Table of Contents
Advertisement
Quick Links
Sliding Gate Opener
User Manual GTR211
Please Note: This motor is AC 240V Power only and is not compatible with DC Battery Backup or Solar power.
Gate in closed position
Gate in open position
Viewed from inside the property
WARNING
Instructions must be read before beginning installation. Please follow these instructions carefully, incorrect installation could
affect gate operation. If you require more information, please contact your local Richmond Wheel & Castor Co branch.
AU: 1300 474 246
NZ: 0800 61 71 81 International: +613 9551 2233
For installation or troubleshooting assistance visit gatesupport.richmondau.com
When mounting and positioning the motor ensure that the power cable is unplugged. The motor cover will need to be removed to mount
the motor to the mounting plate. Any changes to the settings of the gate motor can only be made by a licensed electrician.
GTR211 Installation Manual: Rev 1
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Richmond GTR211
Summary of Contents for Richmond GTR211
- Page 1 WARNING Instructions must be read before beginning installation. Please follow these instructions carefully, incorrect installation could affect gate operation. If you require more information, please contact your local Richmond Wheel & Castor Co branch. AU: 1300 474 246 NZ: 0800 61 71 81 International: +613 9551 2233 For installation or troubleshooting assistance visit gatesupport.richmondau.com...
- Page 2 External Remote Receiver (GTR197): Allows the pairing of extra remotes. Up to 250 extra re- motes can be paired with this accessory. Please refer to the relevant manual for each accessory for instructions on wiring them to the GTR211 gate motor. GTR211 Installation Manual: Rev 1...
-
Page 3: Table Of Contents
Programming and Wiring Control Board Diagrams Dip Switch Adjustment Further Settings and Programming 23-25 Troubleshooting Maintenance Clearing and Pairing Remotes Additional instructions for connecting accessories to this motor can be found in the manuals for each accessory. GTR211 Installation Manual: Rev 1... -
Page 4: Gate Opening Default Setting Information
J10 terminal (refer to fig 31 on page 20) Left-Hand Opening: Motor mounted on the left-hand side Fig 02 Any works done to the motor must be completed whilst the power is off and the motor is unplugged GTR211 Installation Manual: Rev 1... -
Page 5: General Safety
Any other use not specified in this documentation could damage the product and be dangerous. • Only use original parts for any maintenance or repair operation. Richmond Wheel & Castor Co declines all responsibility with respect to the automation safety and correct operation when other supplier’s components are used. -
Page 6: Parts List
Limit travel stops (left hand & right hand) Limit travel stop mounting screw M6x18 Masonry Anchor bolt M12x100mm (Drill bit size: M12 Masonry) Motor mounting set screws M10 x 50mm, spring & flat washers GTR211 Installation Manual: Rev 1... -
Page 7: Technical Specifications
Limit switch Spring limit switch Noise Up to 60dB Working duty S2, 20min (20 minutes continuous operation) IP Rating IP54 Maximum Remote Controls to be paired Frequency 433.92 MHz Working temperature -20°C ~ +70°C Fig 03 GTR211 Installation Manual: Rev 1... -
Page 8: Motor Installation Before You Start
Power Supply: The GTR211 requires 1 x 10Amp AC240V 50Hz power supply (RCD Protected Weatherproof PowerPoint). The GTR211 comes complete with a power lead and plug that is 1m long. If you do not have a suitable RCD protected weatherproof power point within 1m of the gate motor you will need to consult a licenced electrician. -
Page 9: Tools Required / Example Sliding Gate Setup
Phillips Head Screwdriver Example Sliding Gate Setup: Gate Track and Gate End Gate Guide Gate Track Wheels Catch Rollers Stopper If you require any gate hardware, contact Richmond Wheel & Castor Co or an authorised reseller. GTR211 Installation Manual: Rev 1... -
Page 10: Step 1 - Gate Preparation Before Adding Your Motor
The motor pad concrete footing requires an area of no less than 450mm long x 300mm wide and a minimum depth of 200mm (Standard requirement). • Ensure surface is level and parallel to the driveway Mounting Plate Dimensions: GTR211 Installation Manual: Rev 1... -
Page 11: Step 3 - Motor Position Installation
• Remove motor from the mounting plate. Fig 03 Sliding Gate Frame (in open position) 21-17mm 53-57mm Mark corners of the mounting plate with a pencil, chalk, or similar. Fig 04 GTR211 Installation Manual: Rev 1... -
Page 12: Step 4 - Removing The Motor Cover For Mounting
Mark the (4) positions for your anchor bolts ready for drilling (refer to Fig 06). • Remove Mounting plate. • Using a M12 masonry drill bit, drill holes to a minimum depth of 120mm (Fig 07). Fig 06 Fig 07 GTR211 Installation Manual: Rev 1... -
Page 13: Step 6 - Fitting The Mounting Plate & Motor
Spring Washer Hand-tighten set screws before final adjustment of motor. Flat Washer Fig 13 Please ensure that the motor power cable is not plugged in at any stage before Step 9 GTR211 Installation Manual: Rev 1... -
Page 14: Step 7 - Gear Rack & Motor Alignment
To put the gate motor into manual mode, insert the In manual mode, the gear can turn freely key and open the manual release bar as shown and the gate can be operated by hand Fig 16 GTR211 Installation Manual: Rev 1... - Page 15 At this stage of final assembly, the cover is removed (not shown) and the power cable is still unplugged. Fig 17 Now that your gear rack and motor are aligned, and your gate is sliding freely, fully tighten the motor mounting set screws (Part 6d) and reinstall motor cover and tighten screws provided. GTR211 Installation Manual: Rev 1...
-
Page 16: Step 8 - Limit Travel Stops
To Reset: When setting new limit travel stop positions please ensure that you turn the power off and then on again. Turning the power off will reset the limit travel stop memory, allowing for new limit travel stop positions to be recognised by the motor. GTR211 Installation Manual: Rev 1... - Page 17 GTR211 in the open Motor position Motor Gear Mounting Plate Fig 22 Please Note: The warning signage provided (Part 5) must be displayed on the street facing side of your automatic gate at all times. GTR211 Installation Manual: Rev 1...
-
Page 18: Step 9 - Powering The Motor
Press the remote control again and the gate will close. • Soft start/soft stop function - The GTR211 is set by default to provide the soft start/soft stop function. We recommend this default position is always maintained. Your motor is now set up for basic remote control operation. -
Page 19: Step 10 - Testing The Limit Travel Stops
When setting new limit travel stop positions please ensure that you turn the power off and then on again. Turning the power off will reset the limit travel stop memory, allowing for new limit travel stop positions to be recognised by the motor. Fig 24 GTR211 Installation Manual: Rev 1... -
Page 20: Programming And Wiring
Programming and Wiring: Control Board Wiring Diagram 01 Any works to the 240V AC must only be performed by a licensed electrician. Ensure power is off before any modifications are made. Fig 25 GTR211 Installation Manual: Rev 1... - Page 21 Programming and Wiring: Control Board Wiring Diagram 02 Fig 26 GTR211 Installation Manual: Rev 1...
-
Page 22: Dip Switch Adjustment
The gate will remain open until closed again with a remote. Optional Automatic Close Function: Richmond strongly recommends that you install infrared photocells if using the motor in auto close mode. 3 OFF 4 ON: automatic close delay time is 12s. -
Page 23: Further Settings And Programming
Rotate VR1 clockwise to increase the stall force, anti-clockwise to decrease. VR3: Slow Start/Stop Width Adjustment For best performance set the torque at the lowest setting that you require. Rotate clockwise to increase, counter-clockwise to decrease. Default setting is at maximum. GTR211 Installation Manual: Rev 1... - Page 24 Ensure that power is off before completing any wiring Using a screwdriver, loosen the Insert the wire into the terminal. Tighten with a screwdriver to screw on the side of the terminal. Refer to pages 20 & 21 secure the wire in place. GTR211 Installation Manual: Rev 1...
- Page 25 Please Note: If changing gate direction terminals 11 & 13 on Terminal J5 will also need to be swapped with each other. J2 Terminal: PE: Earth (yellow/green wire). L: Power (brown wire). N: Power (blue wire). GTR211 Installation Manual: Rev 1...
-
Page 26: Troubleshooting
3. Licensed Electrician: Increase VR1: Stall Force (Page 23). For support or assistance with troubleshooting, visit gatesupport.richmondau.com Or ring your local Richmond Wheel & Castor Branch AU: 1300 474 246 NZ: 0800 61 71 81 International: +613 9551 2233 GTR211 Installation Manual: Rev 1... -
Page 27: Maintenance
This should be checked by a qualified electrician. • Always check the stall force after performing any maintenance. If this function does not work, do not use the gate motor until this is rectified. GTR211 Installation Manual: Rev 1... -
Page 28: Clearing And Pairing Remotes
NZ: 0800 61 71 81 International: +613 9551 2233 Richmond Wheel & Castor Co declines all responsibility for any consequences resulting from improper use of the product, or use which is different from that expected and specified in the present documentation.
Need help?
Do you have a question about the GTR211 and is the answer not in the manual?
Questions and answers