Table of Contents
Advertisement
Note: Please get remote commander from the service parts when remote
commander is necessary for the repair.
• Use the bundled remote commander when remote commander is
bundled to the repairing set.
Part No. A-1717-785-A RM-ANU066
1. COLD RESET
Procedure:
1. Press the [
] button to turn on the system.
?/1
2. Press the [SYSTEM MENU] button on the remote command-
er.
3. Press the [
]/[
] buttons on the remote commander to select
M
m
the "SYSTEM", and press the [ENTER] button on the remote
commander.
4. Press the [
]/[
] buttons on the remote commander to select
M
m
the "RESET", and press the [ENTER] button on the remote
commander.
5. The message "RESET OK?" appears. Press the [ENTER] but-
ton on the remote commander, the cold reset is executed and
turn off the system.
2. PANEL TEST
Procedure:
1. Press the [
] button to turn on the system.
?/1
2. Touch the [VOLUME −] sensor and press the [
and hold for more than three seconds.
3. Then all segments of liquid crystal display are turned on and
all LEDs are lighted.
4. Touch the [
] sensor, the model name and destination are
u
alternately displayed.
/VOLUME −] sensor, the date and software
5. Touch the [
.
version are displayed.
6. Touch the [
/VOLUME +] sensor, enters the key test mode.
>
7. The message "KEY 0 --" appears. The "0" is changes "1" to
press the [
] button. The "--" is changes into "0" to "6" if the
?/1
corresponding touch sensor is touched.
8. To release from this mode, touch the [VOLUME −] sensor and
press the [
] button, and hold for more than three seconds.
?/1
3. S-AIR TEST MODE
Each item of S-AIR test is executed.
3-1. How to enter the S-AIR test mode
Procedure:
1. Press the [
] button to turn on the system.
?/1
/TUNING −] sensor and press the [
2. Touch the [
.
ton, and hold for more than three seconds.
3. The message "I2C" appears when correctly entering the S-AIR
test mode ("I2C" is one of the test mode items).
4. To release from this mode, touch the [
sor and press the [
] button, and hold for more than three
?/1
seconds.
3-2. I2C connection check
This mode is confi rm the I2C line between microcomputer and
EZW-RT10A.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [
]/[
] buttons on the remote commander to select
M
m
"I2C".
3. Press the [ENTER] button, the messages "OK" or "NG" is
displayed on the liquid crystal display. When the I2C line be-
tween microcomputer and EZW-RT10A is normal, "OK" is
displayed. When abnormality is found, "NG" is displayed.
4. Press the [ENTER] button on the remote commander, return to
S-AIR test mode each item.
SECTION 3
TEST MODE
3-3. Quality check
This mode is radio wave sensitivity state confi rmation of EZW-
RT10A.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [
3. Press the [ENTER] button on the remote commander, the mes-
4. Press the [ENTER] button, return to S-AIR test mode each
3-4. Power setting
This mode is setting of radio wave output of EZW-RT10A.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [
3. Press the [ENTER] button on the remote commander the mes-
4. Press the [
] button,
?/1
5. Press the [ENTER] button on the remote commander, return to
3-5. RF CH check
This mode is RF CH used is confi rmed.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [
3. Press the [ENTER] button on the remote commander, the mes-
4. Press the [ENTER] button on the remote commander, return to
3-6. ENC key change
This mode is setting of code key on/off change of EZW-RT10A.
Procedure:
1. Enter the S-AIR test mode.
] but-
?/1
2. Press the [
3. Press the [ENTER] button on the remote commander, the mes-
/TUNING −] sen-
.
4. Press the [
5. Press the [ENTER] button on the remote commander, return to
3-7. Version check
This mode is S-AIR version of the set connected with ATS-SW-
10Ti is confi rmed.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [
3. Press the [ENTER] button on the remote commander, S-AIR
4. Press the [
5. Press the [ENTER] button on the remote commander, return to
]/[
] buttons on the remote commander to select
M
m
"QUALITY".
sages "*** ###" is displayed on the liquid crystal display.
***: Minimum value (%)
###: Mean value (%)
item.
]/[
] buttons on the remote commander to select
M
m
"POWER".
sages "051 SET" is displayed on the liquid crystal display.
]/[
] buttons on the remote commander to select
M
m
the radio wave output. (OFF or 000 to 063)
S-AIR test mode each item.
]/[
] buttons on the remote commander to select
M
m
"CHK RFCH".
sages "*** CH#" is displayed on the liquid crystal display.
***: ON or OFF
#: CH number used
S-AIR test mode each item.
]/[
] buttons on the remote commander to select
M
m
"ENC KEY".
sages "ON" or "OFF" is displayed on the liquid crystal display.
]/[
] buttons on the remote commander to select
M
m
the "ON" or "OFF".
S-AIR test mode menu.
]/[
] buttons on the remote commander to select
M
m
"VER. CHECK".
version of the set connected with ATS-SW10Ti is displayed on
the liquid crystal display.
]/[
] buttons on the remote commander, change
M
m
the version and date displayed.
S-AIR test mode each item.
ATS-SW10Ti
9
Advertisement
Table of Contents
