Manual ibaPADU-C-8AI About this manual This manual describes the structure, use and operation of the device ibaPADU-C-8AI. Target group This manual addresses, in particular, qualified professionals who are familiar with han- dling electrical and electronic modules as well as communication and measurement tech- nology. -
Page 5: Symbols Used
Manual Symbols used If safety instructions or other notes are used in this manual, they mean: The non-observance of this safety information may result in an imminent risk of death or severe injury: By an electric shock! ... -
Page 6: Introduction
Battery run-time about 19 - 24 h during normal operation Rugged metal housing, DIN rail mountable Analysis software with free license if used to analyze files in *.dat format generated by a licensed iba soft- ware. Issue 1.11... -
Page 7: Scope Of Delivery
Manual Scope of delivery The scope of delivery of an ibaPADU-C-8AI contains the following components: ibaPADU-C-8AI-XX 2-pin Wago F-connector RM 5.08 mm 18x2-pin Wago F-connector RM 3.5 mm USB cable A-B, 70 cm, rollable Strain relief plate ... -
Page 8: Description Of The Device
Manual ibaPADU-C-8AI Description of the device Device overview (1) Operational state display LEDs L1 … L4 (2) S11 key (3) DC input X14 (4) Ethernet interface X22 (5) USB interface X23 (6) Analog/digital inputs X1 Front view Issue 1.11... -
Page 9: Display Elements
Manual Display elements Colored light emitting diodes (LEDs) at the device indicate the operational state. Operational state State L1 (Application) L2 (Battery) L3 (DC input) L4 (USB) Battery is not be- Not plugged Not plugged ing charged or is... -
Page 10: Interfaces
Manual ibaPADU-C-8AI Interfaces 5.4.1 DC input X14 An external power supply (9-30 V, DC) can be connected via the DC input and the inter- nal battery can thus be charged. The device switches to battery operation if there is no external power supply available. -
Page 11: Analog/Digital Inputs X1
Manual 5.4.4 Analog/digital inputs X1 Connection for 8 digital and analog input signals 2 earthing Trigger input Connection plug arrangement of the analog/digital inputs 6 GND 10 GND 10 V 10 V 11 12 GND 13 14 GND... - Page 12 Manual ibaPADU-C-8AI Trigger signal connection The trigger input design is identical to the digital input design. There are 2 ways to con- nect the trigger signal: Signal level against GND Signal level Trigger > 2.2 V active 0.9 V < signal level < 2.2 V undefined <...
-
Page 13: Internal Memory
Manual Internal memory The device has an internal SD memory card with the following directory structure: Directory Contents ibaAnalyzer application config Configuration file config.ini Example of configuration file template_config.ini Directory of the measurement data Directory for log files update Directory in which the update files are copied Issue 1.11... -
Page 14: Commissioning And Configuration
Manual ibaPADU-C-8AI Commissioning and configuration The configuration is done via a text file (config.ini), which is stored in the memory of the device in the directory "config". The file can be accessed and adjustments can be made by a PC connected via the USB or the Ethernet. Subsequently the file is stored in the device memory. - Page 15 Manual Note The entries in the “config.ini” file, which can be modified, are highlighted in yellow in the figure above. Other entries must not be modified. When the network settings are to be activated, the hash signs “#” before the entries “ipAd- dress”, “subnetMask”...
- Page 16 Manual ibaPADU-C-8AI Note The function “automatic shut-down” is a protection against battery discharging. When the device is not active it will be shut down automatically after the time set here. The device will not be shut down, when data capturing is active or when an external power supply is applied via USB or DC.
-
Page 17: Time Synchronization
Manual 7. Close the explorer and remove the device symbol from the system bar with "Securely remove hardware". 8. Briefly press the S11 key or start the device anew to accept the changed configuration file. Note Should the time synchronization be done via the gateway, then the device must have access to the Internet. -
Page 18: Product Information
Manual ibaPADU-C-8AI Note If the timeserver is not available, measurement will be started without synchronization. 6.2.2 Product information The file “product.log” is stored on the device in the “log” directory. It contains important device information, such as hostname, serial number, hardware and firmware versions, MAC address etc. -
Page 19: Start Measurement Process
Manual Start measurement process First connect the input signals with the analog or digital inputs. The measurement can be started in two ways: 6.3.1 Start measurement process manually The manual measurement process is started and stopped by briefly pressing the S11 key. -
Page 20: Reading Measurement Data
Manual ibaPADU-C-8AI Reading measurement data The measurement data file can be read via the USB connection or via the Ethernet con- nection using FTP. When accessing via the Ethernet, the device must not be connected via the USB as a mass storage and a fixed IP address must be configured in the config- uration file "config.ini"... - Page 21 Manual Note The hostname consists of the product name and the 6-digit serial number of the device. You find the serial number on the type label on the device. Example: serial number 000001 Hostname: paduc_000001 The hostname can also be found in the product.log file in the log directory.
-
Page 22: Firmware Update
Manual ibaPADU-C-8AI Firmware update Important Note If you are performing a Firmware update, connect the device to an external power sup- ply! The update could fail if the battery is too week. Do not switch off the device during the update process. -
Page 23: Charging The Battery
The battery charges about 3 times faster via the DC input than via the USB interface. The device can be powered for about 19 - 24 hours with a fully charged battery. The battery is not included in the warranty period given by iba for iba products. Important note The battery must be charged at least every six months to maintain the best possible lifetime. -
Page 24: Technical Data
Manual ibaPADU-C-8AI Technical Data Main data Manufacturer iba AG, Germany Name ibaPADU-C-8AI-Z1 ibaPADU-C-8AI-Z2 (4 GB memory) (32 GB memory) Order number 10.130000 10.130001 Description Mains independent data logger with 8 analog and 8 digital inputs Analog inputs Number Version Single-ended, R/C-Filter 8 kHz, no galvanic isola-... - Page 25 Manual Connection technology signal 36-pin multi-pin connector, plug with clamping inputs technique, enclosed Cable inflexible/flexible (0.2 mm to 1.5 mm) Flexible with cable end sleeve without plastic sleeve (0.25 mm to 1.5 mm) Flexible with cable end sleeve with plastic sleeve (0.25 mm to 0.75 mm)
-
Page 26: Dimensional Drawing
Manual ibaPADU-C-8AI Dimensional drawing (Dimensions in mm) Connection plug arrangement of the analog/digital inputs 6 GND 10 GND 11 12 GND 13 14 GND 15 16 GND 17 18 GND GND 19 20 GND... -
Page 27: Support And Contact
+49 911 97282-33 Email: iba@iba-ag.com Contact: Mr. Harald Opel Shipping address iba AG Gebhardtstr. 10 90762 Fuerth Germany Regional and Worldwide For contact data of your regional iba office or representative please refer to our web site www.iba-ag.com. Issue 1.11...