Table of Contents
Advertisement
IMPORTANT! KEEP FOR FUTURE REFERENCE!
EN
READ CAREFULLY!
I.PARTS
1.Headrest; 2. Small headrest; 3. Internal cushion; 4. Buckle; 5. Crotch pad; 6. Central adjuster; 7. Adjuster strap; 8. Adult seat belts guide gap; 9. Shoulder belts; 10. Backrest reclining
handle; 11. Rotation button; 12. ISOFIX button; 13. Headrest handle; 14. Top tether; 15. Child car seat; 16. ISOFIX connector.
II. PREPARATORY WORK AND FUNCTIONS
2.1 Prepare ISOFIX
1) If your car is not equipped with the ISOFIX guide socket, please insert the guide socket into the ISOFIX anchor.
TIP: ISOFIX anchors are located between the backrest and seat cushion.
2) Press the ISOFIX button push rearward to the longest.
2.2-2.3 Prepare Top Tether
1) Pull out the Top Tether and press the tether strap release button to extend the strap until it is long enough to connect it to the Top Tether anchorage point in the vehicle.
2) If the Top Tether is tightened favorably and correctly, the button will change to green.
2.4-2.6 Adjust the harness and headrest
Adjust the harness and headrest in the 5-point harness installation(From 40 up to105cm)
1) Press down on the central adjuster and pull the shoulder belts towards you, (DO NOT pull on the shoulder pads ) release the 5-point harness as far as it will go.
2) Pull upwards on the adjusting handle ,whilst pulling up or pushing down the headrest to the required position. Adjusting the height of the headrest will allow for the shoulder belts
to be the same level as the child's shoulders.
Adjust headrest(From 100 up to 150cm)
1) Make sure the 5-point harness is removed.
2) Make sure the seat cushion is removed.
3) Press on the adjusting handle in the direction of the arrow to release the headrest , and then adjust the headrest up or down to the desired position. Upon release of this handle, the
headrest will lock into place automatically.
4) The headrest is in the correct position when the diagonal belt section of the 3-point vehicle belt sits on the child's shoulders and when you can t 2 ngers between the seat belt
shoulder strap of the headrest and the shoulder of the child.
2.7 Use 360° rotation system
To rotate 180° in Rearward Facing (From 40 up to 105cm Rearward Facing)
1) Pull the rotation button outwards to release the child car seat , and then rotate the child car seat by 90°, at where the child car seat will lock into place automatically.
2) To rotate it back to the rearward facing position: pull the rotation button outwards to release the child car seat , and then rotate the child car seat by 180° back to the rearward facing
position, at where the child car seat will lock into place automatically.
3) Ensure the child car seat is at the rearward facing position and in fullest recline position.
4) Double check the bottom support.
To rotate 180° from Rearward Facing (From 40 up to 105cm) to Forward Facing(From 76 up to 150cm Forward Facing)
1) Pull the rotation button outwards to release the child car seat , and then rotate the child car seat by 180° at where the child car seat will lock into place automatically.
2) Adjust the recline position to the desired position if necessary.Ensure the child car seat is at the forward facing position, and the desired recline position.
Forward Facing( From 76 up to 150cm)
1) Pull the rotate button to push the child car seat, and then push the child car seat to one to ve forward facing gears. After releasing the rotate button, the child car seat will lock in
place automatically.
2) Ensure the child car seat is at the forward facing position,and the desired recline position.
III. INSTALLATION
WARNING!
Do not use forward facing before the child's age exceeds 15 months. If the vehicle is equipped with an active front seat airbag, DO NOT use the child seat in a rearward
facing position.
3.1-3.2 Rearward Facing Installation
With 5-point harness+ ISOFIX + Top Tether (40-105cm, from brith to approx. 15 months)
1) Prepare the ISOFIX.
2) Ensure that the 5-point harness is correctly installed and ensure that it is correctly adjusted.
3) Adjust the child car seat to the fullest recline position and make sure recline mechanism is securely locked.
4) Rotate the child car seat to the rear of the vehicle against the direction of travel. Ensure that the child car seat is in the rearward facing position and the rotation mechanism is securely
locked.
5) Double check to make sure that the child car seat is in the fullest reclined position.
6) Install the ISOFIX con rm that the indicator turns green and unfold the bottom support.
7) Push the child seat towards the backrest applying a rm, even pressure on both sides.
8) Children between 40 and 75cm need cushions to sit in seats when it exceeds 75cm, take o the seat cushion.
3.3-3.4 Securing your child with 5-point harness
1) Press the red button to release the 5-point harness buckle and press on the central adjuster to pull out the shoulder belts . DO NOT pull on the shoulder pads.
2) Place your child in the child car seat and ensure that your child's back is lying at against the backrest of the child car seat.
3) Guide the two buckle latches together and insert them into the 5-point harness buckle . An audible "click" will be heard once the buckle is locked.
4) Pull the adjuster strap towards you until the harness lies at and is close against your child's body.
3.5 For your child's safety, ensure that the following checks are carried out before every journey:
•
The ISOFIX connectors are securely engaged in the anchors and the indicators are both completely green.
•
The child restraint is sat up against the backrest of the vehicle seat.
ENGLISH
Advertisement
Table of Contents
