Page 1
Leica DI C800 User Manual / Installation Instructions 10 743 250 – Version 00...
Page 2
In developing our systems, we have placed great emphasis on simple, self-explanatory operation. Nevertheless, we suggest studying this manual so that you know and are able to utilize all the benefits of your Leica DI C800 in an optimum way. For valuable information about Leica Microsystems products and services and the address of your nearest Leica representative, please visit our website: www.leica-microsystems.com...
Page 3
Chapter overview Chapter overview Introduction Assembly Installation Operation Safety Notes Messages and Warnings Specifications Leica DI C800 / Ref. 10 743 250 / Version 00...
Directions for the user of the instrument Dangers during use Messages and Warnings Troubleshooting the mirrored data Troubleshooting the display Troubleshooting the optical system Specifications Electrical data Physical data Ambient conditions Standards Accessories Compatibility Leica DI C800 / Ref. 10 743 250 / Version 00...
Copy this information to the line below so that it is handy in case you have technically correct and efficient way. questions for our representatives or service locations. Action required; here, you are requested to take action. ➩ Type: Serial No.: Leica DI C800 / Ref. 10 743 250 / Version 00...
Overview of the typical load for the Accessories provided Leica DI C800 • XGA video cable (for connecting the Leica DI C800 to the workstation or to a PC) • Leica DI C800 User Manual / Installation Manual (10 743 250) Function of the Leica DI C800...
(at the beam splitter or at the second observer attachment) and remove the protective cover. ➩ Carefully insert the Leica DI C800 and fasten the clamping screw in place. Pay attention to the maximum load of the Leica surgical microscope during assembly of the Leica DI C800, see the microscope's User Manual.
3 XGA video cable (for a PC or workstation) (marked in blue) Look out for pinching of the CAN connecting cable (2) that may occur when laying the cable. Leica DI C800 / Ref. 10 743 250 / Version 00...
Setting up the Leica DI C800 Registering the Leica DI C800 at the control unit Set the minimum and maximum for brightness on the Leica DI C800 ➩ Select the "Setup" entry in the "Service" menu. ➩ Select the "Setup" entry in the "Service" menu.
Manually switch on/off the display containing overlaid data • Testimage Superimpose a test image in the eyepiece of the Leica DI C800 • Video signal is (in)correct Shows the status of the video signal Leica DI C800 / Ref. 10 743 250 / Version 00...
Assigning Leica DI C800 functions to footswitches or handles If a Leica DI C800 is connected and enabled, the "DI C800" function group is offered If a Leica DI C800 is connected and enabled, an additional "DI C800" tab appears in in the selection.
Operation During the surgery If a Leica DI C800 is connected and enabled, an additional "DI C800" quick access button appears in the static menu bar. Changing the current brightness of the overlay ➩ Click the "DI C800" quick access button.
➩ Protect the Leica DI C800 from improper operation. ➩ Remove dust on the optics of the Leica DI C800 using a bellows and a soft brush. • Only use the Leica DI C800 as described in this manual. Failure to observe these instructions may result in property damage.
Possible cause 1: The data source does not emit an image. ➩ Check whether the "DI C800" quick access button is present on the user interface. The plug connection for the XGA video cable is defective or the XGA video cable is connected incorrectly.
+24 V DC / max. 30 W Accessories Graphics interface RGB signals 0.7 V p–p / 75 Ohm Both 8.33x and 10x eyepieces can be used for the Leica DI C800. H sync and V sync VESA Standard 60/70/75 Hz at 1024(H) x 768(V) pixels Compatibility...