Installation In Vehicle; Securing The Child; Removing And Replacing The Cover - KIKKA BOO AMAIA Instructions For Use Manual

IMPORTANT: Check if the vehicle buckle has interference with child seat, try to another seat. Please contact our customer service
department if you are in any doubt. Always using the rear seats of your vehicle even if your highway codepermits the use on the front
seat.
VIII. INSTALLATION IN VEHICLE
SEAT INSTALLATION: 1.Place the child seat to the rearseat in the vehicle. Let the bottom of the seat against vehicle seat surface, and the
front of the seat touched vehicle seat backrest. 2.Then Extend the vehicle belt longer enough. Insert it from the slot at the front of the
seat, then through it into the slot at the another side. 3.Insert the buckle tongue into the vehicle buckle, and hear a "click". 4. Insert the
diagonal belt into the slot at the rear of car seat. 5,6.Pull the diagonal belt at the top of the vehicle buckle make the belt tight as show as
a arrows. As tight as you can.
INSTALLATION OF CHILD: Refer the to x your child carefully to nish the installation. Finally check the child seat is x stable on the
vehicle seat. If you nd any shake that you must tighten the belt again until the child seat is tight enough.
IMPORTANT: MISUSE THE CHILD CARSEAT WILL REDUCE THE PROTECT THAT THE SEAT PROVIDE. CHECK THE BELT AT THE RIGHT POSITION
AND IS TIGHT ENOUGH AT ALL OF THE POSITION, AND NO TWIST IS APPEARED.
IX. SECURING THE CHILD
When your child's weight is between 0-13kg.It need to x yourchild by the 3 point harness. According the follow steps:
1. Relax the harness before adjust the height, One hand press down the center adjuster at the same time the other hand hold the
shoulder belt and pull back.
2. Relax the buckle: push down the release button on the buckle, the buckle tongue will jump out. then put the harness to the both side
of seat.
3. Put your child on the child seat, let the buckle is on the front of your child's crotch. Make your child's arms through the should belt
(part no.03 page 01), the shoulder belt and the shoulder pad just on the top of your child's shoulder. Adjust the harness and headrest
height refer to. The top of the shoulder belt must be parallel or a little higher than the child'sshoulders. Too high or too low is not
suggested.
4. Reassemble buckle until you hear a "click". 5. Pull back the adjust belt make the harness tight. To be ensure there should not be more
than a ngers width between the harness and your child. It' s most importance of ensuring that any lap strap is worn low down, so that
the pelvis is rmly engaged, shall be stressed.
NOTICE: IF THE HARNESS IS TOO TIGHT, PLEASE RELAX IT THEN ADJUST IT AGAIN.
X. REMOVING AND REPLACING THE COVER
The fabric cover on this seat can be remove for washing, It just need release the plastic clip and pull out at the fringe of the seat . After
washing you can assemble it to the seat again.The seat cover is a part of the child seat. The child restraint must not be used without the
cover.The seat cover should not be replaced with any other than the one recommended by the manufacturer, because the cover
constitutes an integral part of the restraint performance. Suggestion:Do not wash the fabric frequent. It must assemble again as original
state after washing. To replace the cover, follow the steps of removing the cover in reverse order.
XI. WASHING AND MAINTENANCE
Check if there is any part has missed or broken, if this is the case. Do not use the seat again.
1. Fabric: Fabric can wash by the temperature less than 30 C , Then dry by nature condition.
2. Belt and plastic: Wash fabric with warm water and mild soap, do not use solvents or high-potency soap:
Do not remove ,move or change fabric and original fabric or any part of the harness.
3. Buckle: Always check that there is no food debris or other such matter in the harness buckle. This may affect the correct function of the
buckle please clean it by warm water. You can hear a "click" when the buckle function is normal.
ENGLISH