Advertisement
Figure 1. Strip Wire Insulation
IMPORTANT!
Not grounding this product, as described in the "Warnings
and Considerations" section, may result in an installation less immune to
damage caused by electrical disturbances, such as ESD or lightning, and
may void the warranty.
3
Identify and connect the keypad wires to the wallbox wires using the wire
nuts as shown in "Sample Wiring Configurations" in the Installation Guide for
the Control4 device that the Auxiliary Keypad is being connected to..
The yellow wire is not a traditional traveler. It cannot directly
IMPORTANT!
power a lighting load. It must be used only to connect to a compatible
Control4 load control device.
If you are using a Control4 push-on (screwless) faceplate in a multi-
TIP:
gang installation, attach the black faceplate sub-plate to all of the devices
that will be installed into the wallbox prior to attaching the devices to the
wallbox. This will help ensure that all the devices are properly aligned and
on the same plane after installation.
4
Fit the wires back into the wallbox. Bend the wires in a zigzag pattern so that
they easily fold into the wallbox (Figure 2).
Figure 2. Bend the Wires
5
Align the keypad to the wallbox (the model # label should be at the bottom)
and fasten it with screws. Tighten the screws until the back side of the yoke
plate is even with the wall surface, but no further. Overtightening can warp
the configurable keypad and cause mechanical malfunction.
6
Install the Control4 Faceplate following the instructions in the Faceplate
Installation Guide or attach a standard Decora-style faceplate.
7
Turn ON power at the circuit breaker or replace the fuse
from the fuse box.
Operation and Configuration
The Auxiliary Keypad acts as a slave device to the Control4 dimmer or switch to
which it is connected.
Click the top button to turn the load on. (When connected to a Fan Speed
Controller, each click of the top button increases the fan speed by one.)
Click the bottom button to turn the load off. (When connected to a Fan
Speed Controller, each click of the bottom button decreases the fan speed by
one.)
When connected to a dimmer, press and hold the top button to ramp the load
up. Release the button at the desired level.
When connected to a dimmer, press and hold the bottom button to fade the
load down. Release the button at the desired level.
Troubleshooting
If the Auxiliary Keypad does not control the load that is connected to the
associated dimmer, switch, or Fan Speed Controller:
Ensure that the circuit breaker is not turned OFF or tripped.
Check for proper wiring of both the Auxiliary Keypad and the associated
dimmer or switch (see "Sample Wiring Configurations"). You may also need to
contact a trained electrician.
For help on the installation or operation of this product, email or call the
Control4 Technical Support Center. Please provide your exact model number.
Contact support@control4.com or see the web site www.control4.com.
Care and Cleaning
Do NOT paint the keypad or its wall plate.
Do NOT use any chemical cleaners to clean the keypad.
Clean surface of the keypad with a soft damp cloth as needed.
Regulatory/Safety Information
To review Regulatory information for your particular Control4 products, see
the information located on the Control4 website at: http://www.control4.com/
regulatory/.
Patent Information
Applicable patents are available at http://www.control4.com/legal/patents.
Warranty
For complete warranty information, including details on consumer legal rights as
well as warranty exclusions, review the Warranty card or visit www.control4.com/
warranty.
About this Document
Part Number: 200-00311, Rev B 5/08/2013
Copyright ©2013 Control4. . All rights reserved. Control4, the Control4 logo, the Control4 iQ logo
and the Control4 certified logo are registered trademarks or trademarks of Control4 Corpora-
tion in the United States and/or other countries. All other names and brands may be claimed as
the property of their respective owners Pricing and specifications are subject to change without
notice
Advertisement
