Page 2
The totally new developed HET differentials are included to provide more traction which was not possible with old system. The new S35-GT2 comes with a lower shock layout for the front and rear. Newly developed shocks are now catered to this new optimized layout.
Page 3
Contact your local hobby shop or SWORKz distributor for all claims and questions. Claims must be well documented. All Claims are subject to expert...
Page 4
Index Required equipment for operation Operation guide Assembly steps 7-36 Set-up sheet Blank set-up sheet 38-39 S35-GT2 Key No. List 40-41 S35-GT2 Spare Part List 41-42 S35-GT2 Option Part List Explosion view with spare parts number 44-47 End cover This radio controlled racing car is not a toy!
Page 5
R e q u i re d Equ ip me nt fo r O p erat io n Radio Gear Nitro fuel Receiver batteries Stick Type We recommend that you use fuel containing 20~25% nitro. Throttle servo On/Off Switch Receiver Wheel &...
Page 6
The SWORKz S35-GT2 is a high performance radio control model which needs to be operated with caution and common sense. The S35-GT2 Pro Kit is not intended for children under the age of 14 without adult supervision. SWORKz shall not be held liable for any loss or damages, whether direct, indirect, act of nature, arising from the abuse or misuse of this product or any other product required while operating this model.
Page 7
610023 328001 101004 101004 101004 Washer 3.5X10X0.2mm 328001 101004 338025 328001 101004 Fill the differentials with oil up to 80% above the satellite gears. Put the SWORKz Diff. Oil 500000cps for the front Diff. and 50000cps for the rear Diff.
Page 9
Pro Tip: Before installing the M5x4 set screw (104010), remember to clean the set screw and center driver joint (330661A) first. Then apply TLC on the set screw. 338023 106019R 338011 106019R 104010 M5x4mm Set Screw (Flat Bottom) 228001(#8 #9 #10) 330661A 2503261A 108001...
Page 10
Pro Tip: Before installing the M5x4 set screw (104010), remember to clean the set screw 338023 and center driver joint (330661A) first. Then apply TLC on the set screw. 106019R 108001 338011 330661A M3x12mm FH/ST HEX Screw 106019R 228001(#2 #3 #4) 104010 338082 2503261A...
Page 11
108008 M3x35mm FH/ST HEX Screw 101020A 3mm Countersunk Washers (GM) 228001(#5 #6 #7) 338056 338058 108008 228001(#5 #6 #7) 101020A 338056 S35-4 Series Lower Arm Hinge Pin (68.5mm) 2503261A Pop in the Stabilizer Guide. 104004 M3x3mm Set Screw 104004 104004 115008A (2.3mm) 115035A (2.2mm)
104005 M3x4mm Set Screw 106013 M2.5x8mmH ex Socket OH/TPScrew 106013 104005 Note: The aluminum front upper arm holder (338057) can offer either 0° or + -1° kick-up for your front upper arm suspension. You may use the inserts 228001(#13) to get 0° kick-up or 228001(#12) to get +-1°...
PRO TIP: The S35-GT2/2e Front Upper Arm Adjust Inserts can give different steering adjustments (Ackerman). Put all inserts behind the front upper arms, you will get faster steering response. Otherwise put all inserts in front of the upper arms, you will get more stable steering response.
Page 14
PRO TIP: The S35-GT2/2e Aluminum Rear Lower Fully Adjustable Toe-In Block (330770) can use 3 types of square inserts to get 1.0/2.0/3.0 3 different toe in angles. Also plus 3 different rear lower arm kick up degrees. 338056 228001(#2 #3 #4)
108003 108003 M3x10mm FH/ST HEX Screw 108003 116004R Ball Bearing 6x10x3mm (Red Rubber Case) 101019 SHIM 6.0x10.0x0.2mm 101019 116004R 338048 106002 106002 M3x10mm Hex Socket OH/TP Screw Right 338051 330252 2503260-04 330118A Left 330118A 2503264A 330252 Screw and adjust 330118A Knuckle 2503260-04 Pivot Ball Nut so as the pivot ball can be moved smoothly.
Page 17
104010 Left M5x4mm Set Screw (Flat Bottom) 330124 Pin M3.0x16.8mm 116006R 116006R Ball Bearing 8x16x5mm (Red Rubber Case) 210046 116006R 330124 Right 101018 SHIM 13x16x0.2mm 104010 Note: 101018SHIM 13x16x0.2mm Please use 13x16x0.2mm shims to adjust the 101018 gap between the wheel hub and wheel knuckles. Standard suggestion is 1pc shim on the outside between 8x16x5mm ball bearing and knuckle.
Page 25
106002 M3x10mm Hex Socket OH/TP Screw 106002 106008 106008 106003 106003 106008 M3x12mm Hex Soket OH/TP Screw 106003 Servos are not M3x16mm Hex Soket OH/TP Screw included in the kit. 2503262 2503262 2503262...
Page 26
106002 Receiver and switch are The switch is not not included in the kit. included in the kit. 103001 M3 Nut Lock 106002 M3x10mm Hex Socket OH/TP Screw Laps transponder is not included in the kit. 103001 108006 108006 108006 M3x8mm FH/ST HEX Screw 2503262...
Page 27
Li-ion Size:18500 104004 106001 106001 M3x3mm Set Screw Battery is not included in the kit. 2503262 106001 200193 Li-ion Size:18650 104004 106001 M3x8mm Hex Socket OH/TP Screw 108006 M3x8mm FH/ST HEX Screw 108006 108006 108006...
When the volume 106002 of fuel tank system 106020 is over 150cc, 210048X using the part 108006 2502040-02 210048 can be M3x8mm FH/ST HEX Screw 2502040-02 reduced 2cc for your fuel tank. 210048X 106020 M2.5x5mm Hex Socket OH/TP Screw 106020 106002 M3x10mm Hex Socket OH/TP Screw 108006...
Page 43
S35-3 Series Lightened Aluminum Front Chassis Shorty Brace SW-338035 S35-3 Series Lightened Aluminum Rear Chassis Brace SW-338036 SWORKz 1/8 Nitro Series Pipe Spring Lock (1 set) SW-338075 S35-4 Series T7 Aluminum Rear Wheel Hub (R=L)(2PC) SW-338070A S35 Series Rear Upper Arm Aluminum Ball Stud (2PC)
Page 44
Par ts No. Li st E xp lo d e d View Shock Absorbers 108029 2501121C 338067 400022AS 330798 350002A(F) 103004 350003A(R) 400019 330560B 101011 F/R 338099 210058 400020 330557 SWC-115148A 228006 330134 Differential 116006R 330802AH 104010 104016 330833 330811 330832 Center 104016...
Page 46
Par ts No. Li st E xp lo d e d View Center Transmission 108006 105005 610004 2501126 101013 101013 610004 2501126 106001 2501126 101038 2503262 330008A 115027A 106001 330100A 200193 106002 104004 338007 108006 338005 338003 2503262 115027A 105001 106003 330006 105007A 106008...
Need help?
Do you have a question about the S35-GT2 and is the answer not in the manual?
Questions and answers