ESAB Cutmaster 120 Operating Manual page 92

ESAB CUTMASTER 120
Type Torch: SL100 With Shielded Tip
Type Plasma Gas: Air
Thickness Tip Output
Inches mm (Cat. No.) Volts(VDC)
0,250 6,4 9-8253 136
0,375 9,5 9-8253 144
0,500 12,7 9-8253 149
0,625 15,9 9-8253 153
0,750 19,1 9-8253 157
1,000 25,4 9-8253 162
1,250 31,8 9-8253 165
Type Torch: SL100 With Shielded Tip
Type Plasma Gas: Air
Thickness Tip Output
Inches mm (Cat. No.) Volts(VDC)
0,250 6,4 9-8253 144
0,375 9,5 9-8253 148
0,500 12,7 9-8253 152
0,625 15,9 9-8253 162
0,750 19,1 9-8253 163
1,000 25,4 9-8253 168
NOTE!
* Gas pressure shown is for torches with leads up to 25' / 7.6 m long. For 50' / 15.2 m
leads, refer to Section "Set Operating Pressure" on page <?>.
** Total flow rate includes plasma and secondary gas flow.
4T-18
Amperage Speed (Per Minute)
(Amps) Inches Meters Inches
120 180 4,57
120 100 2,54
120 60 1,52
120 40 1,02
120 30 0,76
120 20 0,51
120 10 0,25
Amperage Speed (Per Minute)
(Amps) Inches Meters
120 190 4,83
120 120 3,05
120 75 1,91
120 45 1,14
120 35 0,89
120 20 0,51
OPERATION
Type Material: Stainless Steel
Type Secondary Gas: Single Gas Torch
Standoff Plasma Gas Press
mm psi* bar Plasma Total** Delay (Sec) Inches
0,13 3,2 75 5,2
0,13 3,2 75 5,2
0,13 3,2 75 5,2
0,15 3,8 75 5,2
0,15 3,8 75 5,2
0,15 3,8 75 5,2
0,15 3,8 75 5,2
Type Material: Aluminum
Type Secondary Gas: Single Gas Torch
Standoff Plasma Gas Press
Inches mm psi* bar
0,13 3,2 75 5,2
0,13 3,2 75 5,2
0,15 3,8 75 5,2
0,15 3,8 75 5,2
0,15 3,8 75 5,2
0,15 3,8 75 5,2
Flow (CFH) Pierce Pierce Height
180 360 0,20 0,20
180 360 0,40 0,20
180 360 0,80 0,20
180 360 1,20 0,20
180 360 NR NR
180 360 NR NR
180 360 NR NR
Flow (CFH) Pierce Pierce Height
Plasma Total** Delay (Sec) Inches
180 360 0,20 0,20
180 360 0,50 0,20
180 360 0,70 0,20
180 360 1,00 0,20
180 360 NR NR
180 360 NR NR
300X5398
mm
5,1
5,1
5,1
5,1
NR
NR
NR
mm
5,1
5,1
5,1
5,1
NR
NR