Dakota Alert BBT-2500 User Manual
  1. Manuals
  2. Brands
  3. Dakota Alert Manuals
  4. Transmitter
  5. BBT-2500
  6. User manual

Dakota Alert BBT-2500 User Manual

Break beam transmitter
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
BBT-2500
Break Beam Transmitter
User Guide
PRODUCT DESCRIPTION:
The BBT-2500 is used with the DCR-2500 receiver. The BBT-2500 uses Active Infrared to detect anything that
passes through the sensor pair and breaks both beams at the same time. When the beams are broken, the
unit sends a signal to the receiver. This will sound one of four different tones (Classical, Westminster Chime,
Ding Dong, or Whistle). The BBT-2500 can be used to monitor access into any area, from your backyard to
lumber yard and everything in between.
NEW ZEALAND
AUSTRALIA
www.bealert.co.nz
www.bealert.com.au

Advertisement

Table of Contents
loading

Related Manuals for Dakota Alert BBT-2500

Summary of Contents for Dakota Alert BBT-2500

  • Page 1 This will sound one of four different tones (Classical, Westminster Chime, Ding Dong, or Whistle). The BBT-2500 can be used to monitor access into any area, from your backyard to lumber yard and everything in between.

  • Page 2: Hardware Installation

    DO NOT install this unit with any other infrared detector. It may cause false alarms. clean and inspect the unit regularly for proper use. If any problem is found, contact Dakota Alert, Inc. WARNINGS: This device complies with Part 15 of the FCC rules, Operation of this device is subject to the following conditions: 1.
  • Page 3 PAIRING: To make installation easier it is recommended to pair units ‘A’ and ‘B’ before mounting. On a flat surface push the power button (Figure 1-1) on ‘A’ then push the power button on ‘B’. Laying the units flat on counter or table, line up the infrared light holes (Figure 1-2). The units will then pair. You will see lights flashing during this process.

  • Page 4: Flat Surface Mounting

    Detailed below are the two most common mounting options. CIRCULAR POST MOUNTING: 1. Take the right angle bracket (Figure 3-1) and attach the cross bracket using (2) M4 nuts and (2) M4x12mm screws. Repeat for all brackets. 2. Using (2) M5 nuts and (2) M5x18mm screws attach right angle bracket (Figure 3-2) to units ‘A’...
  • Page 5 FOR ALL MOUNTING SITUATIONS: For all mounting situations In all mounting situations it is very important that the ‘A’ unit only interact with one ‘B’ unit or the pair may not alert properly. Use the diagrams below for reference. STRAIGHT LINE MOUNTING 300 metres 100 metres 100 metres...
  • Page 6 Locate the eight dip switches on the DCR-2500 and make sure they are set identically to dip switches 1-8 on the BBT-2500. Note: If more than one transmitter is used with the receiver, the first eight dip switches of all transmitters must match the eight dip switches of the receiver.

  • Page 7: Troubleshooting

    We will be happy to answer your questions and help you in any way we can. WARRANTY: Dakota Alert warrants this product to be free of defects in material and workmanship for a period of one year from the date of purchase. This warranty does not cover damage resulting from accident, abuse, act of God or improper operation.
  • Page 8 Freephone New Zealand: 0508 242 333 Freephone Australia: 1300 588 195 Phone (64) 6 751 2969 Fax (64) 6 751 2717 Fax (64) 6 751 2717 PO Box 7338, Toowoomba South 4350 PO Box 730, New Plymouth 4342 Queensland NEW ZEALAND AUSTRALIA...

Table of Contents