Single gang hdmi usb-c over 164ft / 50m cat6/6a auto switching wall plate switcher transmitter with receiver kit. 4k uhd, 18g, power over cat (12 pages)
(balanced/unbalanced) and digital (PCM) audio de- embed ports feed audio of the selected source into an amplifier, DSP, or sound bar. Integrating KD-UFS42 with KD-AMP220 and KD-CAMUSB will enable an app-ready all-in-one solution for control of video switching, sound and speech enforcement, and PTZ camera control.
Page 4
Lossless Compressed Digital Audio: Dolby® TrueHD, Dolby® Digital Plus, DTS-HD Master Audio™, and Dolby® Atmos • Control System Support: Key Digital® App ready. Compass Control® Pro ready. Fully controllable by all IR, RS-232, and TCP/IP supported control systems via open API. Accessories •...
3. Connect CAT5e/6 cabling from KD-UFS42’s HDBaseT outputs to KD-X40MRX HDBaseT input 4. Connect audio to send audio of the select source into KD-Amp220 use KD-UFS42’s analog audio de- embed port. For other audio systems use the digital or analog outputs ports located on KD-UFS42 or KD-X40MRx.
Configure KD-UFS42 with Key Digital Management Software Pro (KDMS Pro). Download HERE 1. Connect to KD-UFS42 from your PC using the USB micro port on the face of the unit 2. Open the KDMS Pro software and perform a USB scan (fig. 1a). Choose “NO” and Start Scan when the USB Device Scan prompt appears (fig.
Page 7
Rev 0 – Aug, 2020 7. Set the EDID handshaking to position “A” for 4K video with 2ch audio. Choose setting “4” for 1080p video with 2ch audio. 8. Refer to the Connections, Buttons, and LEDs section for more information on the remaining control rotaries, slide switches, etc.
Page 8
Rev 0 – Aug, 2020 Additional configuration steps for control by KD-App and KDMS Pro 9. Set the desired Input/Output names by entering the Input/Output Settings section of the properties window, and selecting the Change Input/Output Name button (fig. 3a), selecting the desired input/output and entering the name (fig.
Option 1: Control via Remote Control 1. Output 1 display/projector control via CEC 2. Output 2 display/projector control via CEC 3. Input selection of KD-UFS42 connected sources 4. KD-CamUSB (sold separately) IR control Street Mt. Vernon, NY 10553 • www.keydigital.com...
Page 10
192.168.1.239, with port 23 • For the past 10 years, most Key Digital matrix switches have supported a standard audio + video switching command. KD-UFS42 is also controllable by this command, so if you have previously integrated Key Digital matrixes by third-party control systems you may have success using the same driver/module.
Rev 0 – Aug, 2020 Application Examples Complete Key Digital Presentation Solution CEC Controlled Presentation Space Street Mt. Vernon, NY 10553 • www.keydigital.com 521 East 3...
Page 12
Rev 0 – Aug, 2020 Simple Conference Room / Hybrid Classroom Lecture Hall with Wired and Wireless Presentation Street Mt. Vernon, NY 10553 • www.keydigital.com 521 East 3...
Rev 0 – Aug, 2020 Mounting Options KD-UFS42 includes hardware for multiple mounting options. • For mounting in a standard-width rack, use the included half-rack blank and short rack ear • For mounting under table or on wall, use the included L brackets •...
Exposure to rain or moisture Power Supply Use: You MUST use the Power Supply provided with your unit or you VOID the Key Digital® Warranty and risk damage to your unit and associated equipment. Street Mt. Vernon, NY 10553 • www.keydigital.com...