Goodwe EM Series User Manual
Hybrid inverter
Hide thumbs
Also See for EM Series:
- User manual (18 pages) ,
- Quick start manual (9 pages) ,
- User manual (17 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Goodwe EM Series
Summary of Contents for Goodwe EM Series
- Page 1 PV Master APP SEMS Portal APP LinkedIn Company's official website EM SERIES USER MANUAL JIANGSU GOODWE POWER SUPPLY TECHNOLOGY CO.,LTD No. 90 Zijin Rd., New District, Suzhou, 215011, China HYBRID INVERTER www.goodwe.com 340-00313-01 service@goodwe.com Rev.1.1 2021-01-08...
-
Page 2: Table Of Contents
TABLE OF CONTENTS INTRODUCTION 1.1 Operation Modes Introduction ..................01 1.2 Safety & Warnings ......................02 1.3 Product Overview ......................04 INSTALLATION INSTRUCTIONS 2.1 Incorrect Installation ......................05 2.2 Packing List ........................05 2.3 Mounting ........................... 06 2.3.1 Selecting a Mounting Location ................ -
Page 3: Introduction
1.2 Safety & Warnings INTRODUCTION The EM series of inverters from Jiangsu GoodWe Power Supply Technology Co., Ltd. (also referred The GoodWe EM series of hybrid/bidirectional solar inverters are designed for use in solar systems to as Goodwe) strictly complies with relevant safety rules for product design and testing. Please... -
Page 4: Product Overview
1.3 Product Overview Safety Warning Installation and maintenance of the inverter must be performed by qualified electricians, in compliance with local authority and grid company standards, wiring rules and requirements (e.g., AS 4777 and AS/NZS 3000 in Australia). Before installing any wiring connection or electrically operating the inverter, all battery and AC power sources must be disconnected from inverter for at least 5 minutes to ensure the inverter is totally isolated to avoid electric shock. -
Page 5: Installation Instructions
The inverter must not be installed near flammable or explosive substances or strong Battery Hexagon Fixed Expansion EM SERIES USER MANUAL electromagnetic equipment. JIANGSU GOODWE POWER SUPPLY TECHNOLOGY CO.,LTD No. 90 Zijin Rd., New District, Suzhou, 215011, China HYBRID INVERTER www.goodwe.com 340-00313-01 Quick Installation service@goodwe.com... -
Page 6: Mounting
2.3.2 Mounting Step 3 Remember that this inverter is heavy! Please be careful when removing it from the The ground cable should be connected to the ground plate on the grid side. packaging. The inverter is suitable for mounting on concrete or other non-combustible surfaces only. Step 1 SYS TE BA CK -UP... -
Page 7: Electrical Wiring Connection
• The total short-circuit current of a PV string must not exceed inverter's max DC current. Ensure the breaker is off and the battery's nominal voltage meets EM series specifica- • The PV string's minimum isolation resistance to ground must exceed 18.33kΩ to prevent risk of tions before connecting the battery to the inverter. -
Page 8: On-Grid & Back-Up Connection
Battery Protection 1. Use a separate AC breaker for each 2. On the AC side, the individual breaker The battery will act as a protective charge/discharge current limiter under any of the conditions individual inverter. should be connected between the as below: inverter and the grid, and before the load. - Page 9 There is a solution to enable the inverter to work in on-grid mode in a SPLIT grid system. For Fastening Torsion details, please check the official application instructions on our website: GoodWe Hybrid 2. Make sure the cable sleeve is not trapped with the 0.55‒0.65Nm...
-
Page 10: Smart Meter & Ct Connection
Accepted Loads: Smart Meter & CT Connection Diagram The EM series inverter is able to supply a continuous 2300VA output or max 3500VA in less than 10 • For single phase grid seconds on the back-up side to support back-up loads. The inverter will derate for self-protection at high ambient temperatures. -
Page 11: Dred And Remote Shutdown Device Connection
2.6 Earth Fault Alarm Connection Step 2 The EM series inverter complies with IEC 62109-2 13.9. The fault indicator LED on the inverter cover will light up and the system will email fault information to customer. 1. Unplug the 6-pin terminal and disconnect The inverter should be installed at eye level for convenient maintenance. - Page 12 2.8 Wiring Scheme for EM Series Hybrid Inverters System Connection Diagrams Note: This diagram illustrates the wiring scheme for the EM series hybrid inverter, not the Note: In accordance with Australian safety regulations, the neutral cables of the on-grid side and electrical wiring standard.
-
Page 13: Wi-Fi Configuration
If you still need to configure details on the other pages, please Overview Param proceed to complete those as required. www.goodwe.com Help: When the received signal strength indicator (RSSI) for the selected Wi-Fi network is lower than 15%, the connection Configuration is now complete. You can log on to the may be unstable. -
Page 14: Others
OTHERS 4.1 Error Messages The error messages below will be displayed on the PV Master app or reported by e-mail if an error occurs. Error Message Explanation Reason Solutions 1. Use a multi-meter to check whether there is a voltage present on the AC side. Make sure grid power is available. Public grid power is not available (power Utility Loss Inverter cannot detect the connection of grid... -
Page 15: Troubleshooting
4.2 Troubleshooting Problems During Operation Checks Before Turning On AC Power Inverter does not start up with battery only • Battery Connection: Check the connection between the EM inverter and the battery: Polarities Solution: (+/-) must not be reversed (refer to figure 4.2-1). Ensure the battery voltage is greater than 48V, otherwise battery will be unable to start the EM •... - Page 16 Q: Which battery should I use with the EM series inverter? Questions & Answers (Q & A) A: Lithium batteries compatibility with EM series inverters, and with a nominal voltage of 48V can Wi-Fi Configuration be used. For compatible lithium batteries please refer to the battery list in the PV Master app.
-
Page 17: Disclaimer
About Smart Meter and Power Limit Function Q: How do I activate the output power limit function? EM series inverters must be transported, installed and operated under specified environmental and electrical conditions. The manufacturer has the right not to provide after-sales services or... -
Page 18: Technical Parameters
4.4 Technical Parameters Technical Data GW3048D-EM GW3648D-EM GW5048D-EM AC Output Data (Back-up) Technical Data GW3048D-EM GW3648D-EM GW5048D-EM Max. Output Apparent Power (VA) 2300 2300 2300 Battery Input Data Peak Output Apparent Power (VA)*8 3500, 10 sec 3500, 10 sec 3500, 10 sec Battery Type Li-lon Li-lon... -
Page 19: Other Tests
Please refer to 2.3.2 Mounting. Indoor Unconditioned -20~50℃ 5%~95% 3. Ensure the battery breaker is off and the battery's nominal voltage complies with EM series specifications before connecting the battery to the inverter, and ensure the inverter is fully Indoor conditioned 0~40℃... - Page 20 Pollution degree definition No pollution or only dry, non-conductive pollution occurs. Pollution Degree I The pollution has no influence. Normally only non-conductive pollution occurs. Occasionally, Pollution Degree II temporary conductivity caused by condensation must be expected. Conductive pollution occurs, or dry non-conductive pollution Pollution Degree III that becomes conductive due to condensation occurs, which is as expected.